Download Print this page

Sealey PP4.V2 Instructions

Ultrasonic leak detector

Advertisement

Quick Links

Thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Instruction
manual
1.
SAFETY INSTRUCTIONS
1.1.
GENERAL SAFETY INSTRUCTIONS
1.1.
Familiarise yourself with the application, limitations and potential hazards of the tester. Also refer to the vehicle manufacturer's hand
book.
1.2.
Ensure that the tester is in good condition before use.
1.3.
Only use recommended attachments and parts. To use unapproved items may be dangerous and will invalidate your warranty.
1.4.
If the tester receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
1.5.
Keep children and unauthorised persons away from the work area.
DO NOT disassemble the tester for any reason. The tester must only be checked by qualified service personnel.
WARNING! To avoid damaging hearing, DO NOT set headphones volume too high.
DO NOT drop the detector or transmitter.
DO NOT tamper with the electronic circuit boards within the dectector or transmitter.
DO NOT use the tester outdoors, or in damp, or wet locations and DO NOT use in the vicinity of flammable liquids or gases.
DO NOT use the dectector or transmitter near any electrical appliances which emit electromagnetic waves, as this will give a false
reading.
DO NOT use the tester for a task for which it is not designed.
1.6.
When not in use, store the tester carefully in a safe, dry, childproof location.
1.7.
If the dectector and transmitter are not to be used for long periods, remove the batteries before storing.
2. INTRODUCTION & SPECIFICATION
Quick and simple location of air, water or dust leaks. Place the transmitter in the vehicle and close the doors and windows. Trace the detector
around outside of the screen, windows and door seals to locate the leak. Includes adjustable headphones for detector. Transmitter and
detector powered by 9V batteries. supplied in carry-case.
Operating Conditions:
Frequency Response:
Output Frequency:
Battery:
Size:
Weight:
© Jack sealey limited
InsTRuCTIOns FOR:
ULTRASONIC LEAk DETECTOR
mOdEl no:
Detector
0°C ~ 40°C <80% RH
0°C ~ 40°C <80% RH
40kHz +/- 2kHz
-
9V
192 x 50 x 30mm
80 x 56 x 27.5mm
115g (incl battery)
75g (incl battery)
Original Language Version
PP4.V2
Transmitter
-
40kHz
9V
PP4.V2 Issue no: 3(I) - 14/03/16

Advertisement

loading

Summary of Contents for Sealey PP4.V2

  • Page 1 PP4.V2 mOdEl no: Thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 3.2.3. scan the the outside of the compartment with the detector. Any leaks from the compartment can be easily detected and pinpointed. 3.2.4. When the check is completed remove and turn off the transmitter. Sensitivity Control fig.2 Headphones Volume Control fig.3 fig.4 fig.1 Original Language Version PP4.V2 Issue no: 3(I) - 14/03/16 © Jack sealey limited...
  • Page 3 Contact your local solid waste authority for recycling information. Battery Regulations under the Waste Batteries and Accumulators Regulations 2009, Jack sealey ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme.