Sealey VS230 Instructions

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to electrical
instructions shock
Hazard
1. Safety
1.1. electrical Safety
WarninG! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the heater is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information, it is important that the following information is read and understood.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
9
correct fuse - see fuse rating in these instructions.
do not pull or carry the appliance by the power cable.
8
do not pull the plug from the socket by the cable.
8
do not use worn or damaged cables, plugs or connectors.
8
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
9
if the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
9
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. General
do not touch heating parts with bare hands.
8
do not touch live electrical parts or electrodes with bare skin or wet clothing.
8
do not operate in the vicinity of containers under pressure, or in the presence of explosive dust, gases or
8
fumes.
do not cover or stick objects into any of the ventilation holes on the equipment.
8
WarninG! The magnetic fields created by high currents may affect the operation of pacemakers. Wearers
‰
of vital electronic equipment should consult their doctor before using induction heater.
ensure area is adequately ventilated and dry.
9
ensure ambient temperature is between -10 to 40 °c
9
Avoid using in bright sunshine or rain.
9
do not not use the machine in an environment where the air is polluted with conductive dust or gases.
8
WarninG! due to the heat generated by the induction coils blistering of painted surfaces will happen if over heated.
‰
2. introduction
mobile induction heater for fast heat delivery. Install appropriate coil and place over or around ferrous metal fixing or panel. Ideal for loosening
stubborn or seized fixings. Supplied with special dent induction block for panel expansion and induction pad for plastic trim/sticker removal.
induction element delivers high heat fast and effectively. supplied in hard-wearing carry case.
© Jack sealey limited
instructions for
induction heater 2000W
model no:
Hot surfaces do not use in
the vicinity of a
pacemaker
Original Language Version
VS230
Wear eye Wear protective
protection Gloves
Warning indoor use
magnetic field only
recommended fuse rating
13 Amp
VS230 | Issue 1 28/06/16