Advertisement
2. INtroDuctIoN
durable composite housing operated by simple pull and release action. features integral manual thermal switch to prevent overload and led
power indicator. supplied with single socket outlet.
3. specIFIcatIoN
model no: .................................................. CRM101/CRM151
supply: ...........................................................................230V
cable length: .......................................................10mtr/15mtr
cable section: ......................................................... 3 x 1mm²
thermal trip: ..................................................................... yes
capacity wound:..........................................................1000W
capacity unwound: ..........................................1500W/1400W
4. mouNtING/assembly
4.1.
fix the cable reel in an appropriate position, ensuring that the wall and the mounting bolts will adequately support the weight of the
reel and the tension of the cable, as it is pulled from the reel.
4.2.
using the bracket as a template, mark the position, on the wall where the cable reel is to be mounted, for two holes. drill two 10mm
diameter holes in the wall of sufficient depth to take the masonry bolts supplied.
4.3.
Insert the two masonry bolts into the holes and mount the bracket onto the studs and loosely secure with the flat washers,
spring washers and the nuts supplied. tighten the nuts evenly until the bracket and reel are secure.
4.4.
ensure that the cable can be pulled out to, and reeled back from, work sites without rubbing on the sides of the cable entry.
5. operatIoN
5.1.
extending the cable.
5.1.1.
As the cable is pulled out from the reel, the action of the ratchet mechanism can be heard alternating between a clicking sound and a
short silent period. if the tension on the cable is released whilst the ratchet is clicking, the cable will remain extended.
5.1.2.
if the tension on the cable is released during the silent period, the cable will retract. to stop the cable retracting, pull it out again
until the ratchet starts clicking, and then release it.
5.2.
retracting the cable.
5.2.1.
to release the cable and allow it to automatically rewind, pull the cable out from the locked position until the clicking stops and then
release the tension on the cable. Do Not let go of the cable, but guide it back smoothly until the socket is back in the reel.
WarNING! The reel tension is factory set, if any adjustment is required, contact an authorised service agent. Do Not remove any
‰
of the cover screws.
5.3.
thermal cut-out.
5.3.1.
in the event of the reel being overloaded, the cut-out switch will trip. if this occurs, disconnect the reel from the supply and then
determine and rectify the cause of the overload.
5.3.2.
reconnect to the supply and press the cut-out reset button - after allowing two to three minutes for cooling down.
eNVIroNmeNt protectIoN
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Weee reGulatIoNs
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
sealey Group, kempson Way, suffolk business park, bury st edmunds, suffolk. Ip32 7ar
01284 757500
© Jack sealey limited
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
cRM101, CRM151| Issue:2 (L) 05/09/17
Advertisement
