Sealey SG139.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Read the instruction manual
1. SAFETY
Familiarise yourself with the application, limitations and potential hazards peculiar to the coating gun.

WARNING! Disconnect the gun from the air supply before changing accessories, servicing or performing any maintenance.

Maintain the gun in good condition (use an authorised service agent).

Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

Keep the gun clean for best and safest performance.

Ensure that the compressed air system can supply the gun air consumption (10cfm).

Wear approved safety respiratory protection and safety eye goggles.

Remove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.

Locate the gun in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate

ventilation and lighting.
Keep children and unauthorised persons away from the work area.

When not in use, ensure that the air supply is turned off.

Avoid unintentional operation of the gun.

DO NOT point the gun at yourself, other persons or animals.

DO NOT direct air from the air hose at yourself, other persons or animals.

DO NOT carry the gun by the hose, or yank the hose from the air supply.

DO NOT use the gun for any purpose other than that for which it is designed.

DO NOT allow untrained persons to operate the gun.

DO NOT get the gun wet or use in damp or wet locations or in areas where there is condensation.

DO NOT operate the gun if any parts are missing or damaged as this may cause failure and/or personal injury.

When not in use, disconnect the gun from the air supply, clean thoroughly and store safely.

2. INTRODUCTION
The underbody coating gun is used for anti-rust treatment of vehicles and agricultural machines by the application of underbody coating. Fits a
standard body "schutz" canister.
3. SPECIFICATION
Air supply:. . . . . . . . . . . . . . . . . . . . . . . . . 60-90psi
Air Consumption: . . . . . . . . . . . . . . . . . . . . . 10cfm
Connection: . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
4. CONTENTS (PARTS)
Item Part No. Description
1 SG139.V2-01 Suction Tube
2 SG139.V2-02 Nozzle
3 SG139.V2-03 Screw Cap
4 SG139.V2-04 Nozzle
5 SG139.V2-05 Gun Body
6 SG139.V2-06 Trigger Stud
7 SG139.V2-07 Stop Ring
5. OPERATION
5.1. Air Supply (Recommended hook-up procedure is shown in fig.1).
5.1.1. Ensure the gun air valve (trigger) is in the off position before
connecting to the air supply.
5.1.2.  WARNING! Ensure the air supply is clean and does not exceed
90psi while operating the spray gun. Too high an air pressure will
shorten the product life and may be dangerous causing damage or
personal injury.
5.1.3. Drain the air supply tank daily. Water in the air line will ruin the paint finish and damage the spray gun.
5.1.4. Clean air inlet filter weekly.
5.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
5.1.6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
© Jack Sealey Limited
INSTRUCTIONS FOR:
UNDERBODY COATING GUN
MODEL NO:
Wear eye protection Wear respiratory protection
Item Part No. Description
8 SG139.V2-08 Packing
9 SG139.V2-09 Valve Spindle
10 SG139.V2-10 O-Ring
11 SG139.V2-11 Air Valve Spring
12 SG139.V2-12 Packing Screw
13 SG139.V2-13 Air Screw
14 SG139.V2-14 Trigger
Original Language Version
SG139.V2
SG139.V2 Issue: 3(L) - 29/10/15