Philips US2-VOX120 User Manual

Bluetooth Headset

VOX 120
User Manual
/ (
1. On Off S1
.
2 Volume Up (S2)
.
3 Volume Down S3
4. Status Light
5. DC Socket
.
6 Speaker
.
7 Knuckle Joint
.
8 Microphone
.
9 Ear hook
!
Charging the battery
Thank you for buying new VOX 120 Bluetooth Headset. Before first time use, it
is important to charge the battery for 12 hours.
!
Turning on the Headset
While the Headset is powered down, press and hold S1 for 2 seconds. A low
tone followed by a high tone will indicate that the Headset is powered up. The
status light will be green for 1 second. Afterward, the status light will flash
green every 3 seconds.
!
Turning off the Headset
While the Headset is powered up, press and hold S1 for 5 seconds. A high tone
followed by a low tone will indicate that the Headset is powered down. And the
status light will be red until S1 is released.
!
Putting Headset in Pairing Mode
Make sure the Headset is fully charged and charging cable disconnected from it
before pairing starts. While the Headset is powered off, press and hold S1 for 4
seconds. The status light will flash alternately green and red to indicate that the
Headset is in Pairing Mode.
Follow the operating instructions for your Bluetooth mobile phone to start the
pairing process. Typically, this has to be done by going to a setup or connect
menu and then selecting the options to detect Bluetooth devices.
may take several seconds to establish a connection.
"
Your phone s display should indicate that it has found the '
headset and ask if you want to pair it. You should confirm this. The phone s
display would prompt you for a passkey or PIN. Enter a sequence of
.
and confirm
The Headset status light will flash green every 3 seconds, indicating successful
pairing. Probably the phone will also ask whether you want to change the
'
headset s name. We recommend you should approve the VOX 120 name and
not change it.
If pairing does not work as expected, turn the headset and phone off and wait
for 10 seconds. Turn the headset and phone on again and repeat all steps
from beginning.
!
Answering Incoming Calls
When an incoming call is present, the Headset will ring . Pressing S1 will
answer the call. The status light will flash fast while the call is in progress.
(once every second)
!
Transferring Calls (For Nokia 3650 or equivalent models)
When you are in session, calls can be transferred from the
the Headset and from the Headset to the Bluetooth
To transfer a call from the Bluetooth phone to the Headset: press S1 once, the
call will be transferred to the Headset.
To transfer a call from Headset to the Bluetooth
operating instructions of your phone.
!
Muting the microphone
To mute the microphone during an active call
Pressing both S2 and S3 buttons simultaneously for about a
microphone will be muted. A periodic beep tone will be heard while the mute
function is active.
To end the mute function
When the microphone is muted, press on both S2 and S3 buttons
simultaneously will end the mute function and the periodic beep tone will stop.
!
Ending Calls
While a call is in session on the Headset pressing S1 will disconnect the call.
After the call is disconnected, the status light will flash every 3 seconds
To reject a call (this function will only be supported by some mobile phones,
e.g. Nokia 3650 or Siemens S55)
When the Headset rings, press and hold S1 until you hear a long beep tone.
!
To make a new call using voice dialing
Requires a Bluetooth mobile phone with Voice Dialing function
1.Make sure the voice dialing function is enabled in the mobile phone and the
mobile phone is within the range of the Headset. Press S1 on the Headset
shortly.
2.After you hear the beep tone in the Headset, make a voice dial as you
normally would by saying the name of the contact as set up in the memory of
the mobile phone. The call will be connected in a few seconds.
!
Redialing last dialed number
(this function will only be supported by some
mobile phones, e.g. Nokia 3650 or Siemens S55)
To redial the last dialed number, press and hold S3 for 2 seconds. short low
tones will indicate an attempt to redial.
! Adjusting Speaker Volume
)
While a call is in session, repeatedly pressing and releasing S2 will
increase the speaker volume and repeatedly pressing and releasing S3
( )
will decrease the speaker volume on the Headset There is a key tone to
.
indicate volume increase or decrease However
heard when the volume level reaches its maximum or minimum
! Right or left ear
If you want to wear the Headset on your right ear, you have to change the
orientation of the ear hook.
Left ear orientation
1) Pull the ear hook upward from
the knuckle joint and flip the
hook 180 degrees.
Bluetooth
! Bend the ear hook to
Warning
fit your ear
Don't pull the ear hook side way over
"
VOX 120
its limit, it will break the ear hook joint.
'
" "
0000
! How to wear
Bluetooth phone to
phone.
phone, please follow the
1. Put on the headset with the ear hook behind your ear.
2. Bend the ear hook gently to fit your ear.
3. Make sure the microphone is pointing towards your mouth.
!
Low-battery indication
The status light will flash red instead of green when the battery is low.
second, the
There will also be a short beep every few minutes. When the battery level is
too low , the Headset will automatically power off. It cannot be powered on
again unless the charger is connected or the battery is charged
minutes .
!
Battery recharging
To recharge the battery, connect the charger cable to the Headset. During
recharging, the status light shows a steady red light if the headset is turned off
but the red light will dim once every 3 seconds while the headset is on.
!
Fully charged indication
A steady green status light indicates that the headset is off and is fully charged.
Green light dimming once every 3 seconds indicates that the headset is on and
fully charged.
Headset
Turn
on
Turn
off
Disclaimer:
-
Talk time and stand by time of the VO
depending on mobile phone model being used
.
,
a warning tone will be
.
Right ear orientation
! Charging Connection Diagrams
(1) A/C charging
2) Put the ear hook back to the
knuckle joint and pull it down
firmly.
Accessories Table
:
NOTE
,
BQB CE and FCC approved
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
guarantee that interference will not occur in a particular installation.
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
-
-
-
-
for at least 5
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
Headset under
uncontrolled environment. This equipment should be installed and operated with
Fully charged
charging
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
Red LED Green LED
antenna or transmitter.
dim once every 3 sec dim once every 3 sec
Red LED on Green LED on
X 120 Bluetooth Headset will vary
Do not allow the product to come into contact with liquid. Do not open it.
Electric, Magnetic and Electromagnetic Fields ("EMF")
1. Philips Royal Electronics manufactures and sells many products targeted
2. One of Philips' leading Business Principles is to take all necessary health
3. Philips is committed to develop, produce and market products that cause
4. Philips confirms that if its products are handled properly for their intended
ins
AC Ma
5. Philips plays an active role in the development of international EMF and
pto r
AC Ada
Conformity
The Declaration of conformity is available on www.p4c.philips.com.
Maintenance and service
On line help: www.p4c.philips.com
Description
A / C Adaptor
.
Federal Communication Commission Interference Statement
However, there is no
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Health and safety
at consumers, which, like any electronic apparatus, in general have the
ability to emit and receive electro magnetic signals.
and safety measures for our products, to comply with all applicable legal
requirements and to stay well within the EMF standards applicable at the
time of producing the products.
no adverse health effects.
use, they are safe to use according to scientific evidence available today.
safety standards, enabling Philips to anticipate further developments in
standardization for early integration in its products.
If this