Page 1 TOSHIBA 6100 Portable Personal Computer User’s Manual...
Page 2 © 2002 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.
Page 3 WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripher- als or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port,...
Page 4: Fcc Conditions
Irvine, California 92618-1697 Telephone: (949) 583-3000 TOSHIBA declares, that the product: PS610* conforms to the following Standards: Supplementary Information: This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Page 5 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 6: Region Selection
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made.
Page 7 FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 8 Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other...
Page 9 NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termina- tion on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Page 10 Notes for use of this device in New Zealand The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
Page 11 ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers.
Page 12: General Conditions
General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.
Page 13 TOSHIBA DVD-ROM drive SD-C2502** safety instruction ** means any letters or numbers. CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
Page 14 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
Page 15 TOSHIBA CD-RW/DVD-ROM drive SD-R2102** safety instruction ** means any letters or numbers. CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
Page 16 MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE. MANUFACTURED: TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME MINATO-KU, TOKYO 105-8001, JAPAN CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
Page 17 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på...
Page 18 Matsushita CD-R/RW drive UJDA340** safety instruction ** means any letters or numbers. CAUTIONS: 1. The CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
Page 19 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
Page 20 Matsushita CD-RW/DVD-ROM drive UJDA720** safety instruction ** means any letters or numbers. CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
Page 21 Location of the required label Location of the required label CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Kyushu Matsushita Electric Co., Ltd. 1-62 4-Chome Minoshima, Hakata-Ku Fukuoka,Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1...
Page 22 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på...
Page 23 TEAC DVD-ROM drive DV-28E** safety instruction ** means any letters or numbers. This product has been designed and manufactured according to FDA regulations "title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968," and is classified as a class 1 laser product.
Page 24 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
Page 25 TEAC CD-ROM drive CD-224E** safety instruction ** means any letters or numbers. This product has been designed and manufactured according to FDA regulations "title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968," and is classified as a class 1 laser product.
Page 26 Type Manufacturer Laser output Wavelength Location of the required label Optical pickup : PU-2200 : TEAC CORPORATION : Less than 0.25m W on the objective lens : 795nm THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.
Page 27 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING VORSICHT: Dieses Gerät enthält ein Laser-System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf.
Page 28 TEAC CD-R/RW drive CD-W28E** safety instruction ** means any letters or numbers. This product has been designed and manufactured according to FDA regulations "title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968," and is classified as a class 1 laser product.
Page 29 Location of the required label CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE. MANUFACTURED: Manufactured by TEAC Corporation 3-7-3 Naka-cho, Musashino-shi, Tokyo, Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
Page 30 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
Page 31 TEAC CD-RW/DVD-ROM drive DW-28E** safety instruction ** means any letters or numbers. This product has been designed and manufactured according to FDA regulations "title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968," and is classified as a class 1 laser product.
Page 32 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
Page 33 HITACHI DVD-ROM drive GDR-8081N** safety instruction ** means any letters or numbers. CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
Page 34 Location of the required label CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT DATE OF MANU- FACTURE. MANUFACTURED: Hitachi-LG Data Storage, Inc. 26-5, TORANOMON 1-CHOME, MINATO-KU, TOKYO, 105-0001 JAPAN CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER...
Page 35 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
Page 37: Table Of Contents
Table of Contents Preface Manual contents ... xliii Conventions ... xliv Abbreviations ... xliv Icons ... xliv Keys ... xliv Key operation ... xlv Display ... xlv Messages ... xlv General Precautions Stress injury ... xlvii Heat injury ... xlvii Pressure or impact damage ...
Page 38 Slim Select Bay modules ... 2-11 DVD-ROM drive (Black) ... 2-12 CD-ROM drive (Black) ... 2-13 CD-R/RW drive (Black) ... 2-13 CD-RW/DVD-ROM drive (Black) ... 2-14 Slim Select Bay HDD adaptor (Black) ... 2-16 Slim Select Bay 2nd battery pack (Black) ... 2-16 Weight saver ...
Page 39 Using 3 1/2" external diskette drive ... 4-10 Connecting 3 1/2" diskette drive ... 4-11 Disconnecting 3 1/2" diskette drive ... 4-12 Diskette care ... 4-12 Wireless communications ... 4-13 Wireless LAN ... 4-13 Bluetooth wireless technology ... 4-13 Wireless communication switch ... 4-14 Wireless communication LED ...
Page 40 Chapter 6 Power and Power-Up Modes Power conditions ... 6-1 Power indicators ... 6-4 Battery indicators ... 6-4 DC IN indicator ... 6-4 Power indicator ... 6-5 Battery types ... 6-5 Main battery ... 6-5 Secondary battery (option) ... 6-6 Real time clock battery ...
Page 41 Slim Select Bay 2nd battery pack (Black) ... 8-10 Installing ... 8-10 Removing ... 8-10 Additional AC adaptor ... 8-11 Battery charger ... 8-11 Slim Select Bay HDD adaptor (Black) ... 8-11 USB diskette drive ... 8-13 Advanced Port Replicator ... 8-13 Parallel printer ...
Page 42 Modem ... 9-21 Standby/Hibernation ... 9-22 Memory expansion ... 9-23 LAN ... 9-23 Wireless LAN ... 9-24 Bluetooth ... 9-24 TOSHIBA support ... 9-25 Before you call ... 9-25 Where to write ... 9-25 Appendixes Appendix A Specifications ... A-1 Appendix B Display Controller and Modes ...B-1...
Page 43: Preface
This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your 6100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 44: Conventions
User's Manual Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available.
Page 45: Key Operation
Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Page 46 User's Manual xlvi...
Page 47: General Precautions
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 48 User's Manual xlviii...
Page 49: Chapter 1 Introduction
Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use. Check to make sure you have all the following items: Satellite Pro 6100 Portable Personal Computer Universal AC adaptor and power cord Modular cable Blue spare AccuPoint II (pointing device) cap...
Page 50 • SPANworks 2000 Professional • TOSHIBA Console • Online manual Documentation: • Satellite Pro 6100 Portable Personal Computer User’s Manual • Microsoft Windows XP Professional manual package • Instruction Manual for Safety & Comfort • International Limited Warranty (ILW) Instruction (This instruction is included only with computers sold in ILW supported areas.)
Page 51: Features
If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complemen- tary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorpo-...
Page 52 User's Manual Disks Hard disk drive The computer has an integrated, 2 1/2" hard disk drive (HDD) for nonvolatile storage of data and software. It comes in the following sizes. • 15 billion bytes (14.06 GB) • 20 billion bytes (18.63 GB) •...
Page 53 CD-RW/DVD-ROM Some models are equipped with a full-size, CD-RW/ drive (Black) DVD-ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maxi- mum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 8 speed and CD-RW at up to 8 speed. A Mode Control switch turns power to the CD-RW/DVD- ROM drive on and off so you can use the drive as a stand- alone audio CD player.
Page 54 User's Manual RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage between 100 and 240 volts.
Page 55: Slim Select Bay 2Nd Battery Pack (Black)
Multimedia Sound System Sound Blaster™ Pro™ and Windows Sound System compatible sound system provides internal speaker as well as jacks for an external microphone and headphone. It also has a volume control dial. Video-out jack This RCA jack lets you transfer NTSC or PAL data to external devices.
Page 56: Special Features
Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
Page 57 System automatic This feature automatically turns off power to the system power off when there is no input for a time specified. You can specify the time in the When the system standby time has passed item of the System Power Mode window in Power Saver. Battery save mode This feature lets you save battery power.
Page 58: Utilities
This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme files. TOSHIBA Power Saver To access this power savings management program in Windows 2000, open the Control Panel and double-click the TOSHIBA Power Saver icon.
Page 59 Settings and click Control Panel. In the Control Panel, double-click the Mouse icon. TOSHIBA Accessibility This utility lets you make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. The Fn key remains active until another key is pressed.
Page 60: Options
PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™ (IEEE1394) port, line-in jack and line-out jack. NOTE: The Satellite Pro 6100 does not support the DVI and i.LINK ports on the Advanced Port Replicator. 1-12...
Page 61 Slim Select Bay options The following modules can be installed in the Slim Select Bay. The user can select either a CD-ROM drive, a DVD-ROM drive, a CD-R/RW drive, a CD-RW/DVD-ROM drive , a Slim Select Bay HDD adaptor or a Slim Select Bay 2nd battery pack to be preinstalled as a standard device.
Page 62 User's Manual 1-14...
Page 63: Chapter 2 The Grand Tour
The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. ISPLAY LATCH ICROPHONE EADPHONE...
Page 64: Left Side
User's Manual Infrared port This infrared port is compatible with Infrared Data Associa- tion (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 Kbps, 57.6 Kbps, 38.4 Kbps, 19.2 Kbps or 9.6 Kbps data transfer with IrDA 1.1 compatible external devices.
Page 65: Right Side
Slim Select Bay A CD-ROM drive, DVD-ROM drive, CD-R/RW drive, CD- RW/DVD-ROM drive, Slim Select Bay HDD adaptor, Slim Select Bay 2nd battery pack can be installed in the Slim Select Bay. A weight saver can be installed when there is no module.
Page 66: Back Side
User's Manual Back side Figure 2-4 shows the computer’s back side. AN VENT DC IN 15V XTERNAL MONITOR PORT Figure 2-4 The computer’s back side DC IN 15V The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using DC IN 15V the wrong adaptor can damage your computer.
Page 67: Underside
LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, Ether 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). LAN indicator This indicator glows green when the computer is accessing the LAN.
Page 68 The 6, Power and Power-Up Modes, describes how to access the battery pack. Additional battery packs can be pur- chased from your TOSHIBA dealer to extend the computer’s battery operating time. Battery pack lock Slide this lock to release or secure the battery pack.
Page 69: Front With The Display Open
Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle. ISPLAY SCREEN ENSOR SWITCH...
Page 70: Indicators
User's Manual AccuPoint II A pointer control device located in the center of the keyboard is used to control the on-screen pointer. Refer to the AccuPoint II section in Chapter 4, AccuPoint II Control buttons below the keyboard let you select menu control buttons items or manipulate text and graphics designated by the on- screen pointer.
Page 71 Indicators Power source/system indicators DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunc- tions, this indicator flashes orange. Power The Power indicator glows green when the computer is on.
Page 72 User's Manual The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you enter numbers. When the F11 key indicator glows the keypad overlay lets you control the cursor. UMERIC MODE RROW MODE Figure 2-8 Keypad overlay indicators...
Page 73: Ac Adaptor
Power and Power-Up Modes Figure 2-10 The AC adaptor CAUTION: Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. The current rating for the computer is 5.0 amperes. Slim Select Bay modules...
Page 74: Dvd-Rom Drive (Black)
User's Manual DVD-ROM drive (Black) An optional full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") digital video disk/compact disk without using an adaptor. It may be selected as a standard component or as an option. NOTE: The read speed is slower at the center of a disk and faster at the outer edge.
Page 75: Cd-Rom Drive (Black)
DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly. Code Region Canada, United States Japan, Europe, South Africa, Middle East Southeast Asia, East Asia Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean...
Page 76: Cd-Rw/Dvd-Rom Drive (Black)
User's Manual CD, CD-R read 24 speed (maximum) CD-RW read 14 speed (maximum) CD-R write 8 speed (maximum) CD-RW write 8 speed (maximum) This drive supports the following formats: • Photo CD • CD-ROM • CD-DA • CD-ROM x A Mode 2 (Form1, Form2) •...
Page 77 This drive supports the following formats: • DVD-ROM • Photo CD • CD-ROM • CD-DA • CD-ROM x A Mode 2 (Form1, Form2) • Enhanced CD (CD-EXTRA) CD-R describes compact disks that can be written only once. The recorded data cannot be erased or changed.
Page 78: Slim Select Bay Hdd Adaptor (Black)
User's Manual Slim Select Bay HDD adaptor (Black) You can increase your computer’s data storage capacity by installing an optional, integrated, 2 1/2" HDD in the Slim Select Bay. ELEASE LATCH Figure 2-12 The Slim Select Bay HDD adaptor Slim Select Bay 2nd battery pack (Black) An optional battery pack can be installed in the Slim Select Bay to increase the computer’s battery power and operating time.
Page 79: Weight Saver
Slim Select Bay modules Weight saver Installing a weight saver module in the Slim Select Bay lets you reduce the carrying weight of the computer. Figure 2-14 The weight saver 2-17...
Page 80 User's Manual 2-18...
Page 81: Chapter 3 Getting Started
Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 82: Setting Up Your Work Space
User's Manual Setting up your work space Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
Page 83: Seating And Posture
Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices. Allow adequate space behind the computer to let you freely adjust the display. The display should be angled to reduce glare and maximize visibility.
Page 84: Lighting
User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.
Page 85: Opening The Display
Chapter 6, Power and Power-Up CAUTION: Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. The current rating for the computer is 5.0 amperes. Connecting the AC adaptor...
Page 86 User's Manual 1. Connect the power cord to the AC adaptor. Figure 3-3 Connecting the power cord to the AC adaptor 2. Connect the AC adaptor’s DC output plug to the DC IN port on the back side of the computer. Figure 3-4 Connecting the adaptor to the computer 3.
Page 87: Turning On The Power
Turning on the power This section describes how to turn on the power. NOTE: After you turn on the power for the first time, do not turn it off until you have set up the operating system (OS) and the OS has started 1.
Page 88: Windows Xp Professional/2000 Setup
Follow the on-screen directions. If you ordered Windows 2000, the operating system is not preinstalled. Follow the steps below to install the Windows 2000 and TOSHIBA utilities. 1. Turn on the computer, load the Product Recovery CD-ROM in the drive and turn off the power.
Page 89: Hibernation Mode
NOTE: For the computer to shut down in hibernation mode, the hiberna- tion feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.
Page 90: Starting Hibernation
2. a. In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. b. In Windows 2000, double-click the TOSHIBA Power Saver icon. 3. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button.
Page 91: Standby Mode
Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Built-in HDD indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices.
Page 92 In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. b. In Windows 2000, double-click the TOSHIBA Power Saver icon. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility described in the Control Panel.
Page 93: Restarting The Computer
Restarting the computer Certain conditions require that you restart the computer system. For example, if: You change certain computer settings. An error occurs and the computer does not respond to your keyboard commands. There are two ways to restart the computer system: 1.
Page 94 User's Manual 2. Hold down the C key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the C key. NOTE: When you install additional software components, a window similar to the one below will be shown while the software is being decompressed.
Page 95: Chapter 4 Operating Basics
Operating Basics This chapter gives information on basic operations including using the AccuPoint II, optical media drives, the external diskette drive, the internal modem, the LAN and changing Slim Select Bay modules. It also provides tips on caring for your computer and heat dispersal.
Page 96: Accupoint Ii Precautions
User's Manual AccuPoint II precautions Certain conditions can affect the on-screen pointer when using AccuPoint II. For example, the pointer may travel contrary to AccuPoint II operation or an error message may appear, if You touch the AccuPoint II during power-up. You apply constant, soft pressure during power-up.
Page 97: Changing Slim Select Bay Modules
Changing Slim Select Bay modules This section explains how to change modules in the Slim Select Bay. The illustra- tions show replacement of the DVD-ROM drive with the Slim Select Bay HDD adaptor. Therefore, the text refers to those modules. However, the procedures are the same for any of the modules: DVD-ROM drive, CD-ROM drive, CD-R/RW drive, CD-RW/DVD-ROM drive or optional Slim Select Bay 2nd battery pack with separate tray.
Page 98: Installing A Module
User's Manual Installing a module Install the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2. If you want to lock the Slim Select Bay module, set the screw of the Slim Select Bay lock in the back hole.
Page 99: Loading Cds
CD-R/RW drive (Black) Read CD, CD-R 24-speed (maximum) CD-RW 14-speed (maximum) Write CD-R 8-speed (maximum) CD-RW 8-speed (maximum) CD-RW/DVD-ROM drive (Black) Read 24-speed (maximum) 8-speed (maximum) Write CD-R 8-speed (maximum) CD-RW 8-speed (maximum) Loading CDs To load CDs, follow the steps below and refer to figures 4-5 to 4-9. 1.
Page 100 User's Manual b. Pressing the eject button will not open the drawer when the computer’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Page 101 4. Lay the CD, label side up, in the drawer. NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD tray. Therefore, you will need to turn the CD at an angle when you place it in the tray. After seating the CD, however, make sure it lies flat, as shown in figure 4-8.
Page 102: Removing Cds
User's Manual 6. Push the center of the drawer to close it. Press gently until it locks into place. CAUTION: If the CD is not seated properly when the drawer is closed, the CD might be damaged. Also, the drawer might not open fully when you press the eject button.
Page 103: Cd/Dvds Care
2. There are indentations on the sides of the drawer to let you grasp the CD. Hold it gently and lift it out. NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD tray. Therefore, you will need to turn the CD at an angle when you remove it.
Page 104: Using 3 1/2" External Diskette Drive
User's Manual 5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs. 6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/ DVD.
Page 105: Connecting 3 1/2" Diskette Drive
NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 2. Do not set anything on top of the diskette drive. 3. If you need to boot the computer from the diskette drive or if you use an OS that does not support USB, you must set the USB-FDD Legacy Emulation feature in HW Setup to Enabled.
Page 106: Disconnecting 3 1/2" Diskette Drive
User's Manual Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive.
Page 107: Wireless Communications
Wireless communications The computer’s wireless communication function supports both wireless LAN and Bluetooth devices. Wireless LAN The wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with IEEE 802.11 wireless LAN standard (Revision B).
Page 108: Wireless Communication Switch
User's Manual Security Two advanced security mechanisms ensure a high level of security: Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. Encryption prevents eavesdropping and maintains link privacy. Wireless communication switch You can enable or disable wireless LAN and Bluetooth functions, with the on/off switch.
Page 109: Lan
LAN circuits support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled. NOTE: Wake-up on LAN does not work without the AC adaptor.
Page 110: Disconnecting Lan Cable
User's Manual 2. Plug one end of the cable into the LAN’s jack. Press gently until you hear the latch click into place. Figure 4-13 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub.
Page 111 Using the switch To select a network device, follow the steps below. 1. a. In Windows XP, click start, point to All Programs, click Network Device Switch. b. In Windows 2000, click start, point to Programs, click Network Device Switch. 2.
Page 112: Super Long Life Scheme
4. The computer resumes operation in suspend or hibernation mode. Super Long Life scheme The Super Long Life mode is a scheme of the TOSHIBA Power Saver utility. It is designed to maximize battery operating time. In the default setting, wired and wireless LAN functions are disabled. To enable LAN functions, clear the Control device power management checkbox.
Page 113: Using The Internal Modem
1. a. In Windows XP, click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. NOTE: Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 114: Properties Menu
User's Manual Figure 4-17 The Region Selection icon (Windows 2000) 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.
Page 115: Modem Selection
Setting You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region.
Page 116: Connecting
User's Manual Connecting To connect the internal modem cable, follow the steps below. CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2. Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Page 117: Cleaning The Computer
Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 118: Heat Dispersal
Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Fan item of the Power Save Mode window in TOSHIBA Power Saver. When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.
Page 119: Chapter 5 The Keyboard
The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s key- board layout your computer is configured with.
Page 120: F1 ... F12 Function Keys
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 121 Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter, Ctrl and Alt keys to the right of the main keyboard.
Page 122: Hotkeys
User's Manual Hotkeys Hotkeys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hotkeys, the current setting will be displayed as an icon. Instant security: Press Fn + F1 to lock the keyboard and blank the screen to prevent others from accessing your data.
Page 123 Hibernation: When you press Fn + F4, the computer can enter Hibernation. To avoid entering Hibernation unexpectedly, a dialog box appears for verification. However, if you check the checkbox in the dialog box, it will not appear from the next time.
Page 124: Emulating Fn Key On External Keyboard
Fn key equivalent. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. Windows special keys...
Page 125: Turning On The Overlays
Keypad overlay Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode indicator lights. Now try cursor and page control using the keys shown in figure 5-2. Press Fn + F10 again to turn off the overlay.
Page 126: Temporarily Using Normal Keyboard (Overlay On)
User's Manual Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.
Page 127: Generating Ascii Characters
Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
Page 128 User's Manual 5-10...
Page 129: Chapter 6 Power And Power-Up Modes
Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 130 User's Manual Table 6-1 Power conditions continued 2nd battery • Operates adaptor fully • LED: 2nd battery green connected charged 2nd battery • Operates partially • Quick charge * charged • LED: 2nd battery orange or no charge • Operates 2nd battery •...
Page 131 Table 6-1 Power conditions continued 2nd battery • Operates adaptor charge • LED: 2nd battery off is above connected low battery trigger point 2nd battery • Operates charge • LED: 2nd battery is below low battery trigger point 2nd battery Computer goes charge is into resume mode...
Page 132: Power Indicators
User's Manual Power indicators The Main battery, Slim Select Bay, DC IN and Power indicators on the system indicator panel alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Main battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the secondary battery.
Page 133: Power Indicator
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. The main battery recharges the RTC batteries. The main battery maintains the state of the computer when you enable Resume.
Page 134: Secondary Battery (Option)
Check system. Then press [F1] key ..CAUTION: The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
Page 135: Safety Precautions
Safety precautions 1. Turn off the computer’s power immediately and disconnect the power cord from the power socket, if the battery pack produces an odor, overheats or changes color or shape while it is being used or charged. Carefully remove the battery pack from the computer.
Page 136 The Battery indicator glows orange when the battery is being charged. CAUTION: Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Do not attempt to charge the battery pack with any other charger.
Page 137: Monitoring Battery Capacity
2. Plug in the AC adaptor. 3. Charge the battery until the Battery indicator glows green. Repeat the steps two or three times until the battery recovers normal capacity. Monitoring battery capacity Remaining battery power can be monitored in the Power Save Modes window in Power Saver of Windows.
Page 138: Retaining Data With Power Off
User's Manual How often and how long you use the hard disk and the diskette drive. How much charge the battery contained to begin with. How you use optional devices, such as a PC card, to which the battery supplies power. Enabling Resume mode conserves battery power if you are frequently turning the computer off and on.
Page 139: Replacing The Battery Pack
4. Connect the AC adaptor to the computer and the power cord to a power outlet. The DC IN LED should glow green, and the Battery LED should glow orange to indicate that the battery pack is being charged. If the DC IN indicator does not glow, power is not being supplied.
Page 140: Installing The Battery Pack
6. Slide the battery release latch to free the battery pack for removal. 7. Pull the battery pack forward to remove it. CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. ATTERY PACK LOCK...
Page 141: Starting The Computer By Password
2. Insert the battery pack. Figure 6-2 Installing the battery pack 3. Secure the battery pack lock. Starting the computer by password If you registered a user password, you must enter it to start the computer. For more information about how to set a password, refer to Chapter 7, Passwords.
Page 142 User's Manual 6-14...
Page 143: Chapter 7 Hw Setup And Passwords
HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for pointing devices, display, CPU, boot priority, keyboard, USB, LAN, general, password, device config and parallel/printer.
Page 144: Hw Setup Window
User's Manual HW Setup window The HW Setup window contains the following tabs: Pointing Devices, Display, CPU, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer. Figure 7-1 HW Setup window (Windows XP)
Page 145 HW Setup Figure 7-2 HW Setup window (Windows 2000) There are also three buttons: OK, Cancel and Apply. Accepts your changes and closes the HW Setup window. Closes the window without accepting your changes. Cancel Accepts all your changes without closing the HW Setup Apply window.
Page 146 User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory settings. Default Display the HW Setup version.. About Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on.
Page 147 4. If character strings match, the password is registered and the display changes Registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2.
Page 148: Device Config
User's Manual Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control. (Default) Setup by OS Parallel/Printer This tab lets you set the Printer Port Type. Use the Windows Device Manager to make settings for the Parallel port.
Page 149 Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you set the display to be used when the computer is booted. Selects an external monitor if one is connected. Other- Auto-Selected wise, it selects the internal LCD.
Page 150: Boot Priority
User's Manual Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD - > - > - > - > - > FDD - > - > - > - > - > CD-ROM(- > - > - > - > - > LAN) The computer looks for bootable files in FDD - >...
Page 151 NOTES: 1. PC card HDD boot is supported only by slot 0 on the computer. Support is guaranteed only for TOSHIBA PC card HDDs. 2. When you assign a PC card HDD top priority, “PC” is not displayed. However, the PC card HDD takes the position of HDD in the Boot Priority Options list above.
Page 152 User's Manual HDD Priority Options This option lets you set the boot priority for the HDD if more than one is installed in the computer. Built-in HDD -> -> -> -> -> Second HDD Second HDD -> -> Built-in HDD ->...
Page 153 USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.
Page 154: Supervisor Password
User's Manual Supervisor password Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file. 7-12...
Page 155: Chapter 8 Optional Devices
Optional Devices Optional devices can expand the computer’s capabilities and its versatility. The following optional devices are available from your TOSHIBA dealer: Cards/memory PC cards SD cards Memory expansion Power devices Additional battery pack (Black) Slim Select Bay 2nd battery pack (Black)
Page 156: Pc Cards
5 mm Type II cards or one 10.5 mm Type III card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 157: Removing A Pc Card
3. Check the configuration in the HW Setup window to make sure it is appropri- ate for your card. 4. Slide the PC card lock into the locked position. CARD LOCK Figure 8-2 Locking the PC card Removing a PC card To remove the PC card, follow the steps below.
Page 158: Sd Cards
User’s Manual 5. Grasp the PC card and remove it. CARD Figure 8-3 Removing the PC card SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with capacities of 8 MB, 16 MB, 32 MB, 64 MB and 128 MB.
Page 159: Installing An Sd Card
Installing an SD card To install an SD card, follow the steps below. 1. Insert the SD card. 2. Press gently to ensure a firm connection. CARD Figure 8-4 Inserting an SD card CAUTION: Make sure the SD card is oriented properly before you insert Removing an SD card To remove an SD card, follow the steps below.
Page 160: Memory Expansion
User’s Manual 3. Grasp the card and remove it. CARD INDICATOR CARD Figure 8-5 Removing an SD card CAUTION: Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card.
Page 161 2. Do not try to install a memory module with the computer turned on or turned off in Standby and Hibernation mode. You can damage the computer and the memory module. 3. If you install a memory module that is not compatible with the computer, a beep will sound when you turn on the power.
Page 162: Removing Memory Module
User’s Manual 7. Push the module down so that it lies flat and is secured by two latches. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Figure 8-7 Inserting the memory module 8.
Page 163: Additional Battery Pack (Black)
3. Remove two screws securing the memory module cover. 4. Lift off the cover. 5. Use a slender object such as a pen to press two latches on either side of the memory module to the outside. The memory module will pop up. 6.
Page 164: Installing
User’s Manual Slim Select Bay 2nd battery pack (Black) You can install a secondary battery pack (PA3129*) in the computer’s Slim Select Bay. The battery comes with an adaptor. For details on using the adaptor, follow the steps below. For details on installing modules in the Slim Select Bay, refer to Chapter 4, Operating Basics.
Page 165 Slim Select Bay HDD adaptor (Black) 2. Push the secondary battery pack up from the bottom and lift it out. Figure 8-10 Removing the secondary battery pack from the adaptor Additional AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load: PA3083*.
Page 166 User’s Manual To install an HDD in the Slim Select Bay HDD adaptor (PA3134U-1ETC) follow the steps below. 1. Slide the lock to the unlock position and open the lid. Figure 8-11 Opening the lid 2. Insert the HDD and push forward to ensure a firm connection. Figure 8-12 Installing the HDD 8-12...
Page 167 3. Close the lid and slide the lock to the lock position. Figure 8-13 Closing the lid For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating USB diskette drive The 3 1/2"...
Page 168 DVI port (This port is not supported by the computer.) NOTES: 1. When a Port Replicator is connected to the computer, remove all cables connected to the computer. 2. The Satellite Pro 6100 does not support the DVI and i.LINK ports on the Port Replicator. Parallel printer You can connect any standard Centronics-compatible parallel printer to your computer.
Page 169: External Monitor
7. Turn on the computer. 8. Start the Hardware Setup program. Refer to Chapter 7 words. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect.
Page 170: Ps/2 Mouse
User’s Manual To change the display settings, press Fn + F5. If you disconnect the monitor before you turn the computer off, be sure to press Fn + F5 to switch to the internal display. Refer to Chapter 5, the display setting. NOTE: If you set Simultaneous for the computer’s display, you must set the computer’s display resolution to the same as that of the external monitor or other device, such as a projector.
Page 171: Ps/2 Keyboard
NOTES: 1. How the computer treats the connection to a PS/2 mouse depends on the setting for Pointing Devices under the HW Setup program. If Simultaneous is selected, you can operate both the AccuPoint II and the PS/2 mouse. If Auto-Selected is chosen, the AccuPoint II is disabled when a PS/2 mouse is connected.
Page 172: Security Lock
User’s Manual Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
Page 173: Preliminary Checklist
Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 174 User's Manual Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.
Page 175: Hardware And System Checklist
Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals. Basic problems may occur in the following areas: System start-up Self test Power Password Keyboard LCD panel Hard disk drive CD-ROM drive (Black) CD-R/RW drive (Black) DVD-ROM drive (Black) CD-RW/DVD-ROM drive (Black) Diskette drive...
Page 176: Self Test
When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. IIf the self test is successful, the computer tries to load the operating system.
Page 177: Overheating Power Down
Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally enter Hibernation or Resume mode and shut down. Problem Procedure Computer shuts down Leave the computer off until the DC IN indicator and DC IN indicator stops blinking.
Page 178 User's Manual Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the com- puter, contact your dealer.
Page 179: Password
Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated. Check the Battery indicator.
Page 180: Keyboard
User's Manual Keyboard Keyboard problems can be caused by your setup configuration. For more informa- tion refer to Chapter 5, The Keyboard Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected. Press Fn + F10 and try typing again. Output to screen Make sure the software you are using is not is garbled...
Page 181: Hard Disk Drive
Hard disk drive Problem Procedure Computer does not Check if a diskette is in the diskette drive. If a boot from hard disk diskette is inserted, remove it and reboot. drive There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented.
Page 182: Cd-R/Rw Drive (Black)
User's Manual A foreign object in the drawer could block laser light from reading the CD. Make sure there is no ob- struction. Remove any foreign object. Check whether the CD is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner.
Page 183: Dvd-Rom Drive (Black)
A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner.
Page 184 User's Manual A foreign object in the drawer could block laser light from reading the DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner.
Page 185: Cd-Rw/Dvd-Rom Drive (Black)
DVD does not play Some video discs might not play properly in a correctly in an Expansion Station. Play the disc in the optional Expansion DVD-ROM drive installed in the computer. Station If problems persist, contact your dealer. CD-RW/DVD-ROM drive (Black) For more information, refer to Chapter 4, Problem Procedure...
Page 186: Diskette Drive
User's Manual Check the type of DVD/CD you are using. The drive supports: DVD-ROM: CD-ROM: Check the region code on the DVD. It must match that on the DVD drive. Region codes are listed in the The Grand Tour . If problems persist, contact your dealer.
Page 187: Infrared Port
Infrared port Refer also to the documentation for your IrDA compatible device and related software. Problem Procedure Infrared devices do Check that the device is connected to an not work as expected electric outlet. Make sure the outlet is supplying power by plugging in an appliance.
Page 188: Pointing Device
User's Manual Make sure your software is configured to recog- nize the printer. Check your printer and software documentation. Printer error Check your printer documentation. If problems persist, contact your dealer. Pointing device If you are using a PS/2 mouse, also refer to Chapter 8, your mouse documentation.
Page 189: Pc Card
Is your software configured to recognize the mouse? Check the software documentation. If problems persist, contact your dealer. Serial mouse This section applies only with Windows XP operating systems. You cannot use a serial mouse with Windows 2000. Problem Procedure On-screen pointer Check for a firm connection between the does not respond to...
Page 190: Sd Card
User's Manual SD card Refer also to Chapter 8, Optional Problem Procedure SD card Reseat the SD card to make sure it is firmly error occurs connected. Check the card’s documentation. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Problem Procedure...
Page 191: Sound System
Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/ O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected...
Page 192: Usb
User's Manual Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, NOTE: If you turn the computer off in Resume mode while the display is on TV, the computer will select either the internal LCD or an external computer CRT as the display device.
Page 193: Modem
Modem Refer to the online help files for Problem Procedure Communication Make sure the computer’s internal modem software can’t settings are correct. Refer to Phone and Modem initialize modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make sure the communication application’s tone dial a call...
Page 194: Standby/Hibernation
User's Manual A CONNECT display Check the error control setting in your is quickly replaced by NO CARRIER You can also use the AT\N command. Refer to the online help files for Appendix C, mands. Character display In data transmission, make sure the parity bit becomes garbled and stop bit settings correspond with those during a...
Page 195: Memory Expansion
Memory expansion Refer also to Chapter 8, Optional modules. Problem Procedure Beep sounds. Make sure the memory module installed in the (If slot A two beeps, expansion slot is compatible with the computer. If slot B three beeps, If an incompatible module has been installed, If both two and three follow the steps below.
Page 196: Wireless Lan
User's Manual Wireless LAN If the following procedures do not restore LAN access, consult your LAN adminis- trator. For more information on wireless communication, refer to Chapter 4, Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on.
Page 197: Toshiba Support
TOSHIBA support If you require any additional help using your computer or if you are having prob- lems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 198 User's Manual Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R 8H2 Singapore TOSHIBA Singapore Pte. Ltd. 438B Alexandra Road #06-01...
Page 199: Appendix A Specifications
Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 330 (w) x 289 (d) x 34.8/37.1 (h) millimeters (does not include the thicker part of the bottom of the computer) Weight CD/DVD DVD-ROM CD-RW/DVD-ROM * Weight will vary depending on whether or not and what kind of options are adopted.
Page 200 User's Manual Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: system...
Page 201: Display Controller And Modes
Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA), Extended Graphics Array (XGA), Super Extended Graphics Array (SXGA), Super Extended Graphics Array Plus (SXGA+) and Ultra Extended Graphics Array (UXGA) support for the internal LCD and external monitors.
Page 202: Video Modes
User's Manual Video modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
Page 203 Table Video modes continued Video Type Resolution mode 320 x 200 Grph Pels 640 x 200 Grph Pels 640 x 350 Grph Pels 640 x 350 Grph Pels 640 x 480 Grph Pels 640 x 480 Grph Pels 320 x 200 Grph Pels SVGA 640 x 480...
Page 204 User's Manual Table Video modes continued Video Type Resolution mode SVGA 1400 x 1050 Grph Pels* SVGA 1600 x 1200 Grph Pels SVGA 1920 x 1440 Grph Pels SVGA 2048 x 1536 Grph Pels SVGA 640 x 480 Grph Pels SVGA 800 x 600 Grph Pels...
Page 205 Table Video modes continued Video Type Resolution mode SVGA 1600 x 1200 Grph Pels SVGA 1920 x 1440 Grph Pels SVGA 2048 x 1536 Grph Pels SVGA 640 x 480 Grph Pels SVGA 800 x 600 Grph Pels SVGA 1024 x 768 Grph Pels SVGA 1280 x 1024...
Page 206 User's Manual Table Video modes continued Video Type Resolution mode SVGA 1920 x 1440 Grph Pels SVGA 2048 x 1536 Grph Pels * This mode is supported on SXGA+ LCD only. NOTE: Some video modes are not supported with the Multimonitor feature and Different Refresh rate mode.
Page 207: At Commands
AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT command, and n is the specific value for that command.
Page 208 User's Manual Answer command This command instructs the modem to go off-hook and answer an incoming call. Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default).
Page 209 Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while...
Page 210 User's Manual Monitor speaker volume This command sets speaker volume to low, medium, or high. Low volume. Low volume. (Same as L0) Medium volume (default). High volume. Result Codes: n=0,1,2,3 ERROR Otherwise Monitor speaker mode This command turns the speaker on or off. The speaker is off.
Page 211 Result Codes: n=0,1 ERROR Otherwise Return on-line to data mode Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). This command issues a retrain before returning to on-line data mode. This command issues a rate renegotiation before returning to on-line data mode.
Page 212 User's Manual Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
Page 213 Enable Enable Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
Page 214 User's Manual &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default).
Page 215 &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.
Page 216 User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.
Page 217 Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. Buffer mode. No error control. Direct mode. MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects.
Page 218 User's Manual Protocol result code Disable protocol result code appended to DCE speed. Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 ERROR Otherwise View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed.
Page 219: Appendix D S-Registers
S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
Page 220 User's Manual Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.
Page 221 Response formatting character (user defined) This register determines the ASCII value used as the line feed charac- ter. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII Command line editing character (user defined)
Page 222 User's Manual Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (an- swer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction.
Page 223 Dial line rate S37 = 0 (default) S37 = 1 S37 = 2 S37 = 3 S37 = 4 S37 = 5 S37 = 6 S37 = 7 S37 = 8 S37 = 9 S37 = 10 S37 = 11 S37 = 12 S37 = 13 S37 = 14...
Page 224 User's Manual AT command set result codes The following table shows the result codes. The result code summary Result Code CONNECT RING NO CARRIER ERROR CONNECT 1200 EC* NO DIAL TONE BUSY NO ANSWER CONNECT 2400 EC* CONNECT 4800 EC* CONNECT 9600 EC* CONNECT 14400 EC* CONNECT 19200 EC*...
Page 225 Result Code DELAYED* BLACKLISTED* BLACKLIST FULL* *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
Page 226 User's Manual...
Page 227 V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 228 User's Manual Table E-1 Result codes for a V.90 connection No. Result code CONNECT 32000 EC* Connection at 32000 bits/s CONNECT 36000 EC* Connection at 36000 bits/s CONNECT 40000 EC* Connection at 40000 bits/s CONNECT 44000 EC* Connection at 44000 bits/s CONNECT 48000 EC* Connection at 48000 bits/s CONNECT 52000 EC* Connection at 52000 bits/s CONNECT 56000 EC* Connection at 56000 bits/s...
Page 229 AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.90 enabled: automatic speed selection - maximum modem speed (default) Appendix E...
Page 230 User's Manual...
Page 231: Appendix F Wireless Lan
Expand the capabilities of your Wireless LAN Access Points, to support Wireless devices that have been equipped with Wireless LAN card. NOTE: The internal Wireless LAN card can’t be used with the TOSHIBA Wireless LAN PC card. Appendix F...
Page 232 User’s Manual Peer-to-peer workgroup The peer-to-peer workgroup configuration enables you to quickly set up a small Wireless workgroup, where the workgroup participants can exchange files using features such as Files and Printer Sharing as supported by Microsoft Networking. Figure F-1 Peer-to-peer Wireless workgroup You can use this option to set up a temporary or ad-hoc network in environment where no access points are available, for example in Small Office/Home Office (SOHO) environments.
Page 233 Appendix F Enterprise networking Figure F-2 Stand-alone Wireless LAN With the Wireless LAN Access Points you can connect to a corporate Local Area Network (LAN) infrastructure to have Wireless access to all network facilities. LAN Infrastructures may either be. Stand-alone Wireless LANs as pictured in Figure F-2...
Page 234: Easy Configuration
User’s Manual Wireless network infrastructures connected to an existing Ethernet network as pictured in Figure F-3. Figure F-3 LAN Infrastructure Easy configuration The Wireless LAN card functions like any standard wired Ethernet card except it gives you the freedom of Wireless connections. Where an Ethernet card requires a cable connection to a hub and/or patch panel, the cable physically limits the location of the wired connection.
Page 235 Wireless LAN card features The TOSHIBA Wireless LAN mini-PCI card is a Wireless network card that fits into a mini-PCI Type IIIA slot. Wireless LAN card types The Wireless LAN card is a Wireless network card that complies with the IEEE 802.11 standard on Wireless LANs (Revision B).
Page 236: Card Specifications
User’s Manual Card specifications Table F-1 Physical specifications Form Factor Mini-PCI TypeIIIA Dimensions Weight Temperature and Humidity Operation 0 to 55 C Transit -20 to 70 C Storage -10 to 60 C Although the card may still operate in the range of –20 to 70 C, operation outside the range of 0 to 55 C may no longer be according to specifications.
Page 237: Radio Characteristics
Protocol Acknowledgment (ACK) Data Rate High Medium Standard 2 Mb/s The cards use an automatic Transmit Rate Select mechanism. Radio characteristics Radio characteristics of Wireless LAN cards may vary according to: Country/region where the product was purchased Type of product Wireless communication is often subject to local radio regulations.
Page 238 NOTE: The range values listed in Table F-4 are typical distances as measured at the TOSHIBA Wireless LAN laboratories. These values provide rule-of-thumb guides. They may vary according to the actual radio conditions at the location where the Wireless LAN product is installed.
Page 239 Subject to the radio regulations that apply in your country/region, your Wireless LAN card may support a different set of 2.4 GHz channels (see Table F-5). Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region.
Page 240 User’s Manual F-10...
Page 241: Ac Power Cord And Connectors
AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Wire size: Current rating:...
Page 242: Usa And Canada
User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada UL approved CSA approved Australia AS approved United Kingdom BS approved Europe Approved by the appropriate agency...
Page 243: Internal Modem Guide
Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the modem board NOTE: The internal modem is preinstalled. The following is for informa- tion only.
Page 244: Removing The Modem Board
User’s Manual Removing the modem board To remove the internal modem. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC adaptor and any other peripheral devices. 3. Turn the computer upside down and remove the battery pack. 4.
Page 245: Appendix I Parts Numbers
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules, communication devices and VRAM.
Page 246 PPENDIX...
Page 247: Glossary
Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CMOS: complementary metal-oxide...
Page 248 Association VGA: video graphics array VRM: video ready modem VRT: voltage reduction technology AccuPoint: A pointing device inte- grated into the TOSHIBA computer keyboard. adapter: A device that provides an interface between two dissimilar electronic devices. For example, the AC adapter modifies the power from a wall outlet for use by the computer.
Page 249 asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. AUTOEXEC.BAT: A batch file that executes a series of MS-DOS commands and programs each time you start the computer.
Page 250: Cache Memory
cache memory cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
Page 251 compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 252 device driver device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Page 253 See hard disk. floppy disk: See diskette. floppy disk drive (FDD): See diskette drive. Fn-esse: A TOSHIBA utility that lets you assign functions to hotkeys. format: The process of readying a blank disk for its first use. Formatting estab-...
Page 254 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 255 keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmitted code is, in turn, representative of the (ASCII) character marked on the key.
Page 256 monitor monitor: A device that uses rows and columns of pixels to display alphanu- meric characters or graphic images. See CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions.
Page 257 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
Page 258 restart restart: Resetting a computer without turning it off (also called ‘warm boot’ or ‘soft reset’). To restart the computer, press Ctrl + Alt + Del while the computer is on. See also boot. RCA jack: A single-pin connector that carries composite video signals, which include both contrast and color information.
Page 259 S-video: This connection provides separate lines for contrast and color, which produces a video image superior to that produced by a composite connection. See also RCA jack. synchronous: Having a constant time interval between successive bits, characters or events. system disk: A disk that has been formatted with an operating system.
Page 260 Glossary-14...
Page 261: Index
Index AC adaptor 1-6, 2-11 DC IN 15V port 2-4 additional 1-12, 8-11 connecting 3-5 AccuPoint II 1-5, 2-7 problems 9-16 using 4-1 Advanced Port Replicator 1-12, 8-13 ASCII characters 5-9 Auto power on, See Power Battery, See also Battery pack charging 6-8 extending life 6-10 indicator 2-8, 6-4...
Page 262 User's Manual Environment 3-2 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2 Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansion memory, See Memory expansion Fn key emulation 5-6 Fn + Alt (enhanced keyboard simula- tion) 5-3 Fn + Ctrl (enhanced keyboard simula- tion) 5-3 Fn + Enter 5-3...
Page 263 Keyboard 1-5, 5-1 emulating enhanced keyboard 5-2 F1 . . . F12 function keys 5-2 problems 9-8 PS/2 8-17 Typewriter keys 5-1 Keypad overlay 1-8, 5-6 arrow mode 5-7 numeric mode 5-7 temporarily changing modes 5-8 temporarily using normal keyboard (overlay on) 5-8 temporarily using overlay (overlay off) 5-8...
Page 264 PS/2 mouse 9-16 SD card 9-18 self test 9-4 serial mouse 9-17 sound system 9-19 standby/hibernation 9-22 support from TOSHIBA 9-25 system start-up 9-3 TV output signal 9-19 USB 9-20 Wireless LAN 9-24 Processor 1-3 Real time clock battery, See Battery...
Page 265 1-6, 2-1 problems 9-19 speaker 2-7 volume control 2-2 Standby 1-9 Standby/Hibernation problems 9-22 System auto off 1-9 TOSHIBA Power Saver 1-10 Troubleshooting, See Problems TV 8-16 Utilities list 1-10 USB 1-6 location 2-4 problems 9-20 Video modes, Appendix B...
Page 266 User's Manual Index-6...

This manual is also suitable for:

Satellite pro 6100 Ps610

Toshiba 6100 User Manual

Preface

Manual Contents

Conventions

General Precautions

Stress Injury

Heat Injury

Pressure or Impact Damage

PC Card Overheating

Chapter 1 Introduction

Equipment Checklist

Features

Slim Select Bay 2Nd Battery Pack (Black)

Special Features

Utilities

Options

Chapter 2 The Grand Tour

Front with the Display Closed

Left Side

Right Side

Back Side

Underside

Front with the Display Open

Indicators

Slim Select Bay Modules

AC Adaptor

Chapter 3 Getting Started

Setting up Your Work Space

Opening the Display

Connecting the AC Adaptor

Turning on the Power

Windows XP Professional/2000 Setup

Turning off the Power

Restarting the Computer

Restoring the Windows System

Chapter 4 Operating Basics

Using Accupoint II

Changing Slim Select Bay Modules

Using Optical Media Drives

Using 3 1/2" External Diskette Drive

Wireless Communications

Lan

Using the Internal Modem

Cleaning the Computer

Moving the Computer

Heat Dispersal

Chapter 5 The Keyboard

Typewriter Keys

F1 ... F12 Function Keys

Soft Keys: Fn Key Combinations

Windows Special Keys

Keypad Overlay

Generating ASCII Characters

Chapter 6 Power and Power-Up Modes

Power Conditions

Power Indicators

Battery Types

Care and Use of the Battery Pack

Replacing the Battery Pack

Starting the Computer by Password

Chapter 7 HW Setup and Passwords

HW Setup

Supervisor Password

Chapter 8 Optional Devices

PC Cards

SD Cards

Memory Expansion

Additional Battery Pack (Black)

External Monitor

PS/2 Mouse

PS/2 Keyboard

Security Lock

Chapter 9 Troubleshooting

Hardware and System Checklist

TOSHIBA Support

Appendix A Specifications

Appendix B

Display Controller and Modes

Appendix C

AT Commands