Advertisement
with electric lines can lead to fire and electric shock. damaging a gas line can lead to explosion. Penetrating a water line causes
property damage and may cause electric shock.
Hold the tool only by the insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or
9
its own cord. Contact with a "live" wire will also make the exposed metal parts of the power tool "live" and shock the operator.
When working with machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more
9
securely with both hands.
Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control
9
of the power tool.
Take protective measures when dust can develop during working that is harmful to one's health, combustible or explosive.
9
Always use the auxiliary handle supplied with the machine. loss of control can cause personal injury.
9
Do Not work materials containing asbestos. Asbestos is considered carcinogenic.
8
Do Not force the drill to achieve a task it was not designed to perform.
8
Do Not operate drill where there are flammable liquids or gasses.
8
Do Not get the drill wet or use in damp or wet locations.
8
Do Not operate the drill if any parts are missing or the drill is damaged as this may cause failure and/or possible personal injury.
8
Do Not operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
Do Not carry the drill with your finger on the power switch, or carry by the power cord, or leave the drill running whilst unattended.
8
Do Not over-reach and ensure the floor is not slippery and wear non skid shoes.
8
Do Not hold unsecured work in your hand.
8
Do Not use the machine with a damaged cable. Do Not touch the damaged cable, but turn off the power supply at socket.
8
Do Not use the drill without the auxiliary handle fitted
8
When not in use, switch drill off, remove plug from power supply, clean the drill and store in safe, dry, child proof area.
9
2. INtroDuCtIoN
Powerful rotary hammer drill with patented double chuck. Chuck can be used with SdS, SdS Plus and HSS drill bits. Three drilling
functions. Variable speed control trigger. LED Mains power indicator. Supplied in storage case with 8mm,10mm and 12mm masonry
drill bits and depth gauge. Fitted with 360° auxiliary handle.
3. SPeCIfICatIoN
model No.: ........................................................ SDSPluS18
no load speed ........................................0-1700 / 0-3000 rpm
Impact rate ........................................................ 0 - 5500 bpm
Impact energy ...........................................................2 Joules
Concrete drilling diameter ........................................... 18 mm
Chuck type ........................................... double chuck system
noise power .............................................................. 99dB(A)
noise pressure .......................................................... 88dB(A)
4. oPeratIoN
warNING! disconnect from power supply before
‰
attempting any tool change, mode change, handle
repositioning, maintenance or cleaning.
4.1.
auXIlIary haNDle
4.1.1.
The auxiliary handle can be set to any position for a
secure and low-fatigue working posture.
4.1.2.
Turn the lower half of the handle counter-clockwise to
loosen it and swivel the handle around the chuck to the desired position.
To tighten, rotate the handle clockwise. Ensure a secure fitment is achieved.
4.2.
ChaNGING the tool
4.2.1.
The dust protection cap (fig.1.8) largely prevents the entry of drilling dust into
the tool holder during operation. When inserting the tool take care to avoid
damaging the cap. Immediately replace a damaged dust cap to avoid
damage to the machine.
4.2.2.
INSertING SDS-PluS DrIllING toolS
4.2.2.1.
SdS drill chucks allow for simple and convenient tool changes without the
use of additional tools.
4.2.2.2.
Clean and lightly grease the shank end of the tool. Insert the tool in a
twisting manner into the tool holder until it latches itself. Check the latching
by pulling the tool.
4.2.2.3.
To remove the tool from the chuck slide back the locking sleeve and withdraw the tool.
Note: SdS drilling tools can move freely. This can cause radial run-out at no-load. This has no effect on the accuracy of the drilled
hole as the drill bit centres itself upon drilling.
4.3.
oPeratING moDe
4.3.1.
To select the operating mode depress the release button (fig1.3) and turn the drilling/hammer selector (fig.1.2) to the required
option. An audible click will be heard when correctly latched.
4.4.
rotatIoNal SettING
4.4.1.
Rotational direction switch (fig.1.6) is used to reverse the rotational direction of the machine. This cannot be used with the On/Off
switch actuated.
4.5.
SwItChING oN/off
4.5.1.
To start the machine, push the On/Off switch (fig.1.9).
4.5.2.
To lock the On/Off switch keep it pressed and push the lock button (fig.1.4).
4.5.3.
To turn machine off, release the On/Off switch.
© Jack Sealey limited
fig.1
Original Language Version
ITeM no.
description
1
SDS-plus/SDS-max tool holder
2
Mode selector switch
3
Release button
4
lock button On/Off switch
5
Speed adjustment
6
directional control
7
locking sleeve
8
dust protection cap
9
on/Off switch
SDSPLUS18
Issue 1
24/09/19
Advertisement
