Sealey MCL500 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear safety
instructions footwear
1. SAFETY
WARNING! Ensure that the motorcycle is adequately secured to the lifting platform with appropriate straps before raising the
‰
load.
Maintain the lift in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use a qualified person to lubricate and maintain the lift. DO NOT use brake fluid to top up hydraulic unit.
9
Locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
9
lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike. DO NOT
operate the lift on tarmacadam, as the surface may be unstable.
Keep the lift clean for best and safest performance.
9
The maximum motorcycle weight is 450kg. DO NOT exceed this rated capacity.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
Maintain correct balance and footing, DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Before lifting check that there are no overhead obstructions.
9
When platform has been raised to the working height ensure the locking pin is engaged to prevent accidental lowering.
9
Keep children and unauthorised persons away from the work area.
9
The lowering speed will vary according to the weight of the load and the setting of the release valve.
9
DO NOT use the lift for a task it is not designed to perform.
8
DO NOT operate the lift if damaged.
8
DO NOT exceed the rated capacity of the lift.
8
DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT allow untrained persons to operate the lift.
8
DO NOT make any modifications to the lift and DO NOT adjust or tamper with the safety valve.
8
DO NOT sit or stand on the lift or hold onto it when it is being raised or lowered.
8
DO NOT attempt to raise the lift using manual strength.
8
DO NOT allow anyone to stand near the interior frame of the lift whilst raising or lowering.
8
DO NOT use the ram alone to maintain a raised motorcycle. ALWAYS insert the locking pin.
8
Before lowering the lift ensure that there are no obstructions underneath and that all persons are standing clear.
9
Before storing in safe area, ensure all parts are clean and free of grease and oil. Store lift in the lowest position.
9
WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and
‰
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
2. INTRODUCTION
Space saving design maximises garage working area. With a low minimum height of 65mm (without frame supports), it will lift and support
the bike through to a maximum height of 740mm (840mm with frame supports). Lockable in two positions for supporting the motorcycle over
extended periods. Unlike most other motorcycle lifts, it is possible to remove both wheels, front forks, steering assembly, rear swing arm and
suspension units as well as the engine. This lift also benefits from being portable and can be used anywhere with a hard level floor, making
this suitable for mobile motorcycle mechanics. Ideal for use with the Sealey range of wheel chocks to assist supporting the motorcycle, whilst
adjusting the frame supports and securing to the lift.
3. SPECIFICATION
Model No:........................................................................................MCL500
Capacity: ..............................................................................................450kg
Min./Max. Lift Height (without Frame Supports): ...........................65/740mm
Min./Max. Lift Height (with Frame Supports): ..............................165/840mm
Frame Height: ....................................................................................920mm
Maximum Frame Width: .....................................................................980mm
© Jack Sealey Limited
450KG SINGLE POST MOTORCYCLE LIFT
MODEL NO:
No reaching in
Original Language Version
MCL500
MCL500 Issue 2 (H2F) 29/04/20