Related Manuals for Sony BKSM-R103
Summary of Contents for Sony BKSM-R103
- Page 1 ANALOG OUTPUT BOARD BKSM-R103 INSTALLATION MANUAL 1st Edition Serial No. 10001 and Higher...
- Page 2 ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
-
Page 3: Table Of Contents
..................... 1-1 (E) 2. Installation 2-1. Installation of Board and Rear Panel ............ 2-1 (E) 2-2. Matching Connectors and Cables ............2-5 (E) 2-3. Input and Output Signal of Connector ..........2-5 (E) 2-4. Internal Switch ..................2-6 (E) 1 (E) BKSM-R103... -
Page 5: Manual Structure
Manual Structure Purpose of this manual This manual is the installation manual of the BKSM-R103 Analog Output Board. This manual is intended for use by trained system and service engineers, and describes the information regarding installation. Contents The following is a summary of all the section for understanding the contents of this manual. -
Page 7: Overview
Section 1 Overview The BKSM-R103 is the board which converts the output data from the decoder board of the DSM-R1/D1 into analog composite video signal and analog audio signal, and outputs these converted signals. In the BKSM-R103, the video data from the decoder board of the DSM-R1/D1 is decoded and converted digital to analog, then output this converted signal as analog composite video signal. -
Page 9: Installation
ANALOG OUT rear panel to the “1” side. Similarly, when the APR-31 board is installed in “2” side, install the ANALOG OUT rear panel to the “2” side. DSM-R1/D1 DSM-R1/D1 APR-31 board OUT 2 side OUT 1 side OUT 2 side OUT 1 side 2-1 (E) BKSM-R103... - Page 10 (2) Secure the ANALOG OUT rear panel using the four screws (B 3x6) supplied with the BKSM-R103. The BKSM-R103 comes with the two varieties of the ANALOG OUT rear panel assembly. Use either of the (3) Secure the APR-31 board using the four screws (PWH two panels for your purpose.
- Page 11 CP-309 board CN1 (white) APR-31 board APR-31 board BNC connector CP-309 board CN1 (white) BNC connector Harness clamper 1 : When the board is installed in “1” side 2 : When the board is installed in “2” side 2-3 (E) BKSM-R103...
- Page 12 1 : When the board is installed in “1” side 2 : When the board is installed in “2” side There is no necessity to perform the check/adjustment after the APR-31 board and the ANALOG OUT rear panel installing. 2-4 (E) BKSM-R103...
-
Page 13: Matching Connectors And Cables
*2 : ITT CANNON XLR-3-12C or the equivalent When XLR 5-pin connector is connected to the analog audio input (XLR 3-pin, female) of the VTR, use the following cable. . Cable : SONY CCXA-53 or the equivalent CCXA-53 DSM-R1/D1 3P (M) -
Page 14: Internal Switch
The address on the board is shown by ( ) mark. S300 (G-9) : Factory use Factory setting : All switch levers are set to OFF. Be sure to use this switch with factory setting. indicates the switch lever position.) 2-6 (E) BKSM-R103... - Page 15 The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any...
- Page 16 Printed in Japan Sony Corporation BKSM-R103 (SY) J, E 1998. 2 16 Broadcasting & Professional Systems Company 3-200-069-01 ©1998 Published by Global Support Promotion Dept.