Configuring The System Settings - Yamaha RX-V377 Series Service Manual

RX-V377/HTR-3067

■ CONFIGURING THE SYSTEM SETTINGS

Configure the system settings of the unit while viewing the front display.
1
Set the unit to standby mode.
2
While holding down STRAIGHT on the front panel, press z (power).
z (power)
PROGRAM STRAIGHT
3
Press PROGRAM to select an item.
4
Press STRAIGHT to select a setting.
5
Press z (power) to set the unit to standby mode and turn it on again.
The new settings take effect.
ADVANCED SETUP menu items
• Default settings are underlined.
Item Function
(U.S.A. and Canada models only)
SP IMP.
Changes the speaker impedance setting.
R E M O T E D I S e e l c s t h t e u i n s ' t e r m o e t c o t n o r I l . D
(Asia, Taiwan and General models only)
TU
Changes the FM/AM tuning frequency setting.
T V F O R M A T S i w c t h e s h t e v d i e o s g i n l a y t p e f o H D M I o u p t
N I T I R e s o t e r s h t e d e a f u t l s e t t n i g . s
U P D A T E U p d a e t s h t e r i f m w r a . e
VERSION Checks the version of firmware currently installed on the unit
Changing the speaker impedance setting (SP IMP.)
(U.S.A. and Canada models only)
CHARGE ENHANCER STEREO TUNED SLEEP MUTE
OUT VOL.
ECO
SP IMP.••8¬MIN
ADAPTIVE DRC VIRTUAL
Change the unit's speaker impedance settings depending on the impedance of the
speakers connected.
Settings
Select this option when you connect 6-ohm speakers to the unit. You
6 Ω MIN
can also use 4-ohm speakers as the front speakers.
Select this option when you connect 8-ohm or higher speakers to the
8 Ω MIN
unit.
112
Selecting the remote control ID (REMOTE ID)
CHARGE
OUT
ECO
REMOTE ID••ID1
Change the unit's remote control ID so that it matches the remote control's ID (default:
ID1). When using multiple Yamaha AV receivers, you can set each remote control with a
unique remote control ID for its corresponding receiver.
Settings
ID1, ID2
Changing the remote control ID of the remote control
1
To select ID1, hold down the cursor key (e) and SCENE (BD/DVD) together for 3
seconds.
To select ID2, hold down the cursor key (e) and SCENE (TV) together for 3
seconds.
Changing the FM/AM tuning frequency setting (TU)
(Asia, Taiwan and General models only)
CHARGE
OUT
ECO
TU••••FM50/AM9
Change the FM/AM tuning frequency setting of the unit depending on your listening
environment.
Settings
FM100/AM10
FM50/AM9
u . t
Switching the video signal type (TV FORMAT)
CHARGE
OUT
ECO
TV FORMAT•NTSC
Switch the video signal type of HDMI output so that it matches to the format of your TV.
Since the unit automatically selects the video signal type so that it matches to the TV, it
is unnecessary to change the setting normally. Change the setting only when images
on the TV screen do not appear correctly.
Settings
NTSC, PAL
Default
U.S.A., Canada, Korea, Taiwan and General models: NTSC
Other models: PAL
ENHANCER STEREO TUNED SLEEP MUTE
VOL.
ADAPTIVE DRC VIRTUAL
ENHANCER STEREO TUNED SLEEP MUTE
VOL.
ADAPTIVE DRC VIRTUAL
Select this when you want to adjust the FM frequency by 100-kHz
steps and AM by 10-kHz steps.
Select this when you want to adjust the FM frequency by 50-kHz steps
and AM by 9-kHz steps.
ENHANCER STEREO TUNED SLEEP MUTE
VOL.
ADAPTIVE DRC VIRTUAL
Restoring the default settings (INIT)
CHARGE ENHANCER STEREO TUNED SLEEP MUTE
OUT VOL.
ECO
INIT••••CANCEL
ADAPTIVE DRC VIRTUAL
Restores the default settings for the unit.
Choices
ALL Restores the default settings for the unit.
CANCEL Does not perform an initialization.
Updating the rmware (UPDATE)
CHARGE ENHANCER STEREO TUNED SLEEP MUTE
OUT VOL.
ECO
UPDATE•••••USB
ADAPTIVE DRC VIRTUAL
New firmware that provides additional features or product improvements will be
released as needed. Updates can be downloaded from our website. For details, refer
to the information supplied with updates.
Firmware update procedure
Do not perform this procedure unless firmware update is necessary. Also, make sure
you read the information supplied with updates before updating the firmware.
1
Save the downloaded firmware to the root folder of a USB memory device.
2
Press PROGRAM on the front panel to select "UPDATE".
3
Connect the USB memory device to the USB jack.
4
To start firmware update, press INFO on the front panel.
Checking the rmware version (VERSION)
CHARGE ENHANCER STEREO TUNED SLEEP MUTE
OUT VOL.
ECO
VERSION••xx.xx
ADAPTIVE DRC VIRTUAL
Check the version of firmware currently installed on the unit.