Download Print this page
Sealey VS2076 Instructions

Sealey VS2076 Instructions

Diagnostic socket memory safe eobd 12v

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
Wear eye
manual
protection
1. SAFETY
1.1.
GENERAL SAFETY.
Observe standard workshop safety procedures when using the unit.
9
Ensure that the vehicle ignition switch is turned OFF before connecting the unit.
9
Ensure there is another person within hearing range, or close enough to come to your aid when working near, or with, lead-acid
9
batteries.
Wear safety eye protection and protective clothing. Avoid touching eyes while working with or near the vehicle battery.
9
Have fresh water and soap nearby in case battery acid contacts skin, clothing or eyes.
9
Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool,
9
clean running water for at least 15 minutes and seek immediate medical attention.
Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit
9
current high enough to weld a ring or the like to metal, which may cause severe burns.
Keep the work area clean and uncluttered and ensure there is adequate lighting. Keep tools and other items away from the engine
9
and ensure you can see the vehicle battery and working parts of engine clearly.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
WARNING! DO NOT use the unit where there are flammable gases or liquids.
WARNING! DO NOT use the unit on any vehicles other than those with 12Volt systems.
DO NOT use the unit if you suspect that the battery pack or the casing is damaged.
8
8
DO NOT smoke or allow a spark or flame in the vicinity of the vehicle battery or engine.
DO NOT get the unit wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT use the unit for any purpose other than that for which it is designed.
8
When not in use store the unit in a safe, dry, childproof location.
9
Ensure that the unit is fully charged before storage and recharge every 30 days.
9
1.2.
CHARGER PLUG ELECTRICAL SAFETY.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING THE CHARGER TO THE POWER SUPPLIER.
WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions: You must ensure the
risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should
be incorporated in the main distribution board. We also recommend that a RCD (Residual Current Device) is used with all electrical
products, particularly portable device which is plugged into an electrical supply not protected by an RCCB. You must also read
and understand the following instructions concerning electrical safety: The Electricity at Work Act 1989 requires all portable electrical
appliances, if used on business premises, to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once
a year.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
You must ensure that you: Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before
9
connecting to the mains power supply.
Check that the voltage marked on the charger plug is the same as the unit.
9
Uncoil the cable between the charger plug and the unit.
9
8 DO NOT pull the charger plug from the mains socket by the lead.
8 8
8 WARNING! DO NOT use any other type of charger with this product other than the supplied mains charger. Failure to observe this
8
warning could result in injury and/or fire and will invalidate the warranty.
8 DO NOT attempt to dismantle the charger plug.
8 8
8 DO NOT use the charger plug to charge or power any other electrical item.
8 8
8 8 WARNING! The unit is powered by a sealed lead-acid battery which can be dangerous if not handled with care.
8
8 Charge battery pack prior to first use. The battery will have been shipped in a low charge state.
9
8
8 8 DO NOT charge battery pack when room temperature is below 50°F (10°C) or above 104°F (40°C).
8 8
8 8 DO NOT attempt to recharge the battery pack by means of an engine generator or a DC power source.
8 8
DO NOT short-circuit the battery pack by linking both terminals with a metal object.8
8
8 8 DO NOT store the unit in locations where the temperature may exceed 104°F (40°C).
8 8
© Jack Sealey Limited
DIAGNOSTIC SOCKET MEMORY SAFE
EOBD 12V
VS2076
MODEL NO:
Wear protective
clothing
Original Language Version
8
VS2076 Issue:1 - 30/05/18

Advertisement

loading

Summary of Contents for Sealey VS2076

  • Page 1 VS2076 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Can be connected via the vehicle’s EOBD or vehicle accessory power socket. Unit features an internal 12V 7Ah sealed battery and LEDs provide battery condition and charge indicator. Supplied with mains charger. 3. SPECIFICATION Model no: ..............VS2076 Battery type: ....... Maintenance free AGM lead acid Battery capacity: ..............7Ah Cable length: ..............1.3mtr...
  • Page 3 BATTERY REMOVAL For battery removal details, see section 5.1. Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme.