Related Manuals for Philips AJ3650/12
Summary of Contents for Philips AJ3650/12
- Page 1 Clock Radio AJ 3650 User Manual Manuel d'utilisation Manual de usuario Benutzerhandbuch Gebruikershandleiding Manuale dell'utente...
- Page 2 R E P E AT A L A R M / B R I G H T N E S S C O N T R O L FOCUS DISPLAY DATE/SET TIME AUTO SCAN...
- Page 3 & Model No. : AJ3650/12 3V CR203 2 (Backup Battery) Ext AC-DC Adaptor 7.5V 1A Clock memory back up CR2032 battery Designed and Developed by Philips, Holland PRESET TUNING VOLUME DC IN 7.5V...
- Page 5 Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. SUPPLIED ACCESSORIES – 1 switching power adapter (Model: DSA-9W-69F EU 075100, Input: 100-240V~50/60 Hz, 0.5 A, Output: 7.5 V, 1.0 A) –...
- Page 6 6 REPEAT ALARM/BRIGHTNESS CONTROL – turns off the alarm temporarily and repeats alarm after 9 minutes – press to turn on or off the blue background light 7 AUTO SCAN – in tuner mode, press and hold it to scan radio stations automatically and stores them as preset stations –...
-
Page 7: Lcd Display
$ VOLUME – adjusts the sound level % DC IN – socket for AC/DC 7.5 V adapter ^ Pigtail – temperature sensor and antenna to enhance FM reception & RESET – press if the set does not react to operation of any button * Battery compartment –... -
Page 8: Setting The Clock
2 Always disconnect the mains adapter if you are not using the set. Helpful hints: To avoid damage to the set, use only the adapter supplied! SETTING THE CLOCK The clock uses 24-hour time format. Important! Pull out the plastic protective sheet to activate the clock backup battery (CR2032). -
Page 9: Storing Preset Stations
13. Press DATE/SET TIME to confirm. ™ Hr and offset number start flashing. 14. Press TUNING +/- repeatedly to set the desired hour offset value. 15. Press DATE/SET TIME to confirm. RADIO TUNING TO RADIO STATONS Automatic tuning • Press and hold TUNING +/- to automatically tune to the next or previous station of sufficient reception. -
Page 10: Using The Alarm
™ Display shows the radio frequency of the last selected station briefly before returning to the clock time. Your preset station is also shown if you are listening to a preset station. 2. Adjust volume by turning VOLUME. 3. Press RADIO to switch off. Helpful hints: –... - Page 11 SWITCHING OFF THE ALARM REPEAT ALARM This repeats your alarm call at 9 minute intervals. • During the alarm call, press REPEAT ALARM /BRIGHTNESS CONTROL. ™ Alarm sound indicator flashes during a repeat alarm. • Repeat if desired. DEACTIVATING THE ALARM COMPLETELY •...
- Page 12 along the horizontal axis. 5. Push the projection cone to pop it out (See 4). 6. To change the projection slightly to a different angle, turn the IMAGE ROTATE wheel (maximum 90 degree left or right). 7. Press PROJECTION/IMAGE FLIP to switch between: bright, dim, very dim and off. Helpful hints: –...
-
Page 13: Low Battery Indication
• Press and hold AUTO SCAN for about 3 seconds to start searchings for the remote sensor signal. Note: – Each time you change a channel, press RESET both on the sensor and main unit, and then press and hold AUTO SCAN on the main unit to search the sensor.INDOOR TEMPERATURE The set can also automatically measure and display current temperature in Centigrade. -
Page 14: Troubleshooting
TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee. - Page 15 Blurry projection – Angle between the projection surface too large • Adjust the angle. – Focus is not proper • Turn FOCUS wheel. The main unit cannot read or update outdoor temperature from the sensor – No signal or weak signal. •...
- Page 16 Disposal of your old product Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products.
-
Page 17: Class 1 Laser Product
Clock radio Meet Philips at the Internet http://www.philips.com English Français Español Deutsch Nederlands Italiano CLASS 1 LASER PRODUCT Printed in China AJ3650_12_UM_V2.0...