Sealey SR2000 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear protective
instruction gloves
manual
1. sAFetY
electrical safety
1.1.
wArning! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply
leads, plugs and all electrical connections for wear and damage. sealey recommend that an rcd
(residual current device) is used with all electrical products. You may obtain an rcd by contacting your
local sealey dealer. if the kit is used in the course of business duties, it must be maintained in a safe
condition and routinely PAt (Portable Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
9
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
9
correct fuse - see fuse rating in these instructions.
dO nOt pull or carry the appliance by the power cable.
8
dO nOt pull the plug from the socket by the cable.
8
dO nOt use worn or damaged cables, plugs or connectors.
8
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
9
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
9
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
9
only use one single extension cable at a one time. dO nOt daisy chain extension cables. unwind the
9
extension cable fully.
1.2. General
dO nOt touch heating parts with bare hands.
8
dO nOt touch live electrical parts or electrodes with bare skin or wet clothing.
8
dO nOt operate in the vicinity of containers under pressure, or in the presence of explosive dust, gases or fumes.
8
dO nOt cover or stick objects into any of the ventilation holes on the equipment.
8
wArning! The magnetic fields created by high currents may affect the operation of pacemakers. Wearers
‰
of vital electronic equipment or those who have metallic surgical implant should consult their doctor before using equipment.
dO nOt wear clothing with metallic components e.g. belt buckles, buttons, zips when working with the equipment as it can
8
cause such items to heat up.
remove any metallic components e.g. keys, chains, tools etc. while you operate the equipment and dO nOt wear any metallic
9
objects such as jewellery, watches, piercings etc. on your body.
dO nOt use the equipment in the rain or in humid conditions or immerse it in water.
8
dO nOt leave the equipment unattended whilst turned on.
8
dO nOt attempt to repair or service the equipment.
8
ensure area is adequately ventilated and dry.
9
ensure ambient temperature is between -10 to 40 °c
9
Avoid using in bright sunshine or rain.
9
dO nOt use the equipment in an environment where the air is polluted with conductive dust or gases.
8
wArning! Fumes and smoke from hot/burning paints, adhesives etc. are toxic. Wear a suitable mask in such circumstances.
‰
2. intrOductiOn
Supply: 230V-13A (13A Plug fitted). Professional quality stud welder for fast, efficient body repairs. Removes dents quickly, without
holes or the need to remove interior trim. no burn through means that removal of studs and washers is easy and preparation work
before repainting is minimised. suitable for use on steel or aluminium and can weld studs, washers and tabs. Patented quick puller
attachment allows removal of smaller dents without the need for studs or washers. supplied in heavy-duty storage case.
© Jack sealey limited
instructions for
stud welding kit 230v
model no:
Wear eye Wear face
protection mask
Original Language Version
sr2000
Wear ear Wear protective Wear welding
protection clothing
do not use in indoor use only
mask
the vicinity of a
pacemaker
recommended fuse rating
13 Amp
sR2000 Issue 1 15/06/18