Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice
!
regulations are adhered to when using this workstation.
Locate workstation in a suitable working area.
"
Keep the work area clean, uncluttered and ensure there is adequate lighting.
"
WARNING! Use workstation on level and solid ground, preferably concrete. Avoid
!
tarmacadam since the workstation may sink into the surface.
Keep the workstation clean and tidy in accordance with good workshop practice.
"
Keep children and unauthorised persons away from the working area.
"
DO NOT use the workstation for any purpose other than that for which it is designed.
#
DO NOT exceed maximum capacity of workstation.
#
DO NOT undertake work on the workstation without the workpiece being adequately secured.
#
Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey dealer.
DO NOT use the workstation out of doors.
#
DO NOT get the workstation wet or use in damp or wet locations or areas where there is
#
condensation.
DO NOT clean the workstation with any solvents which may damage the paint surface or the
#
protective coating on the wooden top.
DO NOT pull out all drawers at the same time.
#
Maximum weight for each drawer is 25 kg, full load for workstation is 250kg.
!
2.
CONTENTS AND SPECIFICATION
2.1
Powder coated steel panels with 25mm wood laminate top. Five drawers. Supplied flat packed.
2.2
Table Size (W x D): 838 x 508mm
Working Height: 865mm
Capacity: 250kg
2.3
Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make
immediate contact with your Sealey dealer.
A . . . .SIDE PANEL
C . . . .BOTTOM RAIL
D . . . .TOP RAIL
G . . . .LEFT SIDE PANEL
H . . . .RIGHT SIDE PANEL
J . . . . .BACK PANEL
M . . . .DRAWER
O . . . .CORNER BRACE
INSTRUCTIONS FOR:
HEAVY-DUTY WORKSTATION WITH 5 DRAWERS,
BALL BEARING RUNNERS
AP2050BB
:
MODEL
P . . . . .WOODEN TOP
Q. . . . .LEFT SIDE RUNNER U . . . . .HEX HEAD SCREW 5/8"
R . . . . .RIGHTSlDE RUNNER
S . . . . .SCREW (M5x12)
T . . . . .ADJUSTABLE LEG LEVELLER
. . . . . .
AP2050BB - 1 - 260407
Advertisement
Related Manuals for Sealey Power Products AP2050BB
Summary of Contents for Sealey Power Products AP2050BB
- Page 1 AP2050BB MODEL Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 ASSEMBLY Step 1. As shown in the diagram attach the two large side panels (A) to the bottom rails (C). Ball bearing runner disassembly: Press the plastic lock spring up or down, and pull the inner slide out. To put the runners back on, slot the inner slide into the middle slide and push all the way in.
- Page 3 Step 3. Attach panels (G, H) to the main unit by screwing onto side panels (A). Screw the top rails (D) onto the front and back. STEP 5. Secure the back panel (J) using 4 screws, 1 in each STEP 4. corner.
- Page 4 STEP 6. Turn the workbench upside down and screw in the corner braces (O) as shown in the diagram. At each corner attach the leg levellers (T). Slide the workbench top (P) under the main unit and fix with 4 hex head screws (U). STEP 8.