Sealey SGS115 Instructions

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. sAfeTy
1.1. electrical safety
wArning! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance test)
tested.
electrical safety information, it is important that the following information is read and understood.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
9
fuse rating in these instructions.
dO nOT pull or carry the appliance by the power cable.
8
dO nOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
dO nOT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
class ii products are wired with live (brown) and neutral (blue) only are marked with the class ii symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
c) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
dO nOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. General safety
disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.
9
maintain grinder and discs in good condition. check moving parts and alignment. if necessary use an authorised service agent.
9
replace or repair damaged parts. use recommended parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the grinder clean for best and safest performance.
9
wArning! Always work with the grinder safety guard in place.
‰
Wear approved safety goggles, ear defenders, appropriate dust mask if grinder generates dust and safety gloves.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain long hair.
9
use grinder in a suitable work area. Keep area clean, tidy and free from unrelated materials and ensure that there is adequate lighting.
9
maintain correct balance and footing. do not over-reach and ensure that the floor is not slippery. Wear non-slip shoes.
9
use only approved grinding discs and only use the normal grinding surface. never use the side or upper surface of disc for cutting.
9
the grinding disc may only be changed by a person holding a grinding wheel certificate.
9
check grinding disc to ensure it is not split, cracked or damaged in anyway. if in doubt do not use the disc.
9
Grinding discs must be securely attached before use, but not overtightened.
9
secure unstable work piece with a clamp, vice or other adequate holding device and ensure that the grinder is gripped with both hands.
9
Keep children and unauthorised persons away from the work area.
9
dO nOT operate the grinder if any parts are missing or damaged.
8
dO nOT use the grinder for a task it is not designed to perform.
8
wArning! dO nOT grind or sand materials containing asbestos.
‰
© Jack sealey limited
instructions for
Angle grinder slim Ø115mm 750w/230v
model no:
Wear protective Wear safety
gloves footwear
Original Language Version
sgs115
Wear protective Wear ear
clothing protection
recommended fuse rating
5 Amp
sGS115 | Issue 1 28/10/16