Page 2
Computer Entertainment Inc. is strictly prohibited. Commercial use or Rental pro- according to the manufacturer's instruction. hibited. This service manual is the proprietary property of Sony Computer Enter- tainment Inc.. It's use is authorized person who work for PlayStation 2 only.
Page 3
LABEL, MODEL CAUTION for static electricity NUMBER For disassemble and assemble the console, Don' t charge static electricity on your body and around equipment. Get rid static electricity by grounding your body and around equipment. Static electricity will be destroyed key devives like ICs, OPT and etc. TAPE, VOID...
Page 5
COVER, SCREW CAUTION When tighten the BV316 and M354 screws, Tighten them in order to the steps shown figure. BV316 SCREW (2 LOCK), +BV TAPPING M354 SCREW (M3 X 54), HEAD TAPPING M354 M354 Step 7 BV316 Step 6 Step 8 Step 5 Step 4 BV316...
Page 10
COVER ASSY,LOWER CAUTION For exchanging the LOWER COVER ASSY. to new one, Check the carved seal on surface of LOWER COVER ASSY. CABLE, FLAT (FFC-011) CABLE, FLAT (FFC-012)
POWER BLOCK CAUTION Use of controls or adjustments or performance of procedures other thn those specified herein may result in hazardous radiation exposure. P360 P360 SCREW +P 3 X 6 Harness from SWITCH, POWER (WITH AC INLET) CAUTION The components identified by mark dotted line with mark.
Page 13
SHEET, INSULATING CAUTION Never lose the fitting of INSULATING SHEET put on the SHIELD(B) when assemble the console. LABEL, CUTION, BARRIER CAUTION for SCPH-30001 Never lose the fitting of LABELs put on the SHIELD(B) when assemble the console. Harness from FAN CAUTION The components identified by mark dotted line with mark.
SWITCH, POWER (WITH AC INLET) CAUTION The components identified by mark dotted line with mark. are critical for safety. Replace only with part number specified.
Page 16
SHIELD B B265 B265 TAPPING (B2 X 6.5) B265 M225 VIEW A M225 0 PART-NO.3 MAIN M2 X 2.5 VIEW B VIEW VIEW TOOLS : SCREW DRIVER ( #0)
Page 17
SHEET (DRIVER), ELECRIC HEAT IC802 Never lose the fitting of SHEET(DRIVER), ELECTRIC HEAT put on the IC802 and IC803 when assemble the console. IC803...
Page 18
CABLE, FLAT (FFC-011) CABLE, FLAT VIEW A (FFC-012) FFC from OPT HARNESS (HS-059) FFC from Spindle motor GH010 MOUNT FFC from OPT CN801 CN302 CN801 CN302 CN402 CN803 VIEW A FFC from Sled motor CN804 CN406 Pattern side down CN802 (RED) CN406 CN806...
BATTERY, LITHIUM CAUTION (CR2032 TYPE) For dumping the consumed CR2032 Lithium battery, Obey your countly law Standard procedures. GB003 GB-003/-004 MOUNT GB003 BACK CAUTION The components identified by mark dotted line with mark. are critical for safety. Replace only with part number specified.
Page 23
MD BLOCK ASSY CAUTION PULLEY BRACKET change to new one by repaier LABEL has to put on new PULLEY BRACKET due LABEL, CAUTION to in your country law and standart procedure for safty. LABEL, LASER CAUTION : for SCPH-30001D : for SCPH-30002D/30003D/30004D...
Page 24
TAPPING (B2 X 6.5) CAUTION Don't touch the place surrounded square shown figure when tighten screws. PULLEY, BRACKET ASSY TOOLS : SCREW DRIVER ( #0)
PWB, FLEXIBLE TOP SIDE VIEW SHAFT, MAIN RACK SCREW, SKEW 0 PLATE 3 MAIN M2 X 3.2 BOTTOM SIDE VIEW DEVICE, OPTICAL KHS-400B Insert FLEXIBLE PWB. to connector correctly and Lock the stopper surely not to FLEXIBLE PWB. pull out. Don't touch the adjustment resistor.