1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Server
  5. ThinkServer RD350G
  6. User manual and hardware maintenance manual

Lenovo ThinkServer RD350G User Manual And Hardware Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ThinkServer RD350G
User Guide and Hardware Maintenance
Manual
Machine Types: 70D6, 70D7, 70D8, 70D9, 70QK, 70QL, 70QM,
and 70QN

Advertisement

Table of Contents
loading

Related Manuals for Lenovo ThinkServer RD350G

Summary of Contents for Lenovo ThinkServer RD350G

  • Page 1 ThinkServer RD350G User Guide and Hardware Maintenance Manual Machine Types: 70D6, 70D7, 70D8, 70D9, 70QK, 70QL, 70QM, and 70QN...
  • Page 2 • Appendix A “Notices” on page 155 Sixth Edition (May 2016) © Copyright Lenovo 2014, 2016. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.

  • Page 3: Table Of Contents

    Lenovo Partner Pack for Microsoft System Configuring RAID ..............50 Center Operations Management ......12 About RAID ..............50 Lenovo Partner Pack for VMware vCenter . . 13 Configuring RAID using the Lenovo Lenovo ThinkServer Deployment Manager . . 13 ThinkServer Deployment Manager program .
  • Page 4 Japan VCCI Class A compliance statement . . . Basic troubleshooting tables ........... 146 ENERGY STAR model information ..Lenovo ThinkServer Deployment Manager program problems ............ 146 Optical drive problems ..........146 Index ............. 167 Storage drive problems ..........147 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 5: Safety Information

    제품을 사용하기 전에 제품과 함께 제공되는 문서 디스크의 다국어 안전 지침을 주의 깊게 읽어보십시오. Voordat u het product gebruikt, moet u ervoor zorgen dat u de meertalige veiligheidsinstructies op de documentatieschijf van het product hebt gelezen en begrijpt. © Copyright Lenovo 2014, 2016...
  • Page 6 Ensure that you read and understand all caution and danger statements in this document before you perform the procedures. Read and understand any additional safety information that is included with the server or optional device before you install, remove, or replace the device. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 7 Connect cables when oduct cables devices. cables ors. cables ors. cables devices. devices Statement 2 DANGER Danger eplaced. the same ecommended the manufactur immerse 100° C Repair © Copyright Lenovo 2014, 2016...
  • Page 8 The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 9 Statement 9 CAUTION: Disconnect the hot-swap fan cables before removing the fan from the device to protect against personal injury. Statement 10 CAUTION: The following label indicates a sharp-edge hazard. © Copyright Lenovo 2014, 2016...
  • Page 10 In addition, the device might have multiple connections to dc power. To remove all electrical current from the device, ensure that all connections to dc power are disconnected at the dc power input terminals. viii ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 11 This product contains a Class 1M laser. Do not view directly with optical instruments. Statement 18 CAUTION: Do not place any object on top of rack-mounted products. Statement 19 CAUTION: Hazardous moving parts. Keep fingers and other body parts away. © Copyright Lenovo 2014, 2016...

  • Page 12: Products That Are Not Assessed

    Statement 20 CAUTION: A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations. Products that are not assessed Typical products that are not assessed include but not limited to the following: •...

  • Page 13: Grounding Requirements

    9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with. Grounding requirements Electrical grounding of the server is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. © Copyright Lenovo 2014, 2016...
  • Page 14 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 15: Chapter 1. General Information

    The Lenovo Limited Warranty (LLW) contains the warranty terms that apply to the product you purchased from Lenovo. Read the LLW on the documentation disc that comes with your server. A printable generic version of the latest LLW also is available in more than 30 languages at http://www.lenovo.com/warranty/llw_01.

  • Page 16: Server Documentation

    When you register your server, information is entered into a database, which enables Lenovo to contact you in case of a recall or other severe problem. After you register your server with Lenovo, you will receive quicker service when you call Lenovo for help. In addition, some locations offer extended privileges and services to registered users.
  • Page 17 Note: Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. Some information in the documents on the documentation disc might change without notice after the first release of the disc.
  • Page 18 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 19: Chapter 2. Server Setup Road Map

    9. Configure Ethernet settings in the operating system by referring to the operating system help. This step is not required if the operating system was installed using the Lenovo ThinkServer Deployment Manager program. 10. Check for firmware and driver updates. See “Updating the firmware” on page 53.
  • Page 20 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 21: Chapter 3. Product Overview

    Product Specifications Reference document for ThinkServer products at: http://www.lenovo.com/psref/ Microprocessor ® ® One or two Intel Xeon microprocessors (internal cache size varies by model) Memory Your server has 16 memory slots. For more information, see “Memory module installation rules” on page 62. © Copyright Lenovo 2014, 2016...
  • Page 22 – You can install SATA hard disk drives, SAS hard disk drives, and solid-state drives into the same server. • Optical drive – One slim SATA optical drive in some models To locate the internal drives or drive bays, see “Server components” on page 23. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 23 Expansion slots • One PCI Express (PCIe) slot on the system board • One PCIe slot on each riser card • Two riser card assembly slots on the system board For detailed information, see “Rear view of the server” on page 21. Input/Output (I/O) features •...

  • Page 24: Features

    Your server supports onboard SATA software RAID. If a required RAID card is installed, your server also supports advanced SATA/SAS hardware RAID configurations. For detailed information, see “Configuring RAID” on page 50. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 25: Specifications

    The advanced system management features are only available when the TSM detects the presence of a TSM Premium module. The TSM Premium module is a remote management module. You can purchase a TSM Premium module from Lenovo and install it on the system board to activate the advanced system management features.

  • Page 26: Software

    BIOS and TSM update utilities The BIOS and TSM (also known as BMC) firmware keeps updating after the shipment of the server. Lenovo maintains pages on the Support Web site and provides the BIOS and TSM update utilities with instructions for download to help you update the BIOS and TSM firmware if needed.

  • Page 27: Lenovo Partner Pack For Vmware Vcenter

    • Ability to install the operating system and device drivers in an unattended mode to save time • Ability to create a reusable response file that can be used with similarly configured Lenovo servers to make future installations even faster •...

  • Page 28: Lenovo Thinkserver Diagnostics

    Diagnostics section at the bottom of the Web page. Then, click the desired link for more information. Lenovo ThinkServer Operating System-based Platform Update Tool The Lenovo ThinkServer Operating System-based Platform Update Tool is used to update the firmware in the operating system for your server.

  • Page 29: Lenovo Thinkserver System Manager Premium

    Lenovo XClarity Administrator Information Lenovo XClarity Energy Manager The Lenovo XClarity Energy Manager (hereinafter referred to as Energy Manager) is a tool for data center power management. It monitors the power and temperature at the device level and the group level. By monitoring and analyzing power and temperature information, Energy Manager helps you increase power efficiency and improve business continuity.
  • Page 30 Note: Depending on the model, your server might look slightly different from the illustrations in this topic. Figure 1. Label on server models with 3.5-inch-drive bays Figure 2. Label on server models with 2.5-inch-drive bays ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 31: Front View Of The Server

    Front view of the server The front view of the server varies by model. The illustrations in this topic show the server front views based on the supported internal drives: • “Front view of server models with 3.5-inch drives” on page 17 •...
  • Page 32 The number of the installed drives in your server varies by model. The vacant drive bays are occupied by dummy trays. When you install drives, follow the order of the drive bay numbers. Slim optical drive Some server models come with a slim SATA optical drive. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 33: Front Panel

    Front panel The following illustration shows the controls, connectors, and LEDs on the front panel of the server. The front panel varies by model. Figure 5. Front panel Network status LED System health LED Power button with power status LED System ID button with ID LED USB 2.0 connectors (2) VGA connector...
  • Page 34 The voltage of the server reached the non-critical voltage Replace the system board. threshold. Note: This action must be performed only by Lenovo service personnel. See Chapter 8 “Getting information, help, and service” on page 151. A fan is running at low speed.

  • Page 35: Rear View Of The Server

    System ID button with ID LED When you press the system ID button, the ID LEDs on both the front and rear of the server are lit to help you locate the server among other servers. You also can turn on the ID LEDs using a remote management program for server presence detection.
  • Page 36 The hot-swap redundant power supplies help you avoid significant interruption to the operation of the system when a power supply fails. You can purchase a power supply option from Lenovo and install the power supply to provide power redundancy without turning off the server.

  • Page 37: Server Components

    Ethernet status LED Color Status Description Left Amber The connection speed is 1000 Mbps. Green The connection speed is 100 Mbps. None The connection speed is 10 Mbps. Right The server is connected to a LAN. Green None The server is disconnected from a LAN. Blinking The LAN is connected and active.
  • Page 38 Rack handle (left) Slim optical drive (available on some models) System fans Heat sink(s) with microprocessor(s) underneath Riser card assembly 1 Secure digital (SD) module (available on some models) Riser card assembly 2 ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 39 FRU information, such as FRU part numbers and supported server models, go to: http://www.lenovo.com/serviceparts-lookup Notes: • Before servicing a Lenovo product, ensure that you read and understand “Safety information” on page iii. • Use only parts provided by Lenovo. * Available on some models...

  • Page 40: Raid Card

    This topic provides information to help you locate the connectors on a RAID card. If your server has a RAID card installed, the RAID card is seated on the riser card assembly 2. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 41 Used to connect a mini-SAS signal cable to the mini-SAS ports 4-7 on the backplane for 2.5-inch drives. TR 500 key connector Used to connect a Lenovo ThinkServer RAID 500 RAID 5 Upgrade Key for Advanced RAID. See “Installing or removing the Lenovo ThinkServer RAID 500 or 520i upgrade key” on page 75.
  • Page 42 Used to connect the mini-SAS signal cable connector on the backplane to support HDD 0-3. Connector 1 Used to connect the mini-SAS signal cable connector on the backplane to support HDD 4-7. J3 connector Used to connect to a ThinkServer RAID 520i upgrade key. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 43 ThinkServer RAID 710 Adapter The following illustration shows the connectors on the ThinkServer RAID 710 Adapter. Figure 11. ThinkServer RAID 710 Adapter Connector 1 Used to connect a mini-SAS signal cable to the mini-SAS ports 0-3 on the backplane. Connector 2 Used to connect a mini-SAS signal cable to the mini-SAS ports 4-7 on the backplane for 2.5-inch drives.

  • Page 44: Hot-Swap-Drive Backplane

    Hot-swap, SATA or SAS 3.5-inch Hard disk drive or 2.5-inch solid-state drive Hot-swap, SATA or SAS 2.5-inch Hard disk drive or solid-state drive To locate the backplanes, see “Server components” on page 23. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 45 Backplane for 3.5-inch drives The following illustrations show the slots and connectors on the backplane for 3.5-inch drives. Figure 13. Front view of the backplane for 3.5-inch drives Figure 14. Rear view of the backplane for 3.5-inch drives Slot 0-slot 3 Used to connect 3.5-inch drives.
  • Page 46 4 to hard disk drive 7. Mini-SAS ports 0-3 Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the hard disk drive 0 to hard disk drive 3. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 47: System Board Components

    System board components The following illustration shows the component locations on the system board. Figure 17. System board components SATA connector (optical drive) Coin-cell battery SATA connector 1 (ports 4–7) Storage-drive power connector Front panel connector 1 SATA connector 0 (ports 0–3) Front panel connector 2 SD module connector Riser card assembly 1 slot...
  • Page 48 Used to install a supported PCIe card. For information about supported PCIe cards, see “Rear view of the server” on page 21. Riser card assembly 2 slot Used to install the riser card assembly 2. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 49 RAID upgrade key connector Used to connect a ThinkServer RAID 110i upgrade key. Power supply connector 2 Used to connect the power supply 2. Power supply connector 1 Used to connect the power supply 1. Intrusion switch connector Used to connect to an intrusion switch. Backplane power connector Used to connect to the 10-pin power connector on the backplane.

  • Page 50: System Board Jumpers

    2. Prepare your server. See “Removing or extending the server from the rack cabinet” on page 57. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 51 3. Remove the server cover. See “Removing the server cover” on page 57. 4. Locate the BIOS default settings jumper on the system board. Then, remove any parts and disconnect any cables that might impede your access to the jumper. Note: Do not remove the memory modules or microprocessors.

  • Page 52: Hot-Swap-Drive Status Leds

    User Guide. You can obtain the most up-to-date documentation for your server from the Lenovo Web site at: http://www.lenovo.com/UserManuals Blinking, green Blinking slowly (about The drive is being rebuilt. one flash per second), amber ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 53: Power Supply Status Leds

    Power supply status LEDs Each hot-swap power supply has three status LEDs. Figure 20. Power supply status LEDs Description Action Status Input status LED Off The power supply is No action is needed. disconnected from the ac power source. On, green The power supply is connected No action is needed.
  • Page 54 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 55: Chapter 4. Turning On And Turning Off The Server

    • When you turn off the server and leave it connected to an ac power source, the server also can respond to a remote request to turn on the server. To remove all power from the server, you must disconnect the server from the ac power source. © Copyright Lenovo 2014, 2016...
  • Page 56 • For information about your specific operating system, refer to the related documentation or help system for the operating system. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 57: Chapter 5. Configuring The Server

    BIOS default settings jumper to restore the BIOS settings to the factory default settings. See “System board jumpers” on page 36. • If you have changed any hardware in the server, you might need to upgrade the BIOS and the TSM firmware. © Copyright Lenovo 2014, 2016...

  • Page 58: System Information Menu

    • “Save & Exit menu” on page 45 Lenovo provides the BIOS update utility on the Lenovo Support Web site. You can download the BIOS update utility to update the BIOS. See “Updating or recovering the BIOS” on page 49.

  • Page 59: Boot Manager Menu

    System Security menu You can set passwords and configure the TPM function on the System Security menu in the Setup Utility program. For each menu item, press Enter to show selectable options and select a desired option by using the up and down arrow keys or type desired values from the keyboard. Some items are displayed on the menu only if the server supports the corresponding features.

  • Page 60: Setting The System Date And Time

    • The Setup Utility program passwords are not case sensitive. • The server supports Setup Utility program passwords that consist of three to 32 characters. To set a strong password, use the following guidelines: ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 61: Selecting A Startup Device

    • Have at least eight characters in length • Contain at least one alphabetic character and one numeric character • Not be your name or your user name • Not be a common word or a common name • Be significantly different from your previous passwords Besides the alphabetic characters (a-z) and numeric characters (0-9), the server also supports characters typed using special keys on the keyboard for a password.

  • Page 62: Configuring The Tpm Function

    The TPM works as a hardware security solution to help you to encrypt data and protect the server. The TPM function is only available when there is a TPM installed in your server. See “Installing the TPM” on page 71. You can purchase a TPM from the Lenovo Web site at: http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server After installing a TPM, check if the TPM function is enabled in the Setup Utility program.

  • Page 63: Updating Or Recovering The Bios

    This topic provides instructions on how to update the BIOS and how to recover from a POST and BIOS update failure. Lenovo might make changes and enhancements to the BIOS and TSM firmware. When updates are released, they are available for download on the Lenovo Web site at http://www.lenovo.com/drivers. You can update the server firmware by downloading an update package and following the instructions on the Web page.

  • Page 64: Configuring Raid

    See “Using the Setup Utility program” on page 43. Note: If you cannot recover the BIOS after using the instructions in this topic, the BIOS read-only memory (ROM) might be damaged. You must replace the system board. Contact the Lenovo Customer Support Center.
  • Page 65 server as one single storage unit. Creating and using RAID arrays provides high performance, such as the expedited I/O performance, because several drives can be accessed simultaneously. RAID drive groups also improve data storage reliability and fault tolerance compared with single-drive storage systems.

  • Page 66: Configuring Raid Using The Lenovo Thinkserver Deployment Manager Program

    • Creates a RAID response file that can be used to configure RAID controllers on similarly configured Lenovo servers See “Lenovo ThinkServer Deployment Manager” on page 13 and view the help system from the main interface of the program. Configuring the advanced SATA or SAS hardware RAID Your server comes with a RAID adapter to provide advanced SATA or SAS hardware RAID functions.

  • Page 67: Updating The Firmware

    BIOS, the TSM firmware, and the FRU/SDR. To update the firmware, do one of the following: • Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to check for the latest level of firmware, such as the BIOS updates and device drivers.
  • Page 68 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 69: Chapter 6. Replacing Hardware

    • Before using the product, be sure to read and understand the multilingual safety instructions and the Lenovo Limited Warranty (LLW) on the documentation disc that comes with the product. Reading and understanding the safety instructions reduces the risk of personal injury and damage to your product.

  • Page 70: Handling Static-Sensitive Devices

    • If your server has air ducts or air baffles, do not remove them while the server is running. Operating the server without the air ducts or air baffles might cause the microprocessor(s) to overheat. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 71: Working Inside The Server With The Power On

    • For servers that support up to two microprocessors, ensure that the second microprocessor socket always contains a microprocessor or is protected by a microprocessor socket cover. Working inside the server with the power on when the halt, esult the loss when you inside the The server supports hot-swap devices and is designed to operate safely while it is turned on and the cover is...

  • Page 72: Installing, Removing, Or Replacing Hardware

    Notes: • Use only parts provided by Lenovo. • Depending on the model, your server might look slightly different from the illustrations in this topic. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 73: Removing And Reinstalling The Rack Handles

    The EMI integrity and cooling of the server are protected by having all drive bays and PCIe card slots covered or occupied. When you install an internal drive or a PCIe card, save the EMI shield or dummy tray from the drive bay or save the PCIe card slot bracket in case that you later remove the device. Attention: An unoccupied drive bay or PCIe card slot without a cover, shield, dummy tray, filler, or any other protection might impact the EMI integrity and cooling of the server, which might result in overheating or component damage.

  • Page 74: Removing And Reinstalling The Cooling Shroud

    2. Prepare your server. See “Removing or extending the server from the rack cabinet” on page 57. 3. Remove the server cover. See “Removing the server cover” on page 57. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 75 4. Insert a finger into each of the two holes in the cooling shroud and then lift the cooling shroud out of the server. Attention: For proper cooling and airflow, reinstall the cooling shroud before turning on the server. Operating the server for more than 30 minutes with the cooling shroud removed might damage server components.

  • Page 76: Installing Or Removing A Memory Module

    16 memory slots). For more information about the memory modules in your specific server model, use the Setup Utility program. See “Viewing information in the Setup Utility program” on page 43. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 77 For a list of supported ThinkServer memory module options, go to: http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server Before installing a memory module, ensure that you observe the following guidelines: • All memory modules to be installed must be the same type. Your server supports the following types of memory modules: –...
  • Page 78 The following table explains the memory module installation order for servers that have two microprocessors (CPU1 and CPU2) installed. Table 4. Memory module installation order in independent mode for servers with two microprocessors CPU1 DIMM CPU2 DIMM DIMM installation order ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 79 Memory module installation order in mirroring mode In mirroring mode, the server maintains two identical copies of all data in memory and the RAS features are available. For more information about the RAS features, refer to the related section in “Features” on page 7. Notes: •...

  • Page 80: Installing A Memory Module

    See “Memory module installation rules” on page 62. • Use any documentation that comes with the memory module and follow those instructions in addition to the instructions in this topic. To install a memory module, do the following: ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 81 1. Remove all external media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Prepare your server. See “Removing or extending the server from the rack cabinet” on page 57. 3.

  • Page 82: Removing A Memory Module

    5. Locate the memory slots on the system board and read the memory module installation rules. See “Memory module installation rules” on page 62. 6. Remove any parts or disconnect any cables that might prevent your access to the memory slots. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 83: Installing Or Removing The Thinkserver System Manager Premium Module

    Therefore, working as an integrated solution in your server, the TSM Premium provides an increased level of manageability over the basic server management available. You can purchase a TSM Premium module from Lenovo. For a list of ThinkServer options, go to: http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server...
  • Page 84 • If you remove the TSM Premium module, the iKVM function for server remote management will be unavailable. • Depending on the model, your server might look slightly different from the illustration in this topic. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 85: Installing Or Removing The Thinkserver Trusted Platform Module

    Trusted Computing Group (TCG) to provide a hardware method of data encryption. It stores passwords, encryption keys, and digital certificates to help provide security solutions and protect the server. You can purchase a TPM option from Lenovo. Installing the TPM...

  • Page 86: Removing The Tpm

    This topic provides instructions on how to remove the TPM if the server has one installed. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 87: Installing Or Removing The Raid 110I Upgrade Key

    SATA software RAID. As a result, the capability of the system board is expanded. You can purchase a RAID 110i key from Lenovo and install it to the RAID upgrade key connector on the system board. For a list of ThinkServer options, go to: http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server...
  • Page 88 • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 142. Removing the RAID 110i key your eading and page page ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 89: Installing Or Removing The Lenovo Thinkserver Raid 500 Or 520I Upgrade Key

    • To complete the removal procedure, go to “Completing the parts replacement” on page 142. Installing or removing the Lenovo ThinkServer RAID 500 or 520i upgrade The following two RAID upgrade keys activate RAID 5 and RAID 50 levels for advanced SATA or SAS...
  • Page 90 • Lenovo ThinkServer RAID 500 upgrade key (requires the Lenovo ThinkServer RAID 500 PCIe Adapter) • Lenovo ThinkServer RAID 520i upgrade key (requires the Lenovo ThinkServer RAID 520i PCIe Adapter) As a result, the capability of the installed ThinkServer RAID adapters is expanded. You can purchase a RAID upgrade key from Lenovo at: http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server...
  • Page 91 6. Locate the connector for the RAID 500 or 520i upgrade key on the Lenovo ThinkServer RAID 500 or 520i PCIe Adapter. Then, insert the RAID upgrade key into the connector. Ensure that the RAID upgrade key is securely seated.

  • Page 92: Installing Or Removing A Thunderbolt Memory Module

    MegaRAID SAS Software User Guide on the documentation disc that comes with your server. Installing or removing a Thunderbolt memory module This topic applies only to the Lenovo ThinkServer RAID 720i PCIe Adapter that supports the TMM. The following two types of TMM are available: •...
  • Page 93 4. Remove the Lenovo ThinkServer RAID 720i PCIe Adapter. See “Removing a PCIe card” on page 88. 5. Position the TMM above the Lenovo ThinkServer RAID 720i PCIe Adapter and align the two holes in the TMM with the two pins on the adapter. Then, lower the TMM straight down until it is securely seated.

  • Page 94: Installing Or Removing The Sd Module

    5. Press the two release tabs and lift the TMM straight up and out of the Lenovo ThinkServer RAID 720i PCIe Adapter. Figure 39. Removing the TMM 6. If you are instructed to return the old TMM, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
  • Page 95 3. Remove the server cover. See “Removing the server cover” on page 57. 4. Remove the riser card assembly 1. See “Replacing the riser card assembly” on page 133. 5. Locate the SD module connector on the system board. See “System board components” on page 33. Remove any parts and disconnect any cables that might impede your operation.

  • Page 96: Installing Or Removing The Thinkserver Raid Super Capacitor Module

    Installing or removing the ThinkServer RAID Super Capacitor Module The ThinkServer RAID Super Capacitor Module protects the cache memory on the installed ThinkServer RAID Adapter. You can purchase a ThinkServer RAID Super Capacitor Module from Lenovo. For a list of ThinkServer options, go to: http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server...
  • Page 97 Installing the ThinkServer RAID Super Capacitor Module your eading and page page Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • You can install two ThinkServer RAID Super Capacitor Modules in your server. •...
  • Page 98 2. Prepare your server. See “Removing or extending the server from the rack cabinet” on page 57. 3. Remove the server cover. See “Removing the server cover” on page 57. 4. Disconnect the cable of the ThinkServer RAID Super Capacitor Module from the RAID card. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 99: Installing Or Removing A Pcie Card

    5. Gently lift the plastic tab that secures the ThinkServer RAID Super Capacitor Module. Then, slide the ThinkServer RAID Super Capacitor Module as shown to completely remove it from the chassis. Figure 44. Removing the ThinkServer RAID Super Capacitor Module 6.
  • Page 100 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: The Lenovo ThinkServer RAID 520i PCIe Adapter and Lenovo ThinkServer RAID 720i PCIe Adapter only can be installed in PCIe slot 1.
  • Page 101 6. Remove the PCIe slot bracket from the riser card assembly. Store the bracket in case that you later remove the PCIe card and need the bracket to cover the place. Figure 47. Removing a PCIe slot bracket 7. Touch the static-protective package that contains the PCIe card to any unpainted surface on the outside of the server.

  • Page 102: Removing A Pcie Card

    3. Remove the server cover. See “Removing the server cover” on page 57. 4. Remove the riser card assembly and lay it upside down on a flat, clean, and static-protective surface. See “Replacing the riser card assembly” on page 133. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 103: Installing Or Removing The Optical Module

    5. Pivot the card latch to the open position. Figure 50. Pivoting the card latch to the open position 6. Grasp the PCIe card by its edges and carefully pull it out of the PCIe slot on the riser card assembly. Note: The PCIe card might fit tightly into the PCIe slot.
  • Page 104 Then, take the optical module out of the package. 3. With the optical module handle in the open position, insert the optical module into one of the two holes in the PCIe card. Figure 52. Installing the optical module ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 105 4. Pivot the optical module handle to the closed position to secure the optical module in place. Figure 53. Pivoting the optical module handle to the closed position What to do next: • To work with another piece of hardware, go to the appropriate section. •...
  • Page 106 What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Completing the parts replacement” on page 142. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 107: Installing Or Removing The Intrusion Switch

    Installing or removing the intrusion switch The intrusion switch informs you that the server cover is not properly installed or closed by creating an event in the system event log (SEL). You can purchase an intrusion switch from Lenovo. Installing the intrusion switch...
  • Page 108 Figure 57. Removing the intrusion switch 6. If you are instructed to return the old intrusion switch, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 109: Installing Or Replacing A Heat Sink

    • To work with another piece of hardware, go to the appropriate section. • To complete the removal procedure, go to “Completing the parts replacement” on page 142. Installing or replacing a heat sink your eading and page page Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
  • Page 110 9. Remove any protective cover that protects the thermal grease on the bottom of the new heat sink. Then, place the new heat sink on the system board so that the four screws on the new heat sink are aligned with the corresponding mounting studs on the system board. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 111: Installing Or Replacing The Microprocessor

    1 and the microprocessor socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option kit from Lenovo and install the second microprocessor to expand system capabilities.
  • Page 112 Note: There are two marks on the microprocessor retainer. Open the small handle marked with first and then open the other small handle marked with . Always follow the correct sequence when you open the small handles. Figure 60. Opening the handles ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 113 7. Gently press the microprocessor retainer to open it. Ensure that the small handles and the microprocessor retainer are in the fully open position. Note: Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible.
  • Page 114 Note: Do not remove the socket cover until you install a microprocessor into the socket. If you remove the microprocessor, install the socket cover or a new microprocessor immediately. Figure 64. Removing the microprocessor socket cover ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 115: Replacing The Microprocessor

    12. Close the microprocessor retainer. Then, close the small handle first and then close the small handle to lock the retainer into position and secure the new microprocessor in the socket. Note: There are two marks on the microprocessor retainer. Open the small handle marked with first and then open the other small handle marked with .
  • Page 116 Note: There are two marks on the microprocessor retainer. Open the small handle marked with first and then open the other small handle marked with . Always follow the correct sequence when you open the small handles. Figure 66. Opening the handles ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 117 7. Gently press the microprocessor retainer as shown to open it. Ensure that the small handles and the microprocessor retainer are in the fully open position. Figure 67. Opening the microprocessor retainer 8. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor socket.
  • Page 118 The new microprocessor is in the correct orientation when this indicator faces the beveled corner of the microprocessor socket. Figure 70. Installing the microprocessor ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 119 12. Close the microprocessor retainer. Close the small handle first. Then, close the small handle lock the retainer into position and secure the new microprocessor in the socket. Note: There are two marks on the microprocessor retainer. Ensure that you close the small handle marked with first and then close the small handle marked with .

  • Page 120: Installing Or Replacing A Hot-Swap Redundant Power Supply

    Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. To install a hot-swap redundant power supply, do the following: ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 121 1. Touch the static-protective package that contains the new hot-swap redundant power supply to any unpainted surface on the outside of the server. Then, take the new hot-swap redundant power supply out of the package. 2. If you are installing a power supply, locate the bay for the power supply in the rear of your server. Insert your index finger and thumb into the holes in the metal shield that protects the bay and pull the shield out of the chassis.
  • Page 122 To replace a hot-swap redundant power supply, do the following: 1. Locate the failing hot-swap redundant power supply in the rear of your server. Then, disconnect the power cord from the failing hot-swap redundant power supply. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 123: Installing Or Replacing A Hot-Swap Hard Disk Drive

    2. Press the tab inward and carefully pull the handle to slide the hot-swap redundant power supply out of the chassis. Note: Do not use too much force. You can first carefully slide the hot-swap redundant power supply a little bit out to release it from the secured position. Then, completely slide it out of the chassis. Figure 75.
  • Page 124 Figure 76. Opening the handle of a hard disk drive Figure 77. Opening the handle of a dummy hard-disk-drive tray ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 125 3. Pull the handle and carefully slide the hot-swap hard disk drive or the dummy tray out of the front of the chassis. Figure 78. Removing the hot-swap hard disk drive or the dummy tray 4. Touch the static-protective package that contains the new hot-swap hard disk drive to any unpainted surface on the outside of the server.

  • Page 126: Installing Or Replacing An Easy-Swap Storage Drive

    3. Prepare your server. See “Removing or extending the server from the rack cabinet” on page 57. 4. Locate the appropriate easy-swap-drive bay. See “Front view of the server” on page 17. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 127 5. Use a screwdriver to turn the handle lock to the unlocked position. The handle opens automatically. Figure 80. Opening the handle of the easy-swap drive or the dummy tray 6. Pull the handle and carefully slide the easy-swap drive or the dummy tray out of the front of the chassis. Figure 81.

  • Page 128: Installing Or Replacing A 2.5-Inch Drive

    • To configure RAID, go to “Configuring RAID” on page 50. Installing or replacing a 2.5-inch drive You can install or replace a 2.5-inch drive without turning off the server, which helps you avoid significant interruption to the operation of the system. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 129 For a list of ThinkServer drive options, go to: http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The number of the installed drives in your server varies depending on the server model. The vacant bays are occupied by dummy drive trays.
  • Page 130 4. Touch the static-protective package that contains the 2.5-inch drive to any unpainted surface on the outside of the server. Then, take the 2.5-inch drive out of the package. Note: Do not touch the circuit board on the drive. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 131 5. Position the 2.5-inch drive into the 3.5-inch to 2.5-inch drive adapter as shown in the following illustration. Figure 87. Positioning the 2.5-inch drive into the drive adapter 6. Align the two screw holes in the 2.5-inch drive with the corresponding holes in the drive adapter. Then, install the two screws to secure the 2.5-inch drive to the drive adapter.
  • Page 132 • To work with another piece of hardware, go to the appropriate section. • To configure RAID, go to “Configuring RAID” on page 50. • To complete the installation, go to “Completing the parts replacement” on page 142. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 133 Replacing a 2.5-inch drive from a 3.5-inch hard-disk-drive bay your eading and page page Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. To replace a 2.5-inch drive from a 3.5-inch hard-disk-drive bay, do the following: 1.
  • Page 134 Figure 93. Removing the screws that secure the 2.5-inch drive and the drive adapter 5. Remove the two screws that secure the 2.5-inch drive. Figure 94. Removing the screws that secure the 2.5-inch drive ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 135: Installing Or Replacing The Optical Drive

    6. Lift the 2.5-inch drive up to remove it from the drive adapter. Figure 95. Removing the 2.5-inch drive from the drive adapter 7. Install a new 2.5-inch drive. See “Installing a 2.5-inch drive into a 3.5-inch hard-disk-drive bay” on page 115.
  • Page 136 Then, take the new optical drive out of the package. 7. Slide the new optical drive into the drive bay from the front until it is secured by the release button ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 137 Figure 97. Installing the optical drive 8. Connect the connector to the rear of the optical drive. Figure 98. Connecting the connector to the rear of the optical drive 9. If necessary, connect the other end of the signal cable to the SATA connector for the optical drive on the system board.

  • Page 138: Connecting An External Tape Drive

    1. Remove all external media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 139 2. Prepare your server. See “Removing or extending the server from the rack cabinet” on page 57. 3. Remove the server cover. See “Removing the server cover” on page 57. 4. Remove the cooling shroud. See “Removing and reinstalling the cooling shroud” on page 60. 5.

  • Page 140: Replacing The Easy-Swap-Drive Module

    2. Prepare your server. See “Removing or extending the server from the rack cabinet” on page 57. 3. Remove the server cover. See “Removing the server cover” on page 57. 4. Remove the cooling shroud. See “Removing and reinstalling the cooling shroud” on page 60. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 141 5. Locate the easy-swap-drive module. See “Server components” on page 23. 6. Remove all the installed easy-swap storage drives and dummy trays (if any) from the hard-disk-drive bays. See “Installing or replacing an easy-swap storage drive” on page 112. 7. Disconnect the signal cable and power cable from the system board. 8.

  • Page 142: Replacing A System Fan

    3. Remove the server cover. See “Removing the server cover” on page 57. 4. Remove the cooling shroud. See “Removing and reinstalling the cooling shroud” on page 60. 5. Locate the system fans. See “Server components” on page 23. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 143: Replacing The Front Panel Board

    6. Disconnect the cable of the system fan from the system fan connector on the system board. Grasp the top of the system fan with your index finger and thumb and then lift the system fan out of the server. Figure 104.
  • Page 144 7. Touch the static-protective package that contains the new front panel board to any unpainted surface on the outside of the server. Then, take the new front panel board out of the package. Note: Carefully handle the front panel board by its edges. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 145: Replacing The Front Vga And Usb Module

    8. Carefully position the new front panel board so that the two screw holes in the new front panel board are aligned with the corresponding mounting studs on the chassis. Then, install the screws to secure the front panel board in place. Figure 107.
  • Page 146 7. Touch the static-protective package that contains the new front VGA and USB module to any unpainted surface on the outside of the server. Then, take the new module out of the package. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 147: Replacing The Riser Card Assembly

    8. Carefully position the new front VGA and USB module on the chassis. Ensure that the VGA and USB connectors are inserted into the corresponding holes in the front bezel. Align the screw hole in the new module with the corresponding mounting stud on the chassis. Then, install the screw to secure the module.
  • Page 148 Figure 111. Removing the riser card 8. Touch the static-protective package that contains the new riser card to any unpainted surface on the outside of the server. Then, remove the new riser card from the package. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 149: Replacing The Coin-Cell Battery

    9. Align the screw holes in the new riser card with the corresponding ones in the bracket. Then, install the two screws to secure the riser card to the bracket. Figure 112. Installing the riser card 10. Reinstall the PCIe card on the new riser card assembly. 11.
  • Page 150 In this case, you need to carefully lift the riser card assembly up so that you can access the coin-cell battery. You do not need to disconnect any cables from the riser card assembly or completely remove the riser card assembly. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 151: For Service Technician Only: Replacing The System Board

    5. Remove the old coin-cell battery. Figure 114. Removing the coin-cell battery 6. Install a new coin-cell battery. Figure 115. Installing the coin-cell battery 7. If you have lifted up the riser card assembly, reinstall it into the chassis. See “Replacing the riser card assembly”...
  • Page 152 11. Remove the SD module if one is installed. See “Removing the SD module” on page 81. 12. Remove the coin-cell battery. See “Replacing the coin-cell battery” on page 135. 13. Remove the heat sinks. See “Installing or replacing a heat sink” on page 95. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 153 14. Disconnect all cables from the system board. 15. Lift the release pin and the lifting handle to disengage the system board from the chassis. Then, move the system board to the front of the server and carefully pivot the system board upward to remove it out of the chassis.
  • Page 154 Figure 118. Applying the thermal grease to the top of the microprocessor 21. Install the heat sinks on the new system board. See “Installing or replacing a heat sink” on page 95. ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 155 22. Reinstall all parts that you have removed one by one in the reversed sequence as you remove them. Connect all cables to the new system board. Refer to the information that you have noted down and the related topics in “Installing, removing, or replacing hardware” on page 58. 23.

  • Page 156: Completing The Parts Replacement

    1. Start the Setup Utility program by pressing the F1 key, and then check the BIOS and BMC version. 2. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to download the latest version of firmware. Then, install the firmware to your server.

  • Page 157: Updating The Server Configuration

    Attention: To avoid component damage, connect the power cords last. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives.
  • Page 158 • To use the Lenovo ThinkServer Deployment Manager program, see “Lenovo ThinkServer Deployment Manager” on page 13. • To update your system firmware, see “Updating the firmware” on page 53. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 159: Chapter 7. Troubleshooting And Diagnostics

    6. View the system event log to diagnose problems. See “Viewing the system event log” on page 146. 7. Turn on the server and press Esc as soon as you see the logo screen to view any diagnostic messages. 8. Download and use a diagnostic program to diagnose problems. See “Lenovo ThinkServer Diagnostics” on page 14.

  • Page 160: Viewing The System Event Log

    • If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained service technician and must be performed only by a trained service technician. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 161: Storage Drive Problems

    Action Symptom The optical drive is not recognized. 1. Ensure that: • The related cables and connectors are not damaged and the connector pins are not bent. • The optical drive is securely connected to the correct SATA connector on the system board and the SATA connector is enabled in the Setup Utility program.

  • Page 162: Memory Module Problems

    • If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained service technician and must be performed only by a trained service technician. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 163: Keyboard, Mouse, And Usb Device Problems

    Action Symptom The amount of system memory that is displayed is less 1. Ensure that: than the total capacity of the installed physical memory • All memory modules are the correct type modules and you suspect a memory module problem. supported by the server.
  • Page 164 • The device drivers are installed correctly. • The USB controller is enabled in the Setup Utility program. See “Using the Setup Utility program” on page 43. 2. Restart the server. 3. Replace the USB device. ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 165: Chapter 8. Getting Information, Help, And Service

    Using the documentation Information about your Lenovo system and installed software, if any, or optional devices is available in the documentation that comes with the product. The documentation can include printed documents, online documents, readme files, and help files. Most of the documentation for your server is on the documentation disc provided with your server.

  • Page 166: Help And Service

    • Check the power switches to ensure that the system and optional devices are turned on. • Use the troubleshooting information in your system documentation on the documentation disc that comes with your product. • Check for the updated information, new device drivers, and hints and tips on the Lenovo Support Web site at: http://www.lenovo.com/support •...

  • Page 167: Using Other Services

    Service availability and service names might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.com...
  • Page 168 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 169: Appendix A. Notices

    Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.

  • Page 170: Trademarks

    Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.com/recycling...
  • Page 171 If the battery needs to be replaced, contact your place of purchase or contact Lenovo for service. If you need to dispose of a lithium battery, insulate it with vinyl tape, contact your place of purchase or a waste-disposal operator, and follow their instructions.

  • Page 172: Requirement For Batteries Containing Perchlorate

    A Lenovo possui um canal especí fico para auxiliá-lo no descarte desses produtos. Caso você possua um produto Lenovo em situaç ão de descarte, ligue para o nosso SAC ou encaminhe um e-mail para: reciclar@lenovo.com, informando o modelo, número de série e cidade, a fim de enviarmos as instruç ões para o correto descarte do seu produto Lenovo.

  • Page 173: Important Weee Information

    For additional WEEE information, go to: http://www.lenovo.com/recycling WEEE information for Hungary Lenovo, as a producer, bears the cost incurred in connection with the fulfillment of Lenovo’s obligations under Hungary Law No. 197/2014 (VIII.1.) subsections (1)-(5) of section 12. Appendix A. Notices...

  • Page 174: Restriction Of Hazardous Substances (Rohs) Directive

    Restriction of Hazardous Substances (RoHS) Directive This topic provides statements about the Restriction of Hazardous Substances (RoHS) Directive. The latest environmental information is available at http://www.lenovo.com/ecodeclaration. China RoHS ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 175: Turkish Rohs

    Turkish RoHS The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Waste Electrical and Electronic Equipment (WEEE). India RoHS RoHS compliant as per E-Waste (Management & Handling) Rules, 2011.
  • Page 176 Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Lenovo is not responsible for any radio or television interference caused by using other than specified or recommended cables and connectors or by unauthorized changes or modifications to this equipment.
  • Page 177 Geräte der Klasse A. Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo (Deutschland) GmbH, Meitnerstr. 9, D-70563 Stuttgart. Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A.

  • Page 178: Eurasian Compliance Mark

    Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation. Some models of the following machine types have been designed and tested to conform to the ENERGY STAR program requirement for computer servers at the time of manufacture: 70D6, 70D7, 70D8, 70D9, 70QK, 70QL, 70QM, and 70QN.
  • Page 179 Lenovo encourages you to make efficient use of energy an integral part of your day-to-day operations. To help in this endeavor, set the following power-management features to take effect when your servers have been used: • Processor- or core-reduced power states •...
  • Page 180 ThinkServer RD350G User Guide and Hardware Maintenance Manual...

  • Page 181: Index

    161 Boot Manager menu external tape drive Setup Utility program connect cable connection 39 features coin-cell battery Lenovo ThinkServer Deployment Manager program 13 replacing 135 firmware configuring updating 53 server 43 flashing configuring RAID the BIOS 49...
  • Page 182 121 interface Setup Utility program 43 internal drives optical drive features 8 installing or replacing 121 intrusion switch optical module installing installing removing removing 91 option completing the replacement ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 183 RAID 500 or 520i upgrade key 77 locations 17, 19 SD module software server cover Lenovo ThinkServer Deployment Manager 13 ThinkServer RAID Super Capacitor Module 82, 84 specifications starting ThinkServer Trusted Platform Module Setup Utility program 43 TSM Premium module 70...
  • Page 184 LEDs 145 system event log 146 troubleshooting procedure TSM Premium module installing removing 70 TSM Settings menu Setup Utility program 45 turning off the server 41 turning on the server TÜV gloss statement ThinkServer RD350G User Guide and Hardware Maintenance Manual...
  • Page 186 Lenovo.

Table of Contents