Technical Data; Erp Class; List Of Used Open Source Components - Bosch EasyControl CT200 Installation And Operating Instructions Manual

Technical data

Error Solution
Forgotten The serial number and access code are on the sticker,
serial number which is on the front of the quick-reference installation
and access instructions, and on the sticker at the back of the
code EasyControl and are worked into the QR code, which
can be used to enter them. If the app is used to log on,
the serial number and access code can be displayed by
navigating via the "Info menu "to the "Product
information" submenu. If the serial number and access
code cannot be found, please contact "Consumer
1)
Info". .
App has no Is the EasyControl connected to the Internet (
contact with Chapter 2)? Have the serial number and access code
EasyControl been entered? Caution, these are case sensitive.
There is possibly a slow Internet connection. Wait for a
few minutes.
The displayed The displayed temperature can be set in the app or on
temperature the EasyControl site
is too high or
too low
The touch If the touch screen does not detect anything for more
screen is not than 5 minutes, it automatically switches itself off. The
working touch screen can then only be reactivated by touching
it.
Password with EasyControl uses the standard WLAN protocol. The
$ character password for the WLAN network must therefore not
contain the $ character. Remove the $ character from
the network password.
App is not fully When the EasyControl is removed from the packaging
functioning following delivery, the latest version of the software
may not yet be installed on it. This means that possibly
not all app functions can be used. The software is
automatically updated and may take several hours, or
can be updated manually via the EasyControl app: Info
– About – Checking & Update.
Display of one of the following messages: repeated
ignition attempts, dripping/leaking DHW tap, flow rate
through the heating system too low, leak in the heating
system, filling pressure of heating system too low, or a
service display is indicated at the heat source. These
are informative signals. The heat source is working
normally.
The heat source has developed a fault. More
information is provided in the EasyControl app.
No software The software updates are performed automatically. A
updates have continuous Internet connection is required for this.
been received Updates may be missed if a timer is set on the router.
from
EasyControl
Table 2 Fault overview (the symbols are displayed on the touch screen)
8 Technical data
CT200 & CT200B
Description Unit
U V
DC
P W
max
m g (lb)
f1 (RF) f = 868.3 ...
869.5 MHz [EU]
T °C ( °F)
amb
IP-class
10
1)
.
Value
14.3 – 16.0
0.9
250 (0.551)
(P = max. 13.4 dBm)
0 ... 45 (32 ... 113)
IP30
CT200 & CT200B
Description Unit

% RH
WLAN f = 2400 MHz ...
2483.5 MHz
f2 (RF) f = 2400 MHz ...
2483.5 MHz
mm (inch)
Table 3
9

ErP Class

The data in the table below is needed to fill out the Energy related
Product (ErP) form and the ErP Data Label sticker, which are required for
systems.
Supplier is "Bosch, Bosch Group", the model is "EasyControl".
Operating functions and ErP description ErP
Room temperature-dependent, modulating V
Weather-compensated with influence of
room temperature, modulating
Room temperature control system with
several temperature sensors (zone
control), modulating
Table 4
10

List of used Open Source Components

The following text is in English for legal reasons.
The following open source software (OSS) components are included in
this product:
Name of OSS Version of OSS Name and
Component Component Version of
License
(License text
can be found in
11)
QR-Code- 1.4 MIT License
generator
http-parser 2.6.0 MIT License
MD5 2.2.1 Apache License
2.0
microJSON 1.3 BSD (Three
Clause License)
Value
10 ... 90
IEEE 802.11b (P = max. 17 dBm)
IEEE 802.11g (P = max. 14.1 dBm)
IEEE 802.15.4 (P = max. 14.6 dBm)
h = 153 (6)
w =103 (4)
d = 24 (1)
Additional
class room heating
energy
efficiency
3%
VI 4%
VIII 5%
URL of origin and
additional information
(copyright, copyleft and
modification notices; type
of link: static/dynamic,...)*
Appendix 11.3
Copyright © 2019 Project
Nayuki
Appendix 11.3
Copyright © Joyent, Inc. and
other Node contributors. All
rights reserved
Copyright © Igor Sysoev
Copyright © 2014 - 2016
Bosch Thermotechnology
Appendix 11.1
Copyright © 2006-2015,
ARM Limited, All Rights
Reserved
Appendix 11.2
Copyright © 2014 by Eric S.
Raymond
EasyControl – 6720884199 (2020/03)