Advertisement
2. INTRODUCTION
Powerful demolition hammer with 1" SDS-Hex chuck. Vibration reducing rubber grips. Heavy-duty metal body construction. Anti-fatigue trigger
lock. 360° Auxiliary handle. Supplied in metal storage case with 30mm flat chisel.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . DHB1600
Chuck Type: . . . . . . . . . . . . . . . . . . . . . . . 1" SDS-Hex
Electrical Class: . . . . . . . . . . . . . . . . . . . . . . . .Class II
Electrical Plug Type: . . . . . . . . . . . . . . . . . . .3-Pin BS
Impact Energy: . . . . . . . . . . . . . . . . . . . . . . . . . . . 45J
Impact Rate: . . . . . . . . . . . . . . . . . . . . . . . . 2000bpm
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . .18.65m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5m/s²
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . 104dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . 99dB(A)
4. OPERATION
WARNING! Disconnect hammer from the mains
‰
power before changing accessories, servicing or
performing any maintenance.
IMPORTANT: This machine is designed for
heavy duty demolition and chiseling work
using the appropriate chisel.
▲
DANGER! Check the drilling point for concealed
electrical cables, gas and water pipes using a
cable/pipe detector.
4.1.
ADJUSTABLE HANDLE
4.1.1.
To position the adjustable handle (fig.1.3),
unscrew the adjusting knob (fig.1.8) and rotate
the handle to the preferred position, tighten the
knob fully.
IMPORTANT: This tool must always be used
with the adjustable handle secured in place
and held with both hands.
▲
DANGER: The machine must only be held
using the two handles. Otherwise the user
may suffer an electric shock if they chisel into
cables.
4.2.
INSERTING THE TOOL
4.2.1.
Clean the chisel before fitting it, apply a thin
coating of grease to the tool shaft.
4.2.2.
Pull out the locking bolt (fig.1.4) as far as
possible, turn it through 180° and release it
(fig.2).
4.2.3.
Insert the tool into the tool mounting (fig.2) and
push it in as far as possible (fig.3).
4.2.4.
Pull out the locking bolt (fig.1.4) again, turn it
through 180° in the opposite direction and
release it (fig.3).
4.2.5.
Check the lock by pulling the tool.
4.3.
REMOVING THE TOOL
4.3.1.
To remove the tool, reverse process 4.2.
4.4.
SWITCHING ON AND OFF
4.4.1.
To switch ON: press the trigger switch and
hold on (fig.4.2). To switch OFF: release the
trigger switch (fig.4.2).
4.4.2.
Press the trigger switch and engage the lock
for continual use. Press the trigger switch
again to release the trigger lock.
NOTE: You will only achieve good results if
you use sharp chisels. You should therefore
sharpen the chisels promptly to ensure that
they produce good results and provide a long
service life.
IMPORTANT: You only require slight contact pressure for chiseling. Excessive contact pressure will place an unnecessary strain
on the motor. Check the chisels at regular intervals. Sharpen or replace blunt chisels.
WARNING! The vibration value changes according to the area of application of the electric tool and may exceed the specified
value in exceptional circumstances.
© Jack Sealey Limited
5
4
CONTENTS
Item
Description
1
Handle
2
ON/OFF Trigger Switch with Lock
3
Additional Handle
4
Locking Bolt
5
Tool Chuck
6
Inspection Window/Oil Filler
7
Wrench
8
Auxiliary Handle Knob
6
Original Language Version
8
6
fig.2
fig.3
fig.4
fig.4
fig.5
fig.6
DHB1600 Issue 2 (2,3) 10/02/2020
2
fig.1
1
3
7
2
7
6
Advertisement
