Panasonic FX-502 Series Instruction Manual

Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for the correct and
optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
WARNING
Never use this product as a sensing device for personnel protection.
In case of using sensing devices for personnel protection, use products which
meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel
protection applicable in each region or country.
INTENDED PRODUCTS FOR CE MARKING
1
This product complies with the following standards / regulations.
EMC Directive
<Standards in US / Canada>
ANSI/UL 60947-5-2, CAN/CSA C22.2 No.14
Caution about UL recognition
In case requiring conformity of UL listing mark or C-UL listing mark, USe class
2 power supply unit.
2 PART DESCRIPTION
Sensing output 2 UP key
selection indicator
• Teaching
• Threshold value
Sensing output 1
selection indicator
• Select setting items
Sensing output 1
Digital display
operation indicator
(Orange)
Sensing output 2
operation indicator
(Orange)
<Reference>
Pressing down SET key + MODE key for 3 sec : Set key lock or release key lock
3 MOUNTING
How to connect
1. Fit the rear part of the mounting sec-
2. Press down the rear part of the
mounting section of the unit on the
DIN rail and fit the front part of the
mounting section to the DIN rail.
1. Push the controller forward.
2.
to remove it.
1. Snap the fiber lock lever down till it
stops completely.
2.
inlets until they stops. (Note)
3. Return the fiber lock lever to the
original position till it stops.
Note:
or FD-FM2
into the beam-receiving inlet. If they are inserted in
reverse, the sensing performance will deteriorate.
4 INSTALL MORE AMPLIFIER OF SERIES CONNECTION TYPE
Make sure that the power supply is OFF while adding or removing the series connection type.
In case 2 or more the series connection types are connected in cascade, make
sure to mount them on a DIN rail.
using a main connection cable.
When connecting 2 or more the series connection types in cascade, use the
sub cable (optional) for the second series connection type onwards.
INSTRUCTION MANUAL
FX-502
MJE-FX502C No.0068-84V
SET key DOWN key
• Teaching • Teaching
• C o n f i r m s e t t i n g •
contents adjustment
• Select setting items
MODE key
• Select Modes
• Cancel during setting
• Select sensing output 1/2
by pressing long
2. Press down
35mm width DIN rail
1. Push forward
2. Lift up
3. Return
1. Snap
Fiber lock lever
Fiber for emitter
2. Insert
FD-G4
Fiber for
receiver
How to cascade
1.
on the DIN rail.
2.
other, and connect the quick-
connection cables.
3. Mount the end plates MS-DIN-E
(optional) at both the ends to hold
the amplifiers between their flat
sides.
4.
plates.
1. Loosen the screws of the end
plates.
2. Remove the end plates.
3. Slide the amplifiers and remove
them one by one.
5 I/O CIRCUIT DIAGRAMS
<FX-502>
<FX-502P>
Note: The quick-connection sub cable does not incorporate +V (brown) and 0V (blue). The power is supplied from
the connector of the main cable.
1
4
2
3
6 OPERATION PROCEDURE
The sensing output can be switched to sensing output 1 or sensing output 2
by holding down the mode key.
1. Fit
The changed settings are not stored if turning the power OFF while setting.
power OFF.
When turning ON the power, RUN mode is displayed and the digital display
shows the threshold value (green) and the incident light intensity (red).
<RUN mode>
<Sensing output operation mode>
<CUSTOM mode>
<PRO mode>
<RUN mode>
MOUNTING."
Communication
window
End plate
MS-DIN-E (Optional)
End plate
MS-DIN-E
(Optional)
(Brown) +V (Note)
(White) Sensing output 2 / External input
Load
(Black) Sensing output 1
(Blue) 0V (Note)
(Brown) +V (Note)
(Black) Sensing output 1
(White) Sensing output 2 / External input
Load
(Blue) 0V (Note)
Terminal No. Terminal name
1 +V
2 Sensing output 1
3 Sensing output 2 / External input
4 0V
• Displays threshold value (green) and incident light intensity (red).
•
can be set.
• For setting method of each function, refer to "
MODE," " THRESHOLD VALUE FINE ADJUSTMENT FUNC-
TION," or " KEY LOCK FUNCTION."
• Select either Light-ON or Dark-ON.
• For the setting, refer to " SENSING OUTPUT OPERATION
MODE."
• The default setting is " " (Light-ON).
• An item set in CUSTOM mode (Response time setting, Emission
power setting and Hysteresis setting) is displayed.
• For details, refer to " CUSTOM MODE."
• The default setting is " " (response time setting).
• Advanced setting can be done.
• For the setting, refer to " PRO MODE."
Sub cable
(Optional)
Slide
Main cable
(Optional)
Slide
+
12 to 24V DC
%
-
+
12 to 24V DC
%
-
TEACHING