Table of contents Before Using the Product Connecting and Using a Source Device Screen Setup Safety Precautions Read below before connecting the product. Picture Mode Electricity and Safety Ports Brightness Installation Operation Connecting and Using a PC Contrast Connection Using the HDMI Cable Cleaning Sharpness Connection Using an HDMI-DVI Cable...
Page 3
System Requirements Power LED On Driver Installation Adjusting OSD (On Screen Display) settings Troubleshooting Guide Transparency Position Requirements Before Contacting Samsung H-Position Customer Service Centre V-Position Product diagnosis (Screen issue) Checking the Resolution and Frequency Language Check the following. Display Time...
Page 4
Table of contents Specifications General Standard Signal Mode Table Appendix Responsibility for the Pay Service (Cost to Customers) Not a product defect A Product damage caused by customer's fault Others Extended warranty...
DC voltage: Rated voltage marked • Only use the power cord provided with your product by Samsung. Do not use the power cord with literature concerning operation and with this symbol is DC voltage. other products.
Do not expose the product to direct sunlight, heat, or a hot object such as a stove. ‒ Be sure to consult Samsung Customer Service Centre if you want to install the product at such a ‒ The product lifespan may be reduced or a fire may result.
‒ Be sure to power off the product and disconnect the power cord when water or other foreign Warning substances have entered the product. Then contact Samsung Customer Service Centre. • There is a high voltage inside the product. Never disassemble, repair or modify the product •...
― Contact your nearest Samsung Customer Service Centre if you want to clean the inside of the product • Disconnect the power cord from the power socket if you do not plan on using the product for an (Service fee will be charged.)
Correct posture to use the product Use the product in the correct posture as follows: • Straighten your back. • Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at the screen. •...
Chapter 02 Preparations Installation Attaching the Stand Insert the stand neck into the stand base in the Place the protective Styrofoam (cushion) included in direction shown in the figure. Tightly fasten the the package on the floor and place the product facing connecting screw at the bottom of the stand base.
Removing the Stand Precautions for moving the product ― Before removing the stand from the product, place the product on a flat and stable surface with the screen facing down. • Do not press down on the product. There is a •...
Checking the space around the product Adjusting the Product Tilt and Height ― The colour and shape of parts may differ from what is shown. Specifications are subject to change without Make sure to have enough space for ventilation when placing the product. An internal temperature rise notice to improve quality.
Rotating the Product Anti-theft Lock ― The colour and shape of parts may differ from what is shown. Specifications are subject to change without ― An anti-theft lock allows you to use the product securely even in public places. notice to improve quality. ―...
‒ Samsung shall not be held liable for any product damage or personal injury caused by using a wall-mount kit other than the one specified or from an attempt to install the wall-mount kit on your own.
Control Panel Parts Description JOG Button Multi directional button that helps navigate. This LED is power status indicator. ― The colour and shape of parts may differ from what is shown. Specifications are subject to change without ― You can select the power LED operation to be enabled or disabled on Power LED notice to improve quality.
Direct Key Guide ― On the Direct Key Guide screen, the following menu options appear when the product screen is switched on or the input source is changed. ― The Direct Key Guide screen shows if Eye Saver Mode is enabled. ( : On, : Off) Eye Saver Mode...
Chapter 03 Connecting and Using a Source Device Read below before connecting the product. Ports ― The functions available may vary depending on the product model. The colour and shape of parts may Before connecting the product, check the shapes of both ports of the supplied signal cables and differ from what is shown.
Connecting to headphones or earphones ― When connecting an HDMI cable, use the cable that came with the components of the product. If you use an HDMI cable other than provided by Samsung, the image quality may be degraded. Connection Using an HDMI-DVI Cable ―...
Connecting the Product to a PC as a USB HUB Using the product as a hub, connect and use various source devices with the product at a time. ― To detect and start a USB device faster, connect the device to the USB port on the product.
Tidying Up the Connected Cables Tilt the display, as shown in the figure. Rotate the product to the highest vertical Connect the corresponding cables. Arrange the cables through the groove on the position. back of the product, and then attach the COVER- REAR SUB ( ).
Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language on information message and change the resolution on your PC to the optimum setting.
Chapter 04 Screen Setup Function Key Guide → → Picture ― The functions available may vary depending on the product model. The colour and shape of parts may mode differ from what is shown. Specifications are subject to change without notice to improve quality. •...
Brightness Color You can adjust the general brightness of the picture. (Range: 0~100) Adjust the tint of the screen. ― This menu is not available when A higher value will make the picture appear brighter. Picture Mode is set to Cinema Dynamic Contrast mode.
Black Level Response Time If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/ Accelerate the panel response rate to make video appear more vivid and natural. ― Use colour degradation, black level, etc.) may occur, depending on the connected source device. Standard mode when not playing a video or game.
Screen Ratio Screen Adjustment ― Connection Using the HDMI/DP Cable Change the picture size. ― This option is only available when PC/AV Mode is set to AV. mode ― This menu is only available when Screen Ratio is set to Screen Fit Mode.
Chapter 05 Configuring the PIP/PBP Settings Function Key Guide → → PIP/PBP ― The functions available may vary depending on the product model. The colour and shape of parts may Screen Position differ from what is shown. Specifications are subject to change without notice to improve quality. Select the position of the sub-screen from the available options.
Source Contrast Select the source for each screen. Adjust the contrast level. Values closer to 100mean a bigger light/dark contrast. ― This option is available when ― This option is available when PIP/PBP Mode is set to On. PIP/PBP Mode is set to On.
Chapter 06 Adjusting OSD (On Screen Display) settings Function Key Guide → → OnScreen Display ― The functions available may vary depending on the product model. The colour and shape of parts may Language differ from what is shown. Specifications are subject to change without notice to improve quality. Set the menu language.
Chapter 07 Setup and Reset Function Key Guide → → System ― The functions available may vary depending on the product model. The colour and shape of parts may FreeSync differ from what is shown. Specifications are subject to change without notice to improve quality. FreeSync technology is solution that eliminates screen tearing without all the usual lag and latency.
Volume setting. ― If you encounter any issues when using the function, contact the Samsung Service Centre. ― If you change the screen resolution while the function is On, the screen may intermittently blank out due to the graphic card. Set FreeSync and change the resolution.
Off Timer Plus Auto Source Switch By activating, a new connected source is displayed automatically. Configuring Off Timer ― This function may not be supported depending on the model or geographical area. Timer: Turn on Off Timer mode. Turn Off After: The off timer can be set within a range of 1 to 23 hours.
Update software using an update file on a USB device. Self Diagnosis Save the update file (in .bin format) that you downloaded from the Samsung Electronics website (http://www.samsung.com/sec) to a USB device. Connect the USB device to the SERVICE port ( ) on the monitor.
Information View the current input source mode, frequency and resolution that are in use and the current product version. Reset All Return all the settings for the product to the default factory settings.
Easy Setting Box Driver Installation To install the latest version of the product driver, download it from the Samsung Electronics website at http://www.samsung.com. ― You can set the optimum resolution and frequency for this product by installing the corresponding drivers.
Check the following. Customer Service Centre Installation issue ― Before calling Samsung Customer Service Centre, test your product as follows. If the problem persists, contact Samsung Customer Service Centre. The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked.
Page 36
The message Check the cable connection and the settings of the source device. appears. Text is blurry. Check that the cable is properly connected to the product. If using a Windows OS (e.g. Windows 7, Windows 8, Windows 8.1 or Windows 10): Go to Control Panel →...
Q & A ― Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Set the frequency on your graphics card. • Windows 7: Go to Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Screen Refresh Rate under Monitor settings. •...
― The above specifications are subject to change without notice to improve quality. Refer to the label at the back of the product as the standard ― For detailed device specifications, visit the Samsung Electronics website. voltage can vary in different countries.
Standard Signal Mode Table Model Name F27T85* Synchronization Horizontal Frequency 71.3 ~ 117 kHz Vertical Frequency 48 ~ 76 Hz Resolution Optimum Resolution 2560 x 1440 @ 60 Hz Maximum Resolution 2560 x 1440 @ 72 Hz (HDMI) 2560 x 1440 @ 75 Hz (DisplayPort) If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted.
Page 40
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1280 x 1024 79.976 75.025 135.000 VESA, 1440 x 900 55.935 59.887 106.500 VESA, 1600 x 900RB 60.000 60.000 108.000 VESA, 1680 x 1050 65.290 59.954 146.250 VESA, 1920 x 1080 67.500...
• Use of supplies or separately sold product unspecified by Samsung. • Repair from a person besides an engineer of outsourcing service company or partner of Samsung Not a product defect Electronics Co., Ltd. •...
Samsung’s service center has run out of replacement parts and cannot repair the product, Samsung will replace your product at no additional charge. If the model you purchased is no longer available, Samsung replace it with the current equivalent model.