Page 1
Fujitsu Microelectronics Europe MCU-AN-390087-E-V10 Application Note F²MC-16LX FAMILY 16-BIT MICROCONTROLLER ALL SERIES FLASH PROGRAMMER YOKOGAWA AF220/221 APPLICATION NOTE...
Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in original packing and without further defects resulting from the customer´s use or the transport.
The programmer allows in-circuit programming of Fujitsu microcontrollers using the serial- synchronous interface. The Yokogawa AF220/AF221 can be adapted to different target controller types by changing the control-module (PC-card). With the FF201 module near all Fujitsu microcontrollers of the 16LX-series can be programmed. The FF205 module supports the MB91F150- family (32-Bit), the FF206 module has to be used together with MB91F360-family (32- Bit).
• Flash Programmer AF220/221 • Control Module FF201 for Fujitsu 16LX-series • Interface cable AZ210 or AZ211 or AZ212 (see chapter “Target Probe” below) Figure 1-2: Stand-alone Programmer In case that the programmer wants to be controlled by a PC then additionally the •...
FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.3 Serial Interface Cable Two serial interface cables are available. 4.3.1 AZ221 If the COM-port of the host PC uses a 9-pin D-Sub connector then interface cable AZ221 has to be used. Figure 1-5: Serial interface cable AZ221 4.3.2 AZ222...
FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.4 Target Probe The AF220/221 Flash Programmer uses a rare connector for connection to the target board: DX31A-28P/DX-28-CV from Hirose Electric (www.hirose.com) Figure 1-8: Pin Layout of Target Probe Figure 1-7: Pin Layout of Connector viewed from cable side Target Probe Connector Yokogawa offers optional three types of Probe Cables (Interface Cable).
FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.5 External Key Entry Interface Cable AZ223 Optional two buttons can be connected externally to EXT.KEY in order to start a command sequence (see chapter 9). Figure 1-12: Pin Layout of Connector EXT.KEY Pin 2...
FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.6 Pass/Error Adapter AZ266 This optional adapter uses the signal output from EXT.KEY to give the result of programming (PASS / ERROR). It can be used to drive lamps or buzzer in e.g. a manufacture line.
This chapter describes how to set up the programmer 5.1 Hardware Configuration The right PC-card (for Fujitsu 16LX-series: FF201) has to be inserted in the card slot of the programmer. Of course, the power connection with the external power-adapter and the connection to the target board via the interface cable have to be done, too.
FLASH PROGRAMMER YOKOGAWA AF220/221 Hardware Set-up 5.1.2 Connection to the Target Board All devices of the Fujitsu 16LX-series use at least eight signal lines for serial programming: • SINx, SOTx and SCKx for serial communication • MD0, MD2, P00, P01 for Mode-setting •...
FLASH PROGRAMMER YOKOGAWA AF220/221 Stand-alone operation 6 Stand-alone operation This chapter describes the Yokogawa Flash-Programmer in stand-alone mode The Yokogawa Flash-programmer can be used as stand-alone programmer. In this case, the programmer can be controlled by the integrated keypad. The basic functions are listed below.
FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller AZ290 7 Software – Remote Controller AZ290 This chapter describes how to remote control the Yokogawa Flash-Programmer by a PC The Remote Software Package AZ290 allows to set-up and to control the Flash-Programmer by a PC.
FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller AZ290 7.3 Basic Operation The basic functions for file handling (load, save, purge, etc.) on the PC-card and for programming a device are available in the tab “Basic Operations”. 7.3.1 File Operation Within the Group “File Operation”...
FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller AZ290 7.3.2 Device Function The basic functions for programming a device are available in the tab “Basic Operations”: ERASE erases the flash-memory and performs blank check BLANK checks whether the memory is cleared PROGRAM programs the flash-memory with the data of the buffer;...
FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller Library AZ291 8 Software – Remote Controller Library AZ291 This chapter lists the software library functions for programming own applications A software package AZ291 is available to program own front-end applications. The library functions are based on Visual Basic 5.0.
FLASH PROGRAMMER YOKOGAWA AF220/221 External Key Entry Interface AZ233 9 External Key Entry Interface AZ233 This chapter describes how to use two external buttons to control the Flash-Programmer In order to integrate the Yokogawa Flash-Programmer in an automatic assembly line, two external switch-buttons or relays connected to EXT.KEX can be used to start a command...
FLASH PROGRAMMER YOKOGAWA AF220/221 Pass/Error Adapter AZ266 10 Pass/Error Adapter AZ266 This chapter describes how to output the programming result For extended functionality within an assembly line, the Pass/Error adapter AZ266 (see chapter 4.6) may be helpful to output the result of programming.
FF201 Control Module for Fujitsu 16LX microcontroller FF205 Control Module for Fujitsu microcontroller 91F154, 91F155 FF206 Control Module for Fujitsu microcontroller 91F362GA (asynchronous mode) AZ221 PC cable (D-SUB 9pin – D-SUB 9pin) AZ222 PC cable (D-SUB 9pin – D-SUB 25pin)
FLASH PROGRAMMER YOKOGAWA AF220/221 Contact Addresses 12 Contact Addresses 12.1 Hitex Development Tools GmbH Mr. Roland Helbig Director Marketing & Sales Greschbachstr. 12 76229 Karlsruhe GERMANY Phone: +49-(0)721 9628 - 134 Fax: +49-(0)721 9628 - 149 E-mail: RHelbig@hitex.de http://www.hitex.de 12.2 AK Elektronik Vertriebs GmbH Mr.
Page 23
FLASH PROGRAMMER YOKOGAWA AF220/221 Appendix 13 Appendix 13.1 Time Measurement Based on a MB90F394 with 384KByte Flash the following execution time was measured: Command Time Remark ERASE 9 sec called by One Action key (CSB-file) BLANK CHECK 4 sec called by One Action key (CSB-file) ERASE (incl.