Advertisement
WARNING! Ensure you read, understand and apply Section 1 safety instructions before use.
5.2
Thicknessing
5.2.1
Set the desired height by turning the handle (Fig.B) using the graduated scale as a reference.
5.2.2
One complete turn of the handle is equal to 3mm as indicated on the scale next to the feed port.
It is better to use a cutting depth of between 0.5 and 1.5 mm (1/64"~1/16") for best results. Trying to
remove excessive amounts on a single pass will result in motor overload and dull the blades.
Note!
When thicknessing it is recommended to keep the feed table clean and free of sap. Apply a small
amount of penetration spray and wipe over with a cloth.
WARNING! Do not remove chips or dust from the table while the machine is running, always disconnect from
!
the mains supply before attempting any kind of maintenance. Do not attempt to thickness short pieces of wood.
6. MAINTENANCE
! WARNING! Prior to doing any maintenance work, always disconnect from the mains. Any protective guards which have been removed must be
mounted again after the maintenance work.
6.1
MACHINE CARE
The SM1311 is designed with a low maintenance
requirement. The bearings are greased for life.
6.1.1
Grease threaded spindles for the height
adjustment of the thicknessing table.
6.1.2
The table surface should always be kept free of
resin.
6.1.3
In order to prevent the motor from overheating,
regularly check that no dust has accumulated on
the ventilation apertures of the motor.
After a prolonged period of operation, users are
recommended to have the machine checked by an
authorised service agent.
6.2
TOOL CARE
The cutter head, clamping devices, blade supports and
blades used on the machine must be kept free from resin
build up as a clean tool improves the cutting quality. This can
be done by soaking the blade supports and blades for 24
hours in paraffin, white spirit or commercially available resin
remover.
6.3
REPLACING BLADES
! WARNING! Disconnect from power before servicing!
6.3.1
Unplug the planer from power source.
6.3.2
Loosen and remove four blade lock screws
securing blade and blade clamp.
6.3.3
Lift blade and blade clamp from cutterhead.
6.3.4
Clean any sawdust and resin build up from cutterhead and blade clamp.
6.3.5
Place blade clamp against the replacement blade and replace in cutterhead.
6.3.6
Secure blade and blade clamp using four blade lock screws. Do not over-tighten.
NOTE! Check blade height and alignment.
6.3.7
To check blade alignment, set the table to the (0) position. Use a straight edge i.e metal ruler or set square and position it across the
two tables. The blade should almost make contact with the ruler, check at either end of the blade and in the middle to ensure the blade
is level. Loosen the blade lock screws and adjust height accordingly using the blade adjustment grub screws.
6.3.8
Repeat the procedure to replace the other blade.
6.3.9
Make sure all the blade lock screws are tight.
7. DECLARATION
Declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in conformity with the following
standards and directives.
PLANER/THICKNESSER 200x120mm
Model SM1311
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
The construction file for this product is held by the Manufacturer and may
be inspected, by a national authority, upon request to Jack Sealey Ltd.
Signed by Steve Buckle
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
Fig.B
Height adjustment for
thicknesser table
1st May 2006
www.sealey.co.uk
Web
sales@sealey.co.uk
email
SM1311 - 1 - 150506
Advertisement
