Sealey E540.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction Wear eye
manual protection
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2 GENERAL SAFETY
Only power the tool from the mains supply.

Disconnect the tool from the mains supply before changing accessories, servicing or performing any maintenance.

Maintain tool and accessories in good condition. Check moving parts and alignment. If necessary use an authorised service agent.

Replace or repair damaged parts using recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.

Wear approved safety eye protection with side shields and a dust mask if generating dust.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.

Use the tool in a suitable working area, keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.

Prevent body contact with earthed surfaces to avoid electric shock e.g. pipes, radiators, refrigerators etc.

Maintain correct balance and footing.

Keep children and unauthorised persons away from the working area.

Secure unstable workpiece with a clamp, vice or other adequate holding device.

Avoid unintentional starting. Keep the tool clean for best and safest performance.

When not in use switch tool off and unplug it from the mains supply. Store it in the case and put in a dry, childproof area.

DO NOT operate the tool if any parts are missing or damaged as this may cause failure and/or personal injury.

DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.

DO NOT over-reach. Ensure the floor is not slippery and wear non-slip footwear.

DO NOT use the tool for a task it is not designed to perform.

DO NOT carry the tool by the cable.

© Jack Sealey Limited
MULTI-PURPOSE ROTARY TOOL & ENGRAVER
KIT
E540.V3
MODEL No:
Wear a mask
Original Language Version
Recommended fuse
rating:3A
E540.V3 Issue: 3(4) - 03/09/18