You should wipe out the dryer drum with a damp doth before using to remove dust from storing or shipping. Thank you for buying a Whirlpool appliance. Please complete and mail the Owner Flegistration Card provided with this product. Then complete the form bebw.
Important Safety htructions To reduce the rlsJc of fire, elsctrlcal shock, or Injury to persons when uslng your dryer, follow bask prscautlons, @ Read all Instructions before using the dryer. NEVER dry items cleaned, washed, soaked in or spotted with wax, paint, gasoline or flammable fluids in the dryer.
Operating Instructions Starting your dryer the chart below and sure to refer to and control setting information before starting your dryer. NOTE: Do not overdry. Overdrying can cause shrinkage, static ding, and damage some fabrics. TYPE Of LOAD Cottone and Ilneno EXTRA HEAVY-Bedspreads, mattrass pads, quilts HEAVYWEIGHT-To%&.
Page 5
1. Select a cycle by turning the Cycle Control Knob either way. Stop when the indicator on the knob’s outer ring points to the cycle and time you want. See pages 6-6 for further cycle information. 2. Push the Start Button to start the dryer.
Operating lnstructlona Contlnued The REGULAR/PERMANENT PRESS cycle The REGULAR/PERMANENT PRESS cyde helps provide the special care that cottons, permanent press and synthetic fabrics need. The cycle consists of a timed period of heated drying and a 10 minute cooldown period. During the cool down, the bad tumbles without heat This helps keep wrinkles from setting and makes the...
The FLUFF AIR cycle Fire Hazard Do not dry ptsatlc or rubber ltema with heat. Urn FLUFF AIR cycle, or line dry. Failure to do so could result in fin or damaged Yema The dryer does not heat when the Cycle Control Knob is set in FLUFF AIR.
Operating lnstructlona Contlnued Additional Dryer Feature Using DAMP DRY Use this setting to dry damp items that do not require an entire drying cycle, or to dry items to damp level. (Two examples are heavy cottons, such as jeans, which you do not want to become stiff, or cotton clothes which are easier to press when damp.) 1.
Caring For Your Dryer Product and Fabrk Damage Hazard Do not run the dryer wfth the lint ween damaged, blocked or mlsslng. Doing so can cause overheatlng and damage to both the dryer and fabrks. foose, Cleaning the lint screen The lint screen is located under a lid on top of the dryer.
Carlng For Your Dryer Contlnued Cleaning the dryer ElectrIcal Shock and Personal InJury Hazard Turn off the elecfrlcal power before cbanlng the Interbr. Make sure the dryer ls cool. Failure to do so could result In electrIcal shhock or Injury. Fire Hazard Use non-flammable cleaner.
l-lea1 domalI tennlnslr Eleotrlc dryer with bade panel ramovad Gar dryer with kwer front- acoem panel removed Lint removal Lint can gather inside the dryer and be a fuel for fire. ft is recommended the lint be removed every 2 to 3 years, or more often, depending on dryer usage.
Page 12
Removesorewo A before opedng Drum se111 Bid0 panel wire cllp- hold. door lfyourdrywbgasandhusafuUfront pw~rsmovefKlntpenelasklbure: 1. Unplug the power supply cord or turn off the electrical power. 2. Open lint screen lb. Remove two screws in lint screen area. 3. Open top by pulling forward and up at each front corner (see view A).
United States. To locate the authorized Whirlpool service company in your area. call our Consumer Assistance Center telephone number (see Step 2) or bok in your telephone directory Yelbw Pages...
Page 14
Whirfpool Corporation for qualify parts. Look for this symbol of qualify whenever you need a replacement part for your Whirlpool appliance. FSP replacement parts will fii right and work right, because they are made to the same exacting specifications used to build every new Whirlpool appliance.
After checking “Service and Assistance,’ additional help can be found by calling our Consumer Assistance Center telephone number, 14004534301, anywhere in the U.S. Q Registered Trademark / SM Service Mark of Whirlpool Corporation Part No. 3395437 01992 Whirlpool Corporation DROO from Printed in U.S.A.