Mitsubishi Electric 700 Series Installation Manualline page 22

Pr. Name
Reference value at
62
acceleration
Reference value at
63
deceleration
65 Retry selection
Stall prevention operation
66
reduction starting frequency
Number of retries at fault
67
occurrence
68 Retry waiting time
69 Retry count display erase
Special regenerative brake
70
duty
71 Applied motor
72 PWM frequency selection
73 Analog input selection
74 Input filter time constant
Reset selection/disconnected
75 PU detection/PU stop
selection
77 Parameter write selection
Reverse rotation prevention
78
selection
79 Operation mode selection
80 Motor capacity
81 Number of motor poles
82 Motor excitation current
83 Rated motor voltage
84 Rated motor frequency
Speed control gain (Advanced
89
magnetic flux vector)
90 Motor constant (R1)
91 Motor constant (R2)
92 Motor constant (L1)
93 Motor constant (L2)
94 Motor constant (X)
96 Auto tuning setting/status
PU communication station
117
number
118 PU communication speed
PU communication stop bit
119
length
PU communication parity
120
check
Number of PU communication
121
retries
PU communication check time
122
interval
PU communication waiting
123
time setting
PU communication CR/LF
124
selection
Terminal 2 frequency setting
125
gain frequency
Initial
Setting Range
Value
0 to 200%, 9999 9999
0 to 200%, 9999 9999
0 to 5 0
0 to 400Hz 60Hz
0 to 10, 101 to
0
110
0.1 to 360s 1s
0 0
0 to 30% 0%
0, 1, 3 to 6, 13 to
16, 23, 24, 40,
0
43, 44, 50, 53,
54
0 to 15 1
0, 1, 10, 11 1
0 to 8 1
0 to 3, 14 to 17 14
0, 1, 2 0
0, 1, 2 0
0, 1, 2, 3, 4, 6, 7 0
0.1 to 15kW,
9999
9999
2, 4, 6, 8, 10,
9999
9999
0 to 500A, 9999
9999
∗4
200V/
0 to 1000V
400V
∗6
10 to 120Hz 60Hz
0 to 200%, 9999 9999
0 to 50Ω, 9999 9999
∗4
0 to 50Ω, 9999 9999
∗4
0 to 1000mH,
9999
9999
∗4
0 to 1000mH,
9999
9999
∗4
0 to 100%, 9999
9999
∗4
0, 1, 11, 21 0
0 to 31 (0 to 247) 0
48, 96, 192, 384 192
0, 1, 10, 11 1
0, 1, 2 2
0 to 10, 9999 1
0, 0.1 to 999.8s,
0
9999
0 to 150ms,
9999
9999
0, 1, 2 1
0 to 400Hz 60Hz
Pr. Name
Terminal 4 frequency setting
126
gain frequency
PID control automatic
127
switchover frequency
128 PID action selection
129 PID proportional band
130 PID integral time
131 PID upper limit
132 PID lower limit
133 PID action set point
134 PID differential time
145 PU display language selection 0 to 7
146 Parameter for manufacturer setting. Do not set.
Acceleration/deceleration time
147
switching frequency
150 Output current detection level
Output current detection signal
151
delay time
152 Zero current detection level
153 Zero current detection time
Stall prevention operation
156
selection
157 OL signal output timer
158 AM terminal function selection
160 User group read selection
Frequency setting/key lock
161
operation selection
Automatic restart after
162 instantaneous power failure
selection
Stall prevention operation level
165
for restart
168
Parameter for manufacturer setting. Do not set.
169
170 Watt-hour meter clear
171 Operation hour meter clear
User group registered display/
172
batch clear
173 User group registration
174 User group clear
178 STF terminal function selection
STR terminal function
179
selection
PARAMETER LIST
Initial
Setting Range
Value
0 to 400Hz 60Hz
0 to 400Hz, 9999 9999
0, 20, 21, 40 to
43, 50, 51, 60,
61
0.1 to 1000%,
100%
9999
0.1 to 3600s,
9999
0 to 100%, 9999 9999
0 to 100%, 9999 9999
0 to 100%, 9999 9999
0.01 to 10.00s,
9999
9999
0 to 400Hz, 9999 9999
0 to 200% 150%
0 to 10s
0 to 200% 5%
0 to 1s 0.5s
0 to 31, 100, 101
0 to 25s, 9999
1 to 3, 5, 7 to 12,
14, 21, 24, 52,
53, 61, 62
0, 1, 9999
0, 1, 10, 11
0, 1, 10, 11
0 to 200% 150%
0, 10, 9999 9999
0, 9999 9999
9999, (0 to 16)
0 to 999, 9999 9999
0 to 999, 9999 9999
0 to 5, 7, 8, 10,
12, 14 to 16, 18,
24, 25, 60, 62,
65 to 67, 9999
0 to 5, 7, 8, 10,
12, 14 to 16, 18,
24, 25, 61, 62,
65 to 67, 9999
0
1s
1
0s
0
0s
1
0
0
1
0
60
61
19