Page 1 If you need assistance, use one of the following: ❖ Toshiba’s Support Website pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 153 in this guide.
Page 2 AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA OR...
Page 3 Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port and microphone jack.
Page 4: Industry Canada Requirement
Contact either: ❖ Toshiba’s Support Website at pcsupport.toshiba.com. ❖ Or call the Toshiba Global Support Centre: Within the United States at (800) 457-7777. Outside the United States at (949) 859-4273. Industry Canada requirement This Class B digital apparatus complies with Canadian ICES-003.
Page 5: Telephone Company Procedures
If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273.
Page 6 provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer. Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm...
Page 7: Wireless Interoperability
USOC RJ11C. Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖...
Page 8: Wireless Lan And Your Health
Wireless LAN device prior to turning on the equipment. Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 9 Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prêt à...
Page 10 Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze TOSHIBA Corp. Digital Media Network Company dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.
Page 11 Caution: Exposure to Radio Frequency Radiation The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 12 Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
Page 13: Device Authorization
The interference range of this equipment is less than 40m. 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100...
Page 14: Radio Approvals For Wireless Devices
Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use only. Radio approvals for wireless devices NOTE The following information is dependent on what type of wireless device is in...
Page 15 Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique: 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 16 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Europe - Restrictions for use of 5 GHz Frequencies in European Community Countries European Community Countries Austria Belgium, France, Switzerland/Lichtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK...
Page 17 ❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
Page 18 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Approved Countries/Regions for use for the Intel Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table.
Page 19 Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 20: Bluetooth Wireless Technology Interoperability
Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
Page 21: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 22 The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 23 Taiwan Article 14 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Article 17 Any use of low power radio frequency electric machinery shall not affect aviation safety and interfere with legal communications.
Page 24 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 25 Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
Page 26 Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 27 ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wireless Capability Ethernet Alliance. Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories. TouchPad is a trademark of Synaptics, Inc.
Page 28: Table Of Contents
Other precautions ...44 Important information on your computer’s Setting up your computer ...47 Setting up your software...48 Registering your computer with Toshiba ...49 Setting up other devices ...49 Connecting to a power source ...49 Charging the main battery...52 cooling fan ...46...
Page 29 Using the computer for the first time ...53 Opening the display panel ...53 Your computer’s features and specifications ...54 Turning on the power ...55 Adding memory ...56 Installing a memory module ...56 Removing a memory module...60 Using the TouchPad™...62 Scrolling with the TouchPad™ ...63 Control buttons ...63 Disabling or enabling the TouchPad ...63 Turning off the computer ...65...
Page 30 Backing up your work ...95 Restoring your work ...96 Powering down the computer ...96 Using the Turn off computer or Shut down Shutting down more quickly ...98 Using Hibernation Mode ...99 Using Standby Mode...102 Toshiba’s online resources ...105 command...97 ® Explorer...83...
Page 31 Chapter 3: Mobile Computing...106 Toshiba’s energy-saver design...106 Running the computer on battery power ...107 Battery Notice ...107 Charging the batteries...108 Charging the main battery...109 Charging the RTC battery...110 Monitoring main battery power...111 Determining remaining battery power...111 What to do when the battery runs low ...112 Setting battery alarms...113...
Page 32 Setting a supervisor password...146 Deleting a supervisor password...147 Using the TOSHIBA Zooming Utility...147 Using the TOSHIBA Touch and Launch utility ...148 Chapter 6: If Something Goes Wrong...153 Problems that are easy to fix ...153 Problems when you turn on the computer...155 The Windows Using Startup options to fix problems ...157...
Page 33 Modem problems...177 Develop good computing habits ...178 If you need further assistance...179 Before you call ...179 Contacting Toshiba ...180 Other Toshiba Internet Web sites ...181 Toshiba’s worldwide offices...181 Appendix A: Hot Keys... 183 Volume Mute ...183 Instant password security...184 Stand By mode ...184 Hibernation mode ...185...
Page 34 Contents Appendix B: Power Cord/Cable Connectors...189 Appendix C: Using ConfigFree™ with your Toshiba Computer...190 Getting Started...191 Starting ConfigFree ...191 ConfigFree Utilities...192 Connectivity Doctor ...192 Search for Wireless Devices ...195 Profile Settings ...196 Quick Connect...198 Using the Automatic Switch...201 Semi-Automatic Switch Feature ...202 Glossary...203...
Page 35: Introduction
Toshiba's Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, and system/ component/options availability are all subject to change without notice.
Page 36: This Guide
Introduction This guide This guide This guide introduces the computer’s features. You can: ❖ Read the entire guide from beginning to end. ❖ Skim through and stop when a topic interests you. ❖ Use the table of contents and the index to find specific information.
Page 37: Other Icons Used
Your computer comes with the following documentation: ❖ An electronic version of the user’s guide. ❖ It may also contain guides for other programs that may come with your system. For accessory information, visit Toshiba's Web site at accessories.toshiba.com. Introduction Other documentation...
Page 38: Service Options
Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see Something Goes Wrong” on page 153.
Page 39: Chapter 1: Getting Started
Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your computer. Selecting a place to work Your computer is designed to be used in a variety of locations and situations.
Page 40 Getting Started Selecting a place to work To keep your computer in prime operating condition, protect your work area from: ❖ Dust, moisture, and direct sunlight ❖ Liquids and corrosive chemicals Never allow any liquids to spill into any part of your PC, and never expose the PC to rain, water, seawater, or moisture.
Page 41: Keeping Yourself Comfortable
Keeping yourself comfortable Strain and stress injuries are becoming more common as people spend more time using their computers. However, with a little care and the proper use of the equipment, you can work comfortably throughout the day. Using the computer keyboard incorrectly can result in discomfort and possible injury.
Page 42 Getting Started Selecting a place to work Seating and posture When using your computer, maintain good posture with your body relaxed and your weight distributed evenly. Proper seating is a primary factor in reducing work strain. Some people find a backless chair more comfortable than a conventional chair.
Page 43 Lighting Proper lighting can improve the readability of the display and reduce eyestrain. ❖ Position the display panel or external monitor so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare. ❖...
Page 44: Other Precautions
Getting Started Selecting a place to work ❖ Avoid performing repetitive activities for long periods. Intersperse such activities with other tasks. ❖ Focusing your eyes on your computer screen for long periods can cause eyestrain. Look away from the computer frequently and focus your eyes on a distant object for at least 30 seconds.
Page 45 Never allow any liquids to spill into any part of your PC, and never expose the PC to rain, water, seawater, or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately: 1.
Page 46: Important Information On Your Computer's Cooling Fan
Getting Started Selecting a place to work ❖ Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers. Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files. Handle discs carefully.
Page 47: Setting Up Your Computer
The cooling fan location will vary depending on the computer. NOTE Setting up your computer TECHNICAL NOTE: You must complete all setup steps up to and including adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards.
Page 48: Setting Up Your Software
Getting Started Setting up your computer Setting up your software NOTE The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices. The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software.
Page 49: Registering Your Computer With Toshiba
If you opt not to register at that time, you can either double-click the icon on your desktop or go to the Toshiba Web site at www.register.toshiba.com. Customer failure to complete Product Registration will not diminish Customer rights under this limited Warranty.
Page 50 Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.
Page 51 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Plug the AC adapter cord into the DC-IN on the right side of the computer.
Page 52: Charging The Main Battery
Getting Started Charging the main battery Damaged power cords/cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cord/cable. If the power cord/cable becomes damaged or the plug over- heats, discontinue use.
Page 53: Using The Computer For The First Time
TECHNICAL NOTE: The RTC battery does not charge while the computer is turned off, even when AC power is attached. The RTC battery charges when the computer is powered on. Battery life and charge time may vary depending on the NOTE applications, power management settings, and features used.
Page 54: Your Computer's Features And Specifications
Getting Started Using the computer for the first time Small bright dots may appear on your TFT display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
Page 55: Turning On The Power
Turning on the power To turn on the computer: Make sure any external devices (such as the AC adapter, if you plan to use AC power rather than battery power) are properly connected and ready. Check to ensure that all drives are empty. Press and hold the power button in until the on/off light on the system indicator panel glows green—about one second.
Page 56: Adding Memory
For more information on memory options, check the accessories information that came with your computer, or visit accessories.toshiba.com. Installing a memory module Additional memory modules can be installed in the memory module slots on the base of the computer. You will need a standard Phillips no.1 screwdriver for this procedure.
Page 57 The computer has two memory module slots — Slot A and Slot B. You can install one or two memory modules. Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost.
Page 58 Getting Started Adding memory Using a standard Phillips no. 1 screwdriver, unscrew the screw that secures the memory module slot cover. Unscrewing the memory module slot cover Remove the memory slot cover. Place the screw and the cover in a safe place so that you can retrieve them later.
Page 59 Do not force the memory module into position. The memory module should be level when secured in place. Sample inserting the memory module into the slot The clips on either side of the memory module will click to secure the memory module. Avoid touching the connectors on the memory module or on the computer.
Page 60: Removing A Memory Module
Getting Started Adding memory If you are adding an extra memory module after setting up the computer, verify that the computer has recognized it correctly as described in Removing a memory module To remove the memory module: Turn the computer off and remove all cables connected to the computer, including the AC adapter cable.
Page 61 Carefully remove the module from the slot. Sample removing the memory module Replace the memory module slot cover and screw. Turn the computer over and restart it. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory module, you can check that the computer has recognized the change.
Page 62: Using The Touchpad
Getting Started Using the TouchPad™ Using the TouchPad The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you would like to move the cursor: ❖...
Page 63: Scrolling With The Touchpad
Scrolling with the TouchPad There are two active regions on the TouchPad that allow you to scroll as you would with any wheel device on a mouse or trackball. To scroll vertically, run your finger up or down along the right edge of the TouchPad.
Page 64 Getting Started Using the TouchPad™ Sample TouchPAD ON/OFF screen Select Disable or Enable, whichever is appropriate. Click Apply. Click OK. The Mouse Properties window closes. Close the Printers and Other Hardware window. Close the Control Panel window. The Fn + F9 shortcut can be used to enable or disable the NOTE TouchPad.
Page 65: Turning Off The Computer
Turning off the computer It is a good idea to turn off your computer when you are not using it for a while. If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery.
Page 66: Closing The Display Panel
Getting Started Using external display devices Closing the display panel When you are finished, shut the computer down and close the display panel to keep dust and dirt out of the computer. If you close the computer while it is still on, these actions will occur: ❖...
Page 67: Directing The Display Output When You Turn On The Computer
Turn on the external device. Set the display mode by pressing configuring the Display Properties settings. Directing the display output when you turn on the computer Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously.
Page 68: Adjusting The Quality Of The External Display
Getting Started Using an external keyboard Adjusting the quality of the external display To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
Page 69: Connecting A Local Printer
Connecting a local printer Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly.
Page 70: Setting Up Your Printer
Getting Started Setting up your printer Setting up your printer If you started your computer with a printer connected and turned on, it may have been detected automatically (Plug and Play). If this is not the case, then you must install the printer driver for the model of printer that is connected to your computer.
Page 71 Sample Add Printer Wizard Click Next. The Add Printer Wizard asks you to select your printer. TECHNICAL NOTE: If your printer is Plug and Play, the operating system recognizes it automatically. You can ignore the remainder of this section. See your printer manual. If the printer you are setting up: ❖...
Page 72 Getting Started Setting up your printer From the list of manufacturers and printers, select your printer, then click Next. Select the port settings according to the instructions in your printer’s documentation and the port to which your printer is connected, then click Next. The Add Printer Wizard prompts you to enter a printer name.
Page 73: Connecting An Optional External Diskette Drive
Connecting an optional external diskette drive Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5- inch diskettes. Sample optional external USB diskette drive To connect an optional external USB diskette drive, connect the cable to one of the computer’s USB ports.
Page 74: Cleaning The Computer
To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer for suggestions for appropriate cleaning products. Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the drive indicator light stops glowing) and all external peripheral cables are disconnected.
Page 75 Sample PORT-Noteworthy To secure the computer: Loop the cable through or around some part of a heavy object. Make sure there is no way for a potential thief to slip the cable off the object. Pass the locking end through the loop. Insert the cable’s locking end into the security lock slot on the back of the computer, then give the key a quarter turn and remove it.
Page 76: Chapter 2: Learning The Basics
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the disk. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Page 77 ❖ Back up your files to disks (or other removable media) on a regular basis. Label the backup copies clearly and store them in a safe place. It’s easy to put off backing up because it takes time. However, if your hard disk suddenly fails, you will lose all the data on it unless you have a separate backup copy.
Page 78: Using The Keyboard
Learning the Basics Using the keyboard Using the keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows the functionality of a full-size keyboard. Sample keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖...
Page 79: Making Your Keyboard Emulate A Full-Size Keyboard
Making your keyboard emulate a full-size keyboard Although your computer’s keyboard layout is compatible with a standard full-size keyboard, it has fewer keys. A standard full-size keyboard has two editing keys; cursor positioning keys; and a numeric keypad. Pressing the of the specially marked keys allows you to emulate a full-size keyboard.
Page 80: Windows Special Keys
Learning the Basics Using the keyboard through programmed functions when pressed. Used in combination with the specific functions on the computer. For example, off the TouchPad. For more information, see page 183. Windows special keys Sample Windows special keys Your computer’s keyboard has two keys that have special functions in Windows: ❖...
Page 81: Using The Overlay To Type Numeric Data
Sample numeric overlay Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys. To turn the numeric overlay on, press simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on. You can still use the overlay keys to type alphabetic characters while the numeric overlay is on.
Page 82: Starting A Program
Learning the Basics Starting a program Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows If you prefer to open the program first, you have four options.
Page 83: Starting A Program From Windows Explorer
Starting a program from Windows If a program is not listed in the Programs menu, you can start it from Windows view of your computer’s contents as a hierarchy or “tree.” You can easily see the content of each drive and folder on your computer.
Page 84: Starting A Program From The Run Dialog Box
Learning the Basics Starting a program Starting a program from the Run dialog box This example uses the Run command to start WordPad: Click Start, then click Run. The Run dialog box appears. Sample Run dialog box In the Run dialog box: ❖...
Page 85: Saving Your Work
Saving your work Before you turn off the computer, save your work on the hard disk drive or diskette/CD. This is one of the most important rules of computing. TECHNICAL NOTE: Save your data even when you are using the Standby command, in case the main battery discharges before you return to work.
Page 86: File Names
Learning the Basics Saving your work Sample Save As dialog box Choose the drive and folder where you want your file to be stored. Type a file name, then click Save. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
Page 87: Printing Your Work
Using a file extension Most programs assign an extension to the file name that identifies the file as being created in the program with a particular format. For example, Microsoft with a .doc extension. Any file name with an extension of “.doc”...
Page 88: Using The Dvd-Rom Or Multi-Function Drive
Learning the Basics Using the DVD-ROM or multi-function drive The program displays a Print dialog box. Sample Print dialog box Specify the print parameters. For example, the range of pages and number of copies to print. Click Print. Using the DVD-ROM or multi-function drive Optical storage has become the preferred medium for software, music, and video.
Page 89: Drive Components And Control Buttons
Using the DVD-ROM or multi-function drive TECHNICAL NOTE: Your DVD-ROM or multi-function drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region. The drive will allow you to change regions four times.
Page 90: Cd/Dvd Control Buttons
Learning the Basics Using the DVD-ROM or multi-function drive Do not press the eject button or turn off the computer while the Drive in-use indicator light is glowing. Doing so could damage the disc or the drive. When the disc tray is open, be careful not to touch the lens or the area around it.
Page 91: Inserting A Compact Disc
Using the DVD-ROM or multi-function drive The next track button skips to the following track on the disc. The play/pause button starts playing the disc or makes it pause if currently playing. The stop/eject button stops a disc that is currently playing. You can eject a disc by pressing the stop/eject button twice.
Page 92 If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
Page 93: Removing A Disc With The Computer On
Using the DVD-ROM or multi-function drive Removing a disc with the computer on To remove a compact disc (CD or DVD) with the computer turned on: Press the eject button on the drive. Do not press the eject button while the in-use indicator light is glowing.
Page 94: Using Pc Cards
Learning the Basics Using PC Cards ❖ Do not apply a label to or otherwise mar the surface of a disc. ❖ Hold a disc by its outside edge. Fingerprints on the surface can prevent the DVD-ROM drive or multi- function drive from reading the data properly.
Page 95: Using Your Computer At The Office
❖ Do not remove a hard disk card while the system is accessing it. ❖ Do not remove a network card while you are connected to a network. ❖ Do not remove a SCSI card while any of the SCSI devices connected to it are operating.
Page 96: Restoring Your Work
Learning the Basics Powering down the computer HINT: Backing up all the files on your hard disk takes a considerable amount of time and many diskettes. You may prefer to use a high-capacity backup system, such as an external tape drive. Restoring your work To restore information from your backup media to your hard disk, use the Restore page in the backup program.
Page 97: Using The Turn Off Computer Or Shut Down Command
TECHNICAL NOTE: Before using any of these options to power down your computer, save your files and make sure the disk activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again. Using the Turn off computer or Shut down command For the Windows steps to shut down the computer:...
Page 98: Shutting Down More Quickly
Learning the Basics Powering down the computer The computer shuts down completely. To change the Stand By button to hibernate, hold the Shift key NOTE while the Turn Off computer Windows dialog box is open. For more information about setting up hibernation refer to Hibernation Mode”...
Page 99: Using Hibernation Mode
Sample Power Options Advanced tab Click Apply. Click OK, then close the Control Panel. Starting again after Turn Off To start the computer up again, press and release the power button. The on/off light turns on. If you shut down the computer by closing the display panel, you can start it again by opening the display panel.
Page 100 Learning the Basics Powering down the computer Factors when choosing Hibernation mode: ❖ While in Hibernation mode, the computer uses no battery power. ❖ Because the state of the system is held on the hard disk, no data is lost if the battery discharges. ❖...
Page 101: Using Hibernation
Click Apply. Click OK, then close the Control Panel. The computer is now set to automatically enter into Hibernation when your option settings occur. Once the computer is configured, place the computer into Hibernation mode by either pressing the power button or closing the display panel, depending on the hibernation options selected.
Page 102: Using Standby Mode
Learning the Basics Powering down the computer Starting again from Hibernation mode Use these instructions to restart the computer when you enter Hibernation mode by closing the display panel: ❖ AC power. Open the display panel. ❖ Battery power. Open the display panel and press the power button until the on/off light changes to green.
Page 103: Using Standby
To power down the computer using the Standby command, click Start, Turn off computer, and select Stand By. Sample Turn off computer Windows dialog box If you hold down the Shift key, Stand By becomes Hibernate in NOTE the Turn off computer dialog box. To enter hibernation mode, you must hold down the Shift key while you select Hibernate.
Page 104 You can also specify an amount of time after which the computer automatically enters into Standby mode. To use any of these methods, you first need to enable them in Toshiba’s Power Management utility. Click Start, Control Panel. Double-click the Power Options icon.
Page 105: Toshiba's Online Resources
The computer returns tot he screen you were previously using. Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions and keep you up to date with future upgrades.
Page 106: Chapter 3: Mobile Computing
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while...
Page 107: Running The Computer On Battery Power
It may not function efficiently over the expected life of the battery and the battery light may not indicate a low-battery condition. For optimum DVD performance, Toshiba recommends that you NOTE play DVDs while running on AC power rather than on battery power.
Page 108: Charging The Batteries
Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your notebook computer. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com.
Page 109: Charging The Main Battery
Charging the main battery To charge the battery, plug the computer into a live wall outlet. It takes several hours to charge the battery with the computer off. It takes much longer to charge the battery while the computer is on. TECHNICAL NOTE: When your computer is using all of the power provided by the AC Adapter to run applications, features, and devices, the recharging of the battery cannot...
Page 110: Charging The Rtc Battery
Mobile Computing Charging the batteries Charging the RTC battery Your computer has an internal real-time clock (RTC) battery. The RTC battery powers the System Time Clock and BIOS memory used to store your computer’s configuration settings. When fully charged, it maintains this information for up to a month when the computer is powered off.
Page 111: Monitoring Main Battery Power
Monitoring main battery power The computer’s main battery light gives you an indication of the main battery’s current charge: ❖ Glows amber while the main battery is being charged (AC adapter connected). ❖ Glows green when the main battery is fully charged. ❖...
Page 112: What To Do When The Battery Runs Low
Mobile Computing Monitoring main battery power Sample Power Management Options Power Meter tab TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 50 degrees Fahrenheit. The computer calculates the remaining battery charge based on your current rate of power use and other factors such as the age of the battery.
Page 113: Setting Battery Alarms
Hibernate mode keeps track of where you were so, when you turn on the power again, you can continue where you left off. The computer stores the information on what you were doing until the battery runs out of power. If you have Hibernate mode enabled (the default), the computer copies the details of your open programs and files to the hard disk before shutting down.
Page 114: Conserving Battery Power
Mobile Computing Monitoring main battery power Sample Power Options Alarms tab Conserving battery power How long a fully charged battery lasts when you are using the computer depends on a number of factors, such as: ❖ How the computer is configured ❖...
Page 115: Changing Batteries
Changing batteries When handling battery packs, do not drop or knock them. Also, be careful not to damage the casing or short-circuit the terminals. To change the battery: Save your work. Shut down and turn off the computer. Remove all cables connected to the computer. Turn the computer over.
Page 116 Mobile Computing Changing batteries Sample removing the battery from the computer If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in Wipe the terminals of the charged battery with a clean cloth to ensure a good connection.
Page 117: Taking Care Of Your Battery
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries.
Page 118: Maximizing Battery Life
Mobile Computing Taking care of your battery ❖ When you install the battery pack, you should hear a click when it is seated properly. ❖ Do not expose the battery pack to fire. The battery pack could explode. Maximizing battery life To maximize the life of your battery pack: ❖...
Page 119: Disposing Of Used Batteries
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by Toshiba. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under federal, state and local laws, it may be illegal to dispose of old batteries by placing them in the trash.
Page 120: Conserving Power
Toshiba has combined these options into preset power profiles. Using one of these profiles lets you choose between maximum power savings and peak system performance. You may also set individual power-saving options to suit your own needs.
Page 121: Chapter 4: Exploring Your Computer's Features
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your Satellite Exploring the desktop The desktop is the launching pad for everything you can do in ® the Windows features to start programs, find documents, set up system components, and perform most other computing tasks.
Page 122: Finding Your Way Around The Desktop
Exploring Your Computer’s Features Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, system tray, and background pattern. Icons Start button Sample Windows Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Page 123 Recycle Bin — Holds files you have deleted. You may be able to retrieve these files until you empty the Recycle Bin. TECHNICAL NOTE: If you delete a file from a diskette, it does not go into the Recycle Bin. For more information on the Recycle Bin, see Windows online Help.
Page 124: Setting Up For Communications
Exploring Your Computer’s Features Setting up for communications Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to quickly switch between the programs or windows.
Page 125 Exploring Your Computer’s Features Determining the COM port Your modem is connected to one of the computer’s COM (communications) ports. The default setting for the modem is COM3. The following procedure is intended to support you if you need to either upgrade your modem or reset the port to the default settings.
Page 126: Connecting The Modem To A Telephone Line
Exploring Your Computer’s Features Setting up for communications Click OK to close the properties dialog box for that specific modem. Click OK to close the Modem Properties dialog box. Close the Control Panel. Connecting the modem to a telephone line Before you can communicate using the modem, you need to connect it to a telephone line.
Page 127: Connecting Your Computer To A Network
The modem is designed for use with a standard analog telephone line. Do not connect the modem to a digital telephone line. A digital line will damage the modem. Now you are ready to send a fax or use the modem to connect to an online service or the Internet.
Page 128 Exploring Your Computer’s Features Setting up for communications Enter the phone number of your network connection and let the program dial the number. The computer connects to the network. Using the Ethernet LAN Port When your computer starts, Windows attempts to contact a Dynamic Host Configuration Protocol (DHCP) server.
Page 129: An Overview Of Using The Internet
Using Wireless LAN Connectivity The transmission speed over the wireless LAN and the NOTE distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed.
Page 130: The Internet
Exploring Your Computer’s Features An overview of using the Internet The Internet The Internet is an association of thousands of networks and millions of computers around the world connected by communications lines. They all work together to share information. The World Wide Web The World Wide Web (or “Web”) is a subset of the Internet —...
Page 131: Connecting To The Internet
Connecting to the Internet To connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A Web browser ❖ An Internet Service Provider (ISP) account The Microsoft automatically configured on your system so that when you first start it, it guides you through signing up for a new ISP account, or assists you in setting up your computer to work with your existing ISP.
Page 132: Internet Features
Exploring Your Computer’s Features An overview of using the Internet You can also use a Search Engine, a Web site specifically designed to help you look for information. Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖...
Page 133: Uploading To, And Downloading Files From, The Internet
Uploading to, and downloading files from, the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer to a site on the Web), or downloading (transferring data from a site on the Web to your computer). There are several ways to upload or download data.
Page 134: Playing Cds Using Auto-Run
Exploring Your Computer’s Features Exploring audio features Sample Windows Media Player screen The CD Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/pause button on the CD Player control panel. ❖...
Page 135: Creating A Cd
The disc drive will run the CD. If your disk does not run using this method, try using an application that is associated with the media on the disk. For example, if it is a music CD, open Windows and point it to play the CD. For other types of media, use the associated software to open the files on the disk.
Page 136: Using A Microphone
Exploring Your Computer’s Features Exploring audio features Using a microphone Connect an external microphone to the computer. Click Start, point to All Programs, Accessories, Entertainment, then click Sound Recorder. Positioning Sample Sound Recorder screen Click the Record button. Speak normally into the microphone. When you have finished recording, click the Stop button.
Page 137: Using External Speakers Or Headphones
Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers. Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears.
Page 138: Inserting And Removing Pc Cards
Exploring Your Computer’s Features Inserting and removing PC Cards Inserting and removing PC Cards Your Satellite slot and supports two types of PC Cards: ❖ Type I cards—You can install one of these cards. ❖ Type II cards—You can install one of these cards. Inserting a PC Card Use caution when lifting or turning your computer.
Page 139: Chapter 5: Toshiba Utilities
Your computer includes several utilities designed to help you to reconfigure your system to best meet your individual needs. Together, these allow you to determine certain system details, set additional options, or change default options. This chapter describes the utilities supplied by Toshiba: ❖ Hotkey utility ❖...
Page 140: Toshiba Console
Toshiba Utilities TOSHIBA Console TOSHIBA Console The TOSHIBA Console provides quick access to computer functions and allows you to customize a range of computer settings. To access the control panel: Click Start, then click All Programs. Point to TOSHIBA Console, then click the resulting Toshiba Console selection.
Page 141: Customizing Your Computer
The hotkey utility allows you to receive a confirmation message when you use the hotkey combination for Standby ] and Hibernation [ Fn+F3 To activate: Click Start, All Programs, Toshiba, Utilities, then click the Hotkey utility. The Toshiba Hotkey window appears. Toshiba Utilities TOSHIBA Console...
Page 142: Toshiba Hw Setup
Start menu, click Control Panel, then Printers and Other Hardware. Then click the Toshiba HWSetup icon. You can also access it from the TOSHIBA Assist screen by clicking Easy Optimize, and then TOSHIBA HW Setup. Sample TOSHIBA HWSetup window...
Page 143: Setting User Passwords
Setting a password leaves your computer secure so that nobody can access your files. You must enter the password before you can work on your computer. Toshiba supports several types of passwords on your computer: ❖ An instant password — Secures your open programs and files when leaving the computer temporarily.
Page 144: Using An Instant Password
Setting user passwords ❖ A supervisor password — Prohibits unauthorized users from accessing certain functions such as Toshiba Hardware Setup. This is useful if more than one person uses the computer. A single user password supports the instant and power-on password functions.
Page 145: Setting A User Password
Setting a user password To register a password for the power-on password functions: Click Start, All Programs, Toshiba, and then Utilities. Point to TOSHIBA Console, then click the resulting TOSHIBA Console selection. The TOSHIBA Console window appears. On the left side, select Security.
Page 146: Using A Supervisor Password
A supervisor password prevents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, Toshiba strongly recommends that you save your password in a location where you can later access it should you not remember it.
Page 147: Deleting A Supervisor Password
Click OK. Deleting a supervisor password To cancel the power-on password function: Click Start, then click All Programs. Point to TOSHIBA Console, then click the resulting TOSHIBA Console selection. The TOSHIBA Console window appears. On the left side, select Security.
Page 148: Using The Toshiba Touch And Launch Utility
To zoom in, hold down the hold down the Using the TOSHIBA Touch and Launch utility TOSHIBA Touch and Launch is a program that adds features to the TouchPad. For example, by selecting an icon you can: ❖ Open a document ❖...
Page 149 A blue circle within the TOSHIBA Touch and Launch window represents your finger location on the TouchPad. As you move the blue circle over an icon in the TOSHIBA Touch and Launch window, the icon is highlighted or selected. Release your finger from a selected icon to choose the icon's function.
Page 150 Toshiba Utilities Using the TOSHIBA Touch and Launch utility The TOSHIBA Touch and Launch window has the following parts: Back button Sample parts of the TOSHIBA Touch and Launch window A short description of the currently selected corner icon appears below the TOSHIBA Touch and Launch window.
Page 151 Sample TOSHIBA Touch and Launch Settings window In the Corner Assignment section you can change the icons you see at the four corners of the TOSHIBA Touch and Launch window using the drop-down list boxes. The icons are referred to as tables in the TOSHIBA Touch and Launch Settings dialog box.
Page 152 The Option button allows you to define how folders will open, define visual effects and control when to show help. A list of tables appears in the Table section of the TOSHIBA Touch and Launch Settings window. These are the same items (icons) you can choose in the Corner Assignment section of the TOSHIBA Touch and Launch Settings.
Page 153: Chapter 6: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
Page 154 If Something Goes Wrong Problems that are easy to fix Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Select the program you want to close, then click End Task.
Page 155: Problems When You Turn On The Computer
Open Notepad (click Start, point to All Programs, then point to Accessories and click Notepad). Press Ctrl Notepad. Add a paragraph break and type some notes describing what you were doing when you received the message, and how the error can be reproduced. Save the file and refer to it when you contact the software manufacturer.
Page 156: External Diskette Drive
If Something Goes Wrong Problems when you turn on the computer returns you to the problem instead of restarting the system. To clear the condition, press Clearing the condition may get the computer running, but it will not solve a resource conflict. Read both the documentation that came with the conflicting device and “Resolving a hardware conflict”...
Page 157: The Windows Operating System Is Not Working
The Windows computer. If this does not work, refer to accessing the hard disk or the external diskette drive.” on page 156. The Windows working Once you are familiar with the desktop and used to the way the operating system responds to your work routine, you can easily detect if the operating system is not working correctly.
Page 158: Internet Problems
If Something Goes Wrong The Windows The Windows options: ❖ Safe Mode ❖ Safe Mode (with Networking) ❖ Safe Mode (with Command Prompt) ❖ Enable Boot Logging ❖ Enable VGA Mode ❖ Last known good configuration (your most recent settings that worked) ❖...
Page 159: The Windows Xp Operating System Can Help You
Click the problem for which you would like help from the listings, and follow the on-screen instructions. You can connect to Support Online by clicking Support from the menu or by going to pcsupport.toshiba.com. If Something Goes Wrong ® operating system is not working ®...
Page 160: Resolving A Hardware Conflict
If Something Goes Wrong Resolving a hardware conflict Resolving a hardware conflict If you receive an error message telling you there is a device driver conflict or a general hardware problem, try using ® Windows Help and Support to troubleshoot the problem first.
Page 161 as it works. These channels of communication are commonly referred to as system resources. Interrupt Request Channel The channel to the CPU is called an Interrupt Request (IRQ) because it interrupts what the processor is doing and requests some of the processor’s time. Direct Memory Access Similarly, the data required by the device is stored in a specific place or address in memory called the Direct...
Page 162: Fixing A Problem With Device Manager
If Something Goes Wrong Resolving a hardware conflict Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable. Device Manager is a configuration tool for advanced users who understand configuration parameters and the ramifications of changing them.
Page 163 type of device, the drivers installed, and the system resources assigned to the device. To check a device’s properties: Open the Start menu, then click Control Panel. Click Performance and Maintenance, and then Administrative Tools. Double-click Computer Management, and then click Device Manager.
Page 164: Memory Problems
If Something Goes Wrong Resolving a hardware conflict Memory problems Incorrectly connected or faulty memory modules may cause errors that seem to be device-related. It is worthwhile checking for these first: Click Start, then click Turn off computer. Click Turn Off. The operating system shuts down and turns off the computer automatically.
Page 165 Here are some typical problems and how to solve them: The AC power light does not come on when you plug in the AC adapter and power cord/cable. Make sure the AC adapter and power cord/cable are firmly plugged into both the wall outlet and the computer. If the AC power light still does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance.
Page 166: Keyboard Problems
Toshiba Web site at accessories.toshiba.com. Keyboard problems If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itself.
Page 167: Display Problems
Display problems Here are some typical display problems and their solutions: The display is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant password feature by pressing password, press the .
Page 168 If Something Goes Wrong Resolving a hardware conflict The built-in screen flickers. Some flickering is a normal result of the way the screen produces colors. To reduce the amount of flickering, try using fewer colors. To change the number of colors displayed: Point at the desktop and click with the secondary button.
Page 169: Disk Drive Problems
Small bright dots appear on your TFT display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. The small bright dots that appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
Page 170 If Something Goes Wrong Resolving a hardware conflict Right-click the drive you want to check and select Properties from the menu. The drive’s properties box appears. This feature is not available for CD/DVD drives. NOTE Click the Tools tab. Click the Check now button. The Check Disk All Apps box appears.
Page 171: Dvd-Rom Or Multi-Function Drive Problems
Some programs run correctly but others do not. This is probably a configuration problem. If a program does not run properly, refer to its documentation and check that the hardware configuration meets its needs. A diskette will not go into the external diskette drive. You may already have a diskette in the drive.
Page 172 If Something Goes Wrong Resolving a hardware conflict Examine the disc to see whether it is dirty. If necessary, wipe it with a clean damp cloth dipped in water or a neutral cleaner. Replace the disc in the tray. Make sure it is lying flat, label side uppermost.
Page 173: Sound System Problems
Sound system problems You do not hear any sound from the computer. Adjust the volume control. Press If you are using external headphones or speakers, check that they are securely connected to your computer. The computer emits a loud, high-pitched noise. This is feedback between the microphone and the speakers.
Page 174 If Something Goes Wrong Resolving a hardware conflict information, or refer to the documentation that came with the PC Card. Some card manufacturers use special software called enablers to support their cards. Enablers result in nonstandard configurations that can cause problems when installing the PC Card.
Page 175 Click the Device Manager button. Double-click the PCMCIA adapter. Double-click the appropriate PC Card. The operating system displays your PC Card’s Properties dialog box, which contains information about your PC Card configuration and status. The computer stops working (hangs) when you insert a PC Card.
Page 176: Printer Problems
If Something Goes Wrong Resolving a hardware conflict If the card is attached to an external device, check that the connection is secure. Refer to the card’s documentation, which should contain a troubleshooting section. Printer problems This section lists some of the most common printer problems: The printer will not print.
Page 177: Modem Problems
preview mode. This mode lets you see your work exactly as it will print. Contact the software manufacturer for more information. Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack.
Page 178: Develop Good Computing Habits
If Something Goes Wrong Develop good computing habits Develop good computing habits Make sure you are prepared. Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature.
Page 179: If You Need Further Assistance
GO, and then clicking the Detailed Specs link from the menu on the left, or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. If Something Goes Wrong...
Page 180: Contacting Toshiba
If you need further assistance Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. Toshiba’s Technical Support Website For technical support, or to stay current on the most recent...
Page 181: Other Toshiba Internet Web Sites
Other Toshiba Internet Web sites toshiba.com computers.toshiba.com www.toshiba.ca www.toshiba-Europe.com www.toshiba.co.jp/index.htm http://servicio.toshiba.com Toshiba’s worldwide offices Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road North Ryde NSW 2113 Sydney Australia France Toshiba Systèmes (France) S.A. 7, Rue Ampère; B. P. 131 92800 Puteaux Cédex...
Page 182 Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm. Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec.
Page 183: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Volume Mute This hot key enables/disables volume mute on your computer.
Page 184: Instant Password Security
Hot Keys Instant password security Instant password security This hot key blanks the display. When the display re-appears, select your user name and enter the correct password if you have created one. Stand By mode This hot key puts the computer into Stand By mode. A message box is displayed by default to confirm that the computer is going into Stand By mode.
Page 185: Hibernation Mode
Hibernation mode This hot key puts the computer into Hibernation mode. If Hibernation mode is enabled (the default), a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it does not display. Sample Hibernation confirmation box If Hibernation mode is disabled, this hot key will not respond.
Page 186: Display Modes
Hot Keys Display modes Display modes This hot key cycles through the power-on display options. The display modes are: Sample display options window In order to use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.
Page 187: Display Brightness
Display brightness This hot key decreases the screen brightness. This hot key increases the screen brightness. Disabling or enabling the TouchPad This hot key enables/disables the TouchPad. To use the TouchPad, see TouchPad” on page Sample disable and enable TouchPad windows Hot Keys Display brightness “Disabling or enabling the...
Page 188: Keyboard Hot Keys
This hot key turns the Zooming utility to zoom-in. For more information, see Zooming Utility” on page This hot key turns the Zooming utility to zoom-out. For more information, see Zooming Utility” on page “Using the TOSHIBA 147. “Using the TOSHIBA 147.
Page 189: Appendix B: Power Cord/Cable Connectors
Appendix B Power Cord/Cable Connectors The computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved United Kingdom...
Page 190: Toshiba Computer
Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between locations and communication networks.
Page 191: Getting Started
Using ConfigFree™ with your Toshiba Computer Getting Started This section contains information about the ConfigFree main screen, and how to start and set up ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application.
Page 192: Configfree Utilities
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample ConfigFree Launcher ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
Page 193 Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample Connectivity Doctor screen Moving the mouse pointer over a wired or wireless network device icon displays information about the device, such as its IP address, subnet mask, and MAC address. A wireless network device also shows information such as the network SSID and the device’s Wired Equivalent Privacy (WEP) key...
Page 194 Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities If a problem, or potential problem, is detected, a triangle containing an exclamation point appears in the Connectivity Doctor screen and an orange frame describes the relevant location. You can then view a possible cause and solution for the problem by clicking the exclamation point.
Page 195: Search For Wireless Devices
Using ConfigFree™ with your Toshiba Computer Search for Wireless Devices The Search for Wireless Devices utility searches for wireless LAN devices currently used in the neighborhood, and displays information about them on a virtual map. To search for wireless devices: Click the Click Search for Wireless Devices.
Page 196: Profile Settings
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample viewing Wi-Fi devices Click your own computer at the center of the map. Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device.
Page 197 Using ConfigFree™ with your Toshiba Computer ❖ Internet settings — includes LAN settings (proxy server settings) and the address of a home page that opens automatically when Internet Explorer starts. ❖ Devices — lets you enable or disable settings of wired and wireless network devices, infrared devices.
Page 198: Quick Connect
Quick Connect The Quick Connect feature switches the Wireless LAN connection to connect to a Toshiba Wireless Projector. Once the projector utility is installed, launching the Quick Connect utility automatically opens the Wireless Data Projector Application.
Page 199 (DPJ), then click Connect. Launching Quick Connect prevents you from using the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection is broken and re- established later.
Page 200 Quick Connect function was started: ❖ If the Toshiba Wireless Projector utility is closed. ❖ If you select Toshiba Wireless Projector (DPJ) from the ConfigFree tray menu (this disconnects the wireless LAN connection). ❖ If you select a profile from the ConfigFree tray menu or when you disable a wireless device.
Page 201: Using The Automatic Switch
Using ConfigFree™ with your Toshiba Computer Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network configuration you use in your office to the one you use at home.
Page 202: Semi-Automatic Switch Feature
Using ConfigFree™ with your Toshiba Computer Semi-Automatic Switch Feature Semi-Automatic Switch Feature The Semi-Automatic feature alerts you when the computer connects to a Service Set Identifier (SSID) stored in a profile, When the computer connects to the designated SSID, a notification window appears.
Page 203: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms These acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory complementary metal-oxide semiconductor...
Page 204 Glossary DIMM DSTN DVD-ROM digital versatile (or video) disc read-only memory EPROM HTML IEEE LPT1 MIDI PCMCIA direct current direct memory access dual inline memory module disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table...
Page 205 SCSI DDRAM SRAM SVGA Terms These terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 206 Glossary application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. backup — A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged.
Page 207 byte — A sequence of eight bits. A byte is the smallest addressable unit of data. See also bit, gigabyte, kilobyte, megabyte. cache — A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer’s main memory.
Page 208 Glossary controller — A device that controls the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and printers all require controllers. CPU — See central processing unit (CPU). CPU cache — A section of very fast memory residing between the CPU and the computer’s main memory that temporarily stores data and instructions the CPU will need to execute commands and programs.
Page 209 disk — A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as diskettes and hard disks. Compare disc. See also diskette, hard disk. disk drive —...
Page 210 Glossary DVD-ROM (digital versatile [or video] disc read-only memory) — A very high-capacity storage medium that uses laser optics for reading data. Each DVD-ROM can hold as much data as several CD-ROMs. Compare CD-ROM. emulation — A technique in which a device or program imitates another device or program.
Page 211 — The physical components of a computer system. Compare software. Hibernation — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 212 Glossary hot swapping — The ability to add or remove devices from a computer while the computer is running and have the operating system automatically recognize the change. icon — A small image displayed on the screen that represents a function, file, or program.
Page 213 local area network — See LAN. logical drive — A section of a disk that is recognized by the operating system as a separate disk drive. A system’s logical drives may differ from its physical drives. For example, a single hard disk drive may be partitioned into two or more logical drives.
Page 214 Glossary non-interlaced — A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen. Compare interlaced. non-system disk — A disk for storing programs and data that cannot be used to start the computer.
Page 215 pointing device — Any device, such as the TouchPad or a mouse, that enables you to move the cursor on the screen. port — A socket on the computer where you plug in a cable for connection to a network or a peripheral device. processor —...
Page 216 Glossary ROM (read-only memory) — Non-volatile memory that can be read but not written to. By non-volatile, we mean that information in ROM remains whether or not the computer is receiving power. This type of memory is used to store your computer’s BIOS, which is essential instructions the computer reads when you start it up.
Page 217 universal serial bus (USB) — A serial bus that supports a data transfer rate of up to 480 Mbps (480 million bits per second). USB can connect up to 127 peripheral devices through a single all-purpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping, serial.
Page 218: Index
47 conserving power 114 disposal 119 not charging 165 unlocking 115 battery power monitoring 111 BIOS see Toshiba Hardware Setup button power 55 start 123 creating 135 playing an audio 133 playing using Auto-Run 134 problem solving 172...
Page 219 122 major features 122 checking properties 163 disabling a device 162 keyboard 68 mouse 68 TOSHIBA Touch and Launch corrupted/damaged data files missing files/trouble accessing a disk 169 running slow 170 can not insert a diskette 171 can’t read a diskette 171...
Page 220 Index disposal information 27 disposing of used batteries 119 DMA (Direct Memory Access) 161 double-click 63 DVD-ROM or multi-function drive cannot access disc 171 DVD-ROM/multi-function drive drive tray will not open 172 problems 171 energy saving features 106 ergonomics 42 error messages device driver conflict 160 general hardware problem 160...
Page 221 desktop 122 hint 37 Internet Explorer 123 moving to desktop 122 recycle bin 123 safety 36 technical note 37 Industry Canada requirement 4 installation memory module 56 installing memory modules 56 mouse 68 instant passwords, using 144 Internal/External mode 168 Internet bookmarked site not found 159 connecting to 131...
Page 222 171 cannot access DVD-ROM or changing display properties checking device properties 163 compact discs not running computer will not power up 155 contacting Toshiba 179 corrupted/damaged data files multi-function drive 171 correctly 172...
Page 223 Device Manager 162 disabling a device 162 disk drive is slow 170 display is blank 167 DVD-ROM/multi-function drive tray does not eject external display not working external keyboard not working external monitor 167 faulty memory 164 hardware conflict 160 high-pitched noise 173 illegal operation 154 Internet bookmarked site not found 159...
Page 224 124 television adjusting display 68 Toshiba Internet Web sites 181 Toshiba Hardware Setup 142 Toshiba online resources 105 TOSHIBA Touch and Launch 148 disable/enable 152 Toshiba utilities 139 Turn Off restarting from 99 using 101 turning computer on/off 97...
Page 225 Web sites,Toshiba 181 Wi-Fi wireless networking 127 Windows Explorer 83 Windows Media Player 133 Windows Millennium Edition Help 160 Windows Start menu 82 Windows XP Help 159 Help and Support 159 problem solving 157 Windows XP Professional desktop wireless interoperability 7...

This manual is also suitable for:

L15-s104 Satellite l10 Satellite l10-101 Satellite l10-103 Satellite l10-117 Satellite l10-118 ... Show all

Toshiba L15-S1041 User Manual

Chapter 1: Getting Started

Chapter 2: Learning the Basics

Chapter 3: Mobile Computing

Chapter 4: Exploring Your Computer's Features

Chapter 5: Toshiba Utilities

Chapter 6: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cord/Cable Connectors

Appendix C: Using Configfree™ with Your Toshiba Computer

Quick Links

Related Manuals for Toshiba L15-S1041

Summary of Contents for Toshiba L15-S1041