Table of Contents
Advertisement
Quick Links
Rear Quick-Attach System
2013 and After Groundsmaster
Model No. 30810—Serial No. 315000001 and Up
Model No. 30812—Serial No. 315000001 and Up
Note: The machine must be equipped with the Auxiliary Power Unit Kit, Toro part no. 30382.
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Cylinder-support assembly
Bolt (3/8 x 2-3/4 inches)
Bolt (3/8 x 1-1/4 inches)
Bolt (3/8 x 1 inch)
Nut (3/8 inch)
Lift-arm assembly
Bolt (7/8 x 4-1/2 inches)
Jam nut (7/8 inch)
Spindle washer
Bolt (1/2 x 1-1/2 inches)
Locknut (1/2 inch)
Cylinder-mount pivot pin
Grease fitting
Link mount
Bolt (3/8 x 1 inch)
Nut (3/8 inch)
Lift-arm assembly
Bolt (7/8 x 4-1/2 inches)
Jam nut (7/8 inch)
Spindle washer
Bolt (1/2 x 1-1/2 inches)
Locknut (1/2 inch)
Pivot pin
Grease fitting
Register at www.Toro.com.
®
7200 Series Mower
WARNING
CALIFORNIA
Qty.
–
1
2
3
1
3
1
2
2
8
1
1
1
1
1
3
3
1
2
2
8
1
1
1
1
Form No. 3395-750 Rev B
Installation Instructions
Use
Prepare the machine.
Install the lift-arm assembly (for Model
30810 only).
Install the lift-arm assembly(for Model
30812 only).
Original Instructions (EN)
All Rights Reserved *3395-750* B
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro 30810
Summary of Contents for Toro 30810
- Page 1 7200 Series Mower Model No. 30810—Serial No. 315000001 and Up Model No. 30812—Serial No. 315000001 and Up Installation Instructions Note: The machine must be equipped with the Auxiliary Power Unit Kit, Toro part no. 30382. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
-
Page 2: Table Of Contents
Cable tie Relay bracket Relay Bolt (1/4 x 1/2 inch) Install the relays and switches (for Nut (1/4 inch) Model 30810 only). Bolt (1/4 x 3/4 inch) Decal (from Auxiliary Power Unit Kit) Switch Relay bracket Relay Bolt (1/4 x 1/2 inch) - Page 3 Installing the Lift-Arm Assembly Model 30810 Parts needed for this procedure: Cylinder-support assembly Bolt (3/8 x 2-3/4 inches) Bolt (3/8 x 1-1/4 inches) Bolt (3/8 x 1 inch) Figure 1 Nut (3/8 inch) 1. Bolt 2. Nut Lift-arm assembly Bolt (7/8 x 4-1/2 inches) 2.
- Page 4 3. Mount the lift-arm assembly to the rear frame 6. Secure the threaded link rod end to the cylinder-support members, with 2 bolts (7/8 x 4-1/2 inch), 2 jam nuts assembly with a bolt (1/2 x 1-1/2 inch) and locknut (7/8 inch), and as many spindle washers as necessary (1/2 inch) as shown in Figure...
- Page 5 Installing the Lift-Arm Assembly Model 30812 Parts needed for this procedure: Link mount Bolt (3/8 x 1 inch) Nut (3/8 inch) Lift-arm assembly Bolt (7/8 x 4-1/2 inches) Figure 7 Jam nut (7/8 inch) 1. Link mount Spindle washer Bolt (1/2 x 1-1/2 inches) 2.
- Page 6 4. Adjust the length of the threaded link to 19 cm (7-1/2 7. Thread a grease fitting into the end of the pivot pin inches) and tighten the jam nuts (Figure (Figure 11). Note: Position the grease fitting as shown in Figure Figure 9 1.
-
Page 7: Tee Fitting (Model 30812 Only)
Model 30812 1. Radiator frame 2. Oil-cooler-return hose 2. Route the short hose from the manifold to the oil-cooler-return hose location. 3. For model 30810 only: install the short hose to the oil-cooler hose as follows:... - Page 8 5. On the right frame, locate the deck-lift-valve assembly (Figure 18). Figure 18 1. Plug 2. Valve assembly 6. Remove the plug from the left side of the valve assembly (Figure 18). 7. Thread the hydraulic valve fitting into the opening of Figure 17 the valve (Figure...
-
Page 9: Relay Bracket
20). Note: The long hose will follow another hose from Installing the Relays and the transmission bay to the valve assembly. Switches Model 30810 Parts needed for this procedure: Relay bracket Relay Bolt (1/4 x 1/2 inch) Nut (1/4 inch) -
Page 10: Decal (From Auxiliary Power Unit Kit)
4. Unlatch the control-panel cover and move it aside (Figure 22). Figure 24 1. Decal 3. Lift/lower switch (3-position switch) 2. Float/power-down switch (2-position switch) Figure 22 9. Insert the switches into the appropriate mounting holes 1. Control panel 2. Latch (Figure 24). -
Page 11: Switch
3. Remove the bracket, and drill a hole (0.281 inch) through both walls of the frame in the location that you marked. 4. Install the bracket with the hardware you used to Installing the Relays and loosely install the bracket and secure the bracket to the new hole with a bolt (1/4 x 2-1/2 inches) and nut (1/4 Switches inch). -
Page 12: Switch
Wiring harness Procedure Note: The machine must be equipped with the Auxiliary Power Unit Kit, Toro part no. 30382. 1. Cover exposed connectors on the wiring harness with masking tape or electrical tape to keep debris out of the connectors while routing the harness. - Page 13 Figure 30 Figure 31 1. Blower PTO switch (used with blower) 6. Deck lift out (A and B) 2. Lift/lower switch 7. Main wiring harness 3. Ground 8. Relays (6) 4. Power 9. Hydraulic manifold 5. Deck lift in (A and B) 10.
- Page 14 OWER the machine to increase ground engagement force (Figure 33). Higher ground engagement force decreases the traction capacity of the machine. Figure 34 1. Threaded link Figure 32 Model 30810 1. F 2. L switch LOAT POWER DOWN LOWER switch...
- Page 15 Weight Part Number Weight Description Qty. Models 30695 with 30354, 30481, or 30353 and Weight Required 125-2655-03, Front frame weights, Rear QAS (Model 30810) and no attachment 146 lb 125-2670, Weight bracket, and 114-4096 and Suitcase weights 125-2655-03, Front frame weights,...
- Page 16 60 or 62 inch width of cut Additional Front Weight Part Number Weight Description Qty. Models 30695 with 30456 or 30457 and Weight Required Rear QAS (Model 30810) and no attachment 146 lb 125-2655-03, Front frame weights, 125-2670, Weight bracket, and 114-4096...
- Page 17 Debris Blower (Model 30393) 318 lb 125-2655-03, Front frame weights, 125-2670, Weight bracket, and 114-4096 and Suitcase weights Not Approved Rahn Groomer (Allied Product) Weight Charts for Model 30812 Use the following weight charts to determine the correct amount of front weight required for your machine. 72 inch width of cut Additional Front Weight Part Number...
- Page 18 62 inch width of cut Additional Front Weight Part Number Weight Description Qty. Models 30495, or 30487 with 30456 or 30457 Weight Required With no hard canopy, model 30349 and 67 lb 125-2670 Front weight bracket Rear QAS (Model 30812) and no attachment 114-4096 42 lb front weight Finish Grader (Box Rake) (Model 08754)
- Page 19 Operating Tips • Read and understand the attachment Operator's Manual before using the machine. • Make sure that the appropriate weight mount bracket and front weight(s) are installed for the rear attachment. • Remove rear attachment and any loose front-end weights prior to mowing.
- Page 20 Notes:...
- Page 21 Notes:...
- Page 22 Notes:...
- Page 23 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 24 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.