Advertisement
Handling instructions
Cordless Work Light
WARNING
○ Be careful of electrical shock.
○ When not in use or during inspection and
maintenance, be sure to turn the switch OFF
on the unit, and remove the battery from it.
○ Do not cover the work light with cloth,
cardboards or other materials when the light
is on. Doing so may result in fi re.
CAUTION
○ Do not use any other than the specifi ed
batteries.
○ Do not look at the LED light directly.
○ The LED cover will remain at a high
temperature when alight and immediately
after use, so do not touch it.
○ Be sure to turn the switch OFF when not using.
○ Do not expose the work light to rain.
○ Do not shock or disassemble the work light.
○ Do not allow the work light to contact gasoline, thinner etc.
○ Do not leave the work light in a car or the like that tends to be exposed to be searching
heat of the sun (above 60 °C). Otherwise, troubles can result.
SYMBOL
WARNING
The following show symbols used for the machine. Be sure that you understand their
meaning before use.
Read all safety warnings and all instructions.
SPECIFICATIONS
LED
Dimensions (without battery)
Weight (without battery)
Operating time (Approx.): Using full charged Battery
Battery
BSL1840 BSL1830 BSL1820 BSL1815 BSL1440 BSL1430 BSL1420 BSL1415
[High/Low]
5.0 / 11.5 3.5 / 8.5 2.5 / 6.0 2.0 / 4.0 3.5 / 7.5 2.5 / 5.5 2.0 / 4.0 1.5 / 3.0
mode
(h)
Keep for future reference
UB 18DGL
Top handle
Switch
LED light
(built-in)
1/4-inch
screw hole
Fig. 1
18 W (0.5 W × 36 Pcs.)
256 mm (width) × 198 mm (length) × 252 mm (height)
0.74 kg
HOW TO USE
1. Battery insert/removal
Insert the battery in direction A until it
clicks. To remove, extract it in direction B
while holding down the latch. (Fig. 2)
2. Turning on the light
Press the switch to turn on the light.
The light setting will alternate between
[Strong], [Weak] and [Off ] whenever the
Strap hole
switch is pressed.
3. Light angle adjustment
The angle of the light can be adjusted within a range
Pipe hook
of approximately 120 degrees both upward and
downward. (Fig. 3)
4. Installation
In addition to placing it directly onto the fl oor or other
fl at surface, the unit can also be installed as follows.
⦁ Attached to a tripod with the use of a 1/4-inch screw. (Fig. 4)
Bottom handle
⦁ Suspended from a pipe with the use of the pipe hook. (Fig. 5)
⦁ Hung on the wall with the use of the wall-hanging hook. (Fig. 6)
CAUTION
○ There are cases in which it will not be possible to turn
on the light owing to a function to prevent the batteries
from over-discharging. IN this event, either replace the
batteries or recharge them.
○ Use cord or a similar article to fi x the unit in place to
prevent it from falling.
NOTE
Make sure the instruction manuals supplied with the
separately-purchased rechargers and batteries are read
thoroughly prior to use.
4
3
2
1
Battery (sold separately)
Latch
Item
No.
1
HEXGON HEAD TAPPING SCREW D4×12
2
FRONT CABINET
3
LENS
6
4
PCB
5
5
TAPPING SCREW D3×8
6
MAIN BODY
Hitachi Koki Co., Ltd.
120°
A
B
120°
Fig. 2
Fig. 3
1/4-inch screw hole
Fig. 4
Fig. 5
Wall-hanging hook Bottom handle
Fig. 6
Part Name
Q'TY
4
1
1
1
6
1
Code No. C99210821 NA
Advertisement
