Sealey HFC08.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETy
WARNING! Wear protective gloves and approved safety eye protection (standard spectacles are not adequate).
‰
WARNING! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
DO NOT allow untrained persons to use the filter crusher.
8
DO NOT operate the filter crusher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT operate the filter crusher if parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT use the filter crusher for a task it is not designed to perform.
8
DO NOT crush aerosol cans, cylinders of compressed gas, fuel filters or containers of flammable liquids or solvents.
8
DO NOT smoke when using crusher.
8
DO NOT modify the crusher or alter the operation in any way to circumvent the interlocking door mechanism.
8
Place oil filters into the crushing chamber open side down.
9
Maintain the filter crusher in good condition. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and invalidate the warranty.
Familiarise yourself with the applications, limitations and potential hazards of the filter crusher.
9
Keep work area clean, uncluttered and ensure there is adequate lighting.
9
Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip footwear.
9
Keep the filter crusher clean for best and safest performance.
9
When not in use release pressure from the filter crusher.
9
Wear appropriate clothing such as overalls.
9
Keep untrained/unauthorised personnel away from filter crusher.
9
Clean up any spilled oil immediately so it will not cause a slipping hazard.
9
If the unit has to be re-sited it should be moved with the crushing module in the lowered position.
9
2. INTRODUCTION
Reduce your waste disposal costs* - crushing filters minimises the volume of your hazardous waste. Air operated oil filter press with safety lock-
out device which prevents the door being opened during operation. Floor mounting unit with outlet for waste oil transfer.
* For disposal by volume customers.
3. SPECIFICATION
Capacity: ................................................................... 10tonne
external Size (H x W x d): ......................880 x 550 x 335mm
Internal Size (H x W x d):........................280 x 190 x 190mm
Maximum Filter Capacity (Height x Ø): .............216 x 152mm
nett Weight: ............................................................ 113.00Kg
Pressing Time: ............................................................. 30sec
Supply: ................................................................. 100-190psi
4. ASSEMbLy
WARNING! The unit is very heavy and should only be moved
‰
with a crane or forklift truck.
4.1. LOCATION AND ASSEMbLy
locate the crusher in a suitable place indoors on firm and level
concrete.
4.1.1. Firstly the stand must be assembled. Attach the two legs
(Fig.1C) to the cross beam (Fig.1e) using two bolts
washers and nuts either side. ensure that upright
supports (Fig.1B) are secured with the far nut (Fig.1d) on each
leg.
4.1.2. Place the upright on the crossbeam (Fig.1e) aligning with the pre-drilled holes. ensuring it is the correct way around with the lip over
the back of the cross beam. Secure with two bolts, washers and nuts vertically through the cross beam and two horizontally through
the lip of the upright.
© Jack Sealey limited
PNEUMATIC FILTER CRUSHER
Model no:
Wear protective
gloves
Original Language Version
HFC08.V2
fig.1
HFC08.V2 Issue 2 (HF) 10/10/18