Advertisement

HBD-TZ215/TZ715
SERVICE MANUAL
Ver. 1.0 2011.08
• HBD-TZ215 is the amplifi er, super audio CD/DVD,
USB, tuner and video section in DAV-TZ215.
• HBD-TZ715 is the amplifi er, super audio CD/DVD,
USB, tuner and video section in DAV-TZ715.
Amplifier Section
POWER OUTPUT (rated):
Front L + Front R
65 W + 65 W (at 3 ohms, 1
kHz, 1% THD)
POWER OUTPUT (reference):
Front L/Front R/Center/
Surround L/Surround R:
100 W (per channel at 3
ohms, 1 kHz)
Subwoofer: 100 W (at 3
ohms, 80 Hz)
Inputs (Analog)
TV (AUDIO IN)
Sensitivity: 450/250 mV
Super Audio CD/DVD System
Laser Diode Properties
Emission Duration:
Continuous
Laser Output: Less than
44.6 W
* This output is the value measurement at a distance
of 200 mm from the objective lens surface on the
Optical Pick-up Block with 7 mm aperture.
Signal format system
Latin American models:
NTSC
Other models:
NTSC/PAL
USB Section
(USB) port:
Maximum current:
500 mA
Tuner Section
System
PLL quartz-locked digital
synthesizer
Tuning range
87.5 MHz - 108.0 MHz (50
kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
9-893-291-01
Sony Corporation
2011H33-1
©
2011.08
Published by Sony Techno Create Corporation
Photo: HBD-TZ715
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Video Section
Outputs
VIDEO: 1 Vp-p 75 ohms
HDMI OUT: Type A (19
pin)
General
Power requirements
Latin American models:
110 V - 240 V AC,
50/60 Hz
Other models:
220 V - 240 V AC,
50/60 Hz
Power consumption
On: 105 W
Standby: 0.2 W*
* Valid when the system is in the following status:
– "DEMO" is set to "OFF."
– [CONTROL FOR HDMI] is set to [OFF].
Dimensions (approx.)
430 mm × 67 mm × 335
mm (w/h/d) incl.
projecting parts
Mass (approx.)
3.6 kg
Supported file format
MP3 (MPEG 1 Audio Layer-3)
File Extension:
mp3
Bitrate:
32 kbps - 320 kbps
Sampling frequencies:
32/44.1/48 kHz
WMA (USB device only)
File Extension:
wma
Bitrate:
48 kbps - 192 kbps
Sampling frequencies:
44.1 kHz
AAC (USB device only)
File Extension:
m4a
Bitrate:
48 kbps - 320 kbps
Sampling frequencies:
44.1 kHz
E Model
HBD-TZ210
CDM85MB-DVBU102
KHM-313CAA
Xvid
File Extension:
avi
Video codec:
Xvid video
Bitrate:
4.854 Mbps (MAX)
Resolution/Frame rate:
720 × 480 / 30 fps
720 × 576 / 25 fps
Audio codec:
MP3
MPEG4
File format:
MP4 File Format
File Extension:
mp4/m4v
Video codec:
MPEG4 Simple Profile
(AVC is not compatible.)
Bitrate:
4 Mbps
Resolution/Frame rate:
720 × 576 / 30 fps
Audio codec:
AAC-LC (HE-AAC is not
compatible.)
DRM:
Not compatible
Design and specifications are subject to change
without notice.
Standby power consumption 0.2 W.
Halogenated flame retardants are not used in the
certain printed wiring boards.
Over 85% power efficiency of amplifier block is
achieved with the full digital amplifier, S-Master.
DVD RECEIVER

Advertisement

Table of Contents
loading

Summary of Contents for Sony HBD-TZ215

  • Page 1 SERVICE MANUAL E Model Ver. 1.0 2011.08 Photo: HBD-TZ715 • HBD-TZ215 is the amplifi er, super audio CD/DVD, USB, tuner and video section in DAV-TZ215. • HBD-TZ715 is the amplifi er, super audio CD/DVD, USB, tuner and video section in DAV-TZ715.
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3: Table Of Contents

    HBD-TZ215/TZ715 SECTION 1 SERVICING NOTES TABLE OF CONTENTS UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. SERVICING NOTES ..........(Caution: Some printed circuit boards may not come printed with...
  • Page 4 fl exible printed circuit board has already been con- HBD-TZ215: Indian model 4-296-217-0[] nected. (Do not remove nor unsolder the solder bridge as long as HBD-TZ215: Middle East & African 4-296-217-1[] the OP unit is kept standalone) models...
  • Page 5 HBD-TZ215/TZ715 DISCHARGE THE CHARGED ELECTRICITY IN CAPACITORS TO PREVENT ELECTRIC SHOCK AS FOLLOWS When disassembling the machine, be sure to discharge the charged electricity in the following capacitors. Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
  • Page 6: Disassembly

    HBD-TZ215/TZ715 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-15. HOW TO BEND WIRE (FLAT TYPE) (Page 17) 2-2. CASE (KZ) (Page 7) 2-3. LOADING PANEL 2-7. BACK PANEL BLOCK 2-8. DVD MECHANISM DECK 2-10.
  • Page 7 HBD-TZ215/TZ715 Note: Follow the disassembly procedure in the numerical order given. 2-2. CASE (KZ) 1 screw (BV3 (3-CR)) 1 four screws (BV3 (3-CR)) 1 screw (BV3 (3-CR)) 1 screw (BV3 (3-CR)) 5 case (KZ)
  • Page 8 HBD-TZ215/TZ715 2-3. LOADING PANEL BLOCK 3 two claws 4 loading panel block 1 Insert a screwdriver from between the front panel and the chassis and slide the rod in the direction of the arrow A. tray – Bottom view –...
  • Page 9 HBD-TZ215/TZ715 2-5. FL BOARD, USB KEY BOARD, KZ-USB BOARD 7 connector (CN2101) FL board 6 Lift up two lead pins. 32 ± 1 mm 3 FL board 2 screw (BV3 (3-CR)) 4 three claws 5 USB KEY board 2 screw...
  • Page 10: Key-Sw Board, P-Sw Board

    HBD-TZ215/TZ715 2-6. KEY-SW BOARD, P-SW BOARD Wire (flat type) (11 core) setting 1 connector KEY-SW board P-SW board – Inner view – (CN5301) 2 connector (CN5201) 3 connector (CN5202) 4 five screws (BTP 2 5 eight claws 8 KEY-SW board...
  • Page 11: Back Panel Block

    HBD-TZ215/TZ715 2-7. BACK PANEL BLOCK 7 back panel block 6 two screws (BV3 (3-CR)) 5 screw 6 three screws 4 wire (flat type) (9 core) (BV3 (3-CR)) (CN400) Power cord 2 Remove the power cord from the ditch. 1 power cord connector...
  • Page 12: Dvd Mechanism Deck (Cdm85Mb-Dvbu102)

    HBD-TZ215/TZ715 2-8. DVD MECHANISM DECK (CDM85MB-DVBU102) Note 1: Before disconnecting the wire (fl at type) (24 core) of optical pick-up block, solder the short-land. 3 three screws 7 DVD mechanism deck (BV3 (3-CR)) (CDM85MB-DVBU102) 6 wire (flat type) (24 core)
  • Page 13: Main Board

    HBD-TZ215/TZ715 2-9. MAIN BOARD 8 four screws (BV3 (3-CR)) 9 heat sink block qa two screws 0 holder (IC) (BV3 (3-CR)) 3 Lift up two lead pins. Note: When the heat sink has been removed, apply oil compound (G-747) to it.
  • Page 14: Power Board

    HBD-TZ215/TZ715 2-10. POWER BOARD 5 screw (BV3 (3-CR)) 7 plate flow control (AMP) 1 power cord connector 8 four screws (CN901) (BV3 (3-CR)) 8 four screws (BV3 (3-CR)) 0 POWER board POWER board 4 connector 6 two claws (CN906) 3 connector...
  • Page 15: Ffc Holder

    HBD-TZ215/TZ715 2-11. FFC HOLDER 4 FFC holder block 7 FFC holder Note: Remove the FFC holder from the original set and install it again. 5 two claws 3 wire (flat type) (24 core) 1 two claws 6 wire (flat type) (24 core) 1 two claws –...
  • Page 16: Optical Pick-Up (Khm-313Caa)

    HBD-TZ215/TZ715 2-12. OPTICAL PICK-UP (KHM-313CAA) 1 two insulator screws 3 insulator 5 optical pick-up (KHM-313CAA) 1 two insulator screws 3 insulator 3 insulator 3 insulator 4 connector 2 loading assy (M) – DVD mechanism deck bottom view – 2-13. BELT...
  • Page 17: Dc Motor (Loading) (M001), Ms-203 Board

    HBD-TZ215/TZ715 2-14. DC MOTOR (LOADING) (M001), MS-203 BOARD 4 two solders 6 MS-203 board black 5 DC motor (loading) (M001) 2 three claws 1 screw (M1.7 2.5) 2-15. HOW TO BEND WIRE (FLAT TYPE) : Mountain fold : Valley fold...
  • Page 18: Test Mode

    HBD-TZ215/TZ715 SECTION 3 TEST MODE 2. FL pattern test mode Note: Incorrect operations may be performed if the test mode is not This mode can confi rm the pattern of fl uorescent indicator tube. entered properly. In this case, press the [?/1] button to turn the power off, and Procedure: retry to enter the test mode.
  • Page 19 HBD-TZ215/TZ715 DVD VERSION DISPLAY During the protection state: The STR and DVD microprocessor versions are displayed. 1. If the AC plug is connected or disconnected during the protec- tion state, the protection state is released, and the normal op- Procedure: eration is established.
  • Page 20 HBD-TZ215/TZ715 1. Executing IOP measurement Convert each data from hexadecimal to decimal using conver- sion table. In order to execute IOP measurement, the following standard pro- Please fi nd the label on the rear of the BU (Base Unit). cedures must be followed.
  • Page 21: Electrical Checks

    HBD-TZ215/TZ715 SECTION 4 ELECTRICAL CHECKS The meaning of error code is as below: 2-3. Clear the initialize setup data DVD SECTION Communication error (No reply from syscon) Press [DVD MENU] button and then press [CLEAR] button on the When the optical pick-up assy is replaced, perform the “1. Execut- Syscon hung up remote commander.
  • Page 22: Diagrams

    HBD-TZ215/TZ715 SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - SERVO Section - DVD DRIVE CN1105 RFMON DVDRFIP V2REFO 27 V2REFO (SERVICE JIG) VOA/A DVDA VOB/B DETECTOR DVDB VOC/C DVDC VOD/D DVDD VOE/E+G VOF/F+H A/D CONVERTER IC404 MC_DATA (ADIN) 206 DOUT L-IN...
  • Page 23: Block Diagram - Video Section

    HBD-TZ215/TZ715 5-2. BLOCK DIAGRAM - VIDEO Section - SYSTEM CONTROL IC503 (1/4) V_SEL0 CEC_TX_OUT J400(1/2) CVBS OUT 2 VIDEO OUT VIDEO BUFFER IC400 CN1701 TX2P 1 TMDS DATA2 + TX2N 3 TMDS DATA2 – TX1P 4 TMDS DATA1 + TX1N 6 TMDS DATA1 –...
  • Page 24: Block Diagram - Audio Section

    HBD-TZ215/TZ715 5-3. BLOCK DIAGRAM - AUDIO Section - AUDIO SELECT J400(2/2) IC401 L-CH (Page 22) SYSTEM CONTROL AUDIO IC503 (2/4) R-CH R-CH R-CH Q400 ASEL0 A 10 TUNED TUNED ST_DI/MIC_DATA ST_DO ST_CLK/MIC_CLK ST_CE XSYSRST XSYSRST DVD_RST IFSCK IFCK DVD_SCO IFSDO...
  • Page 25: Block Diagram - Amp Section

    HBD-TZ215/TZ715 5-4. BLOCK DIAGRAM - AMP Section - S-MASTER PROCESSOR IC3001 AMP_D1 AMP_D3 DATA AMP_D2 MCK0 AMP_D3 36 XFSIIN BCK0 BCKO 30 BCK LRCK0 DIGITAL POWER AMP 29 LRCK LRCKO (Page 22) IC3000 MCKO 25 OVF FLAGL TB3001 OVF2 24 OVF FLAGR...
  • Page 26: Block Diagram - Power Section

    HBD-TZ215/TZ715 5-5. BLOCK DIAGRAM - POWER Section - SYSTEM CONTROL DC/DC IC503 (4/4) CONVERTER TRANSFORMER D5000 T5000 FL DISPLAY (AC IN) F901 DRIVER MAIN FILTER S5202,5203 IC5001 TRANSFORMER D901 LF901,902 D931 T901 FUNCTION 94 KEY2 PVDD (+26V) (DIGITAL AMP) SWITCHING...
  • Page 27 HBD-TZ215/TZ715 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Waveforms (In addition to this, the necessary note is printed in each block.) – MAIN Board – For Printed Wiring Boards. For Schematic Diagrams. Note: Note: IC1101 0 (DVDRFIP) IC400 4 (IN2) •...
  • Page 28: Printed Wiring Board - Main Section (1/2)

    HBD-TZ215/TZ715 5-6. PRINTED WIRING BOARD - MAIN Section (1/2) - • See page 27 for Circuit Boards Location. • : Uses unleaded solder. MAIN BOARD (SIDE A) CN1701 HDMI OUT (CHASSIS) (CHASSIS) (CHASSIS) (TO WRITE JIG) IC1707 CN508 C1729 IC1110...
  • Page 29: Printed Wiring Boards - Main Section (2/2)

    HBD-TZ215/TZ715 5-7. PRINTED WIRING BOARDS - MAIN Section (2/2) - • See page 27 for Circuit Boards Location. • : Uses unleaded solder. TB3001 TV AUDIO SPEAKERS VIDEO FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER MAIN BOARD (SIDE B)
  • Page 30: Schematic Diagram - Main Section (1/8)

    HBD-TZ215/TZ715 5-8. SCHEMATIC DIAGRAM - MAIN Section (1/8) - • See page 44 for IC Block Diagrams. (1/8) MAIN BOARD IC1110 IC1110 MM1961JTRE +1.8V REG. MAIN RF+3.3V BOARD D3.3V (4/8) (Page 33) D-GND C1187 C1198 C1183 R2178 CN1101 0.33 JL2101...
  • Page 31: Schematic Diagram - Main Section (2/8)

    HBD-TZ215/TZ715 5-9. SCHEMATIC DIAGRAM - MAIN Section (2/8) - • See page 28 for waveforms. • See page 49 for IC Pin Function Description. (Page 34) MAIN BOARD (2/8) MAIN BOARD BUS3 (5/8) MAIN MAIN (Page 34) BOARD BUS2 BOARD...
  • Page 32: Schematic Diagram - Main Section (3/8)

    HBD-TZ215/TZ715 5-10. SCHEMATIC DIAGRAM - MAIN Section (3/8) - • See page 44 for IC Block Diagrams. (3/8) MAIN BOARD R9942 R9946 E3.3V R9941 Q9730 INK0001AC1-T112-1 LEVEL SHIFT D9712 R9945 DA2J10100L MAIN (Page 35) BOARD (6/8) CEC_TX_OUT CN1701 HDMI OUT...
  • Page 33: Schematic Diagram - Main Section (4/8)

    HBD-TZ215/TZ715 5-11. SCHEMATIC DIAGRAM - MAIN Section (4/8) - • See page 44 for IC Block Diagrams. MAIN BOARD (4/8) D3.3V C1516 1000p MAIN (Page 30) VREFO D-GND BOARD (1/8) REG01 RF+3.3V MAIN IC B/D IC1501 R1527 (Page 30) FCS+...
  • Page 34: Schematic Diagram - Main Section (5/8)

    HBD-TZ215/TZ715 5-12. SCHEMATIC DIAGRAM - MAIN Section (5/8) - • See page 28 for waveforms. • See page 44 for IC Block Diagrams. • See page 49 for IC Pin Function Description. MAIN BOARD (5/8) MAIN (Page 31) BUS3 BOARD...
  • Page 35: Schematic Diagram - Main Section (6/8)

    HBD-TZ215/TZ715 5-13. SCHEMATIC DIAGRAM - MAIN Section (6/8) - • See page 44 for IC Block Diagrams. MAIN BOARD (6/8) MAIN (Page 31) BUS2 BOARD (2/8) IC471 IC471 TC74LCX541FT(EKJ) C471 BUS BUFFER C476 0.01 R480 AMP_D1 R412 R481 0 <1.2>...
  • Page 36: Schematic Diagram - Main Section (7/8)

    HBD-TZ215/TZ715 5-14. SCHEMATIC DIAGRAM - MAIN Section (7/8) - • See page 44 for IC Block Diagrams. MAIN BOARD (7/8) FRONT R CL3023 CL3024 FRONT L CL3025 CL3026 C3089 C3088 TB3001 0.01 0.01 SUR R CL3021 SPEAKERS CL3020 SUR L...
  • Page 37: Schematic Diagram - Main Section (8/8)

    HBD-TZ215/TZ715 5-15. SCHEMATIC DIAGRAM - MAIN Section (8/8) - • See page 28 for waveforms. • See page 44 for IC Block Diagrams. (8/8) MAIN BOARD C3109 R3094 R3098 R3099 R3111 R3112 C3121 R3105 100k 100k 100k 100k 100k 100k 13.1...
  • Page 38: Printed Wiring Board - Fl Board

    HBD-TZ215/TZ715 5-16. PRINTED WIRING BOARD - FL Board - • See page 27 for Circuit Boards Location. • : Uses unleaded solder. FL BOARD 51 52 CL5051 JW5014 CL5021 CL5007 CL5039 CL5014 CL5005 IC5002 CL5042 CL5003 CL5006 CL5009 CL5004 CL5038...
  • Page 39: Schematic Diagram - Fl Board

    HBD-TZ215/TZ715 5-17. SCHEMATIC DIAGRAM - FL Board - • See page 44 for IC Block Diagrams. FL BOARD ND5000 FLUORESCENT INDICATOR TUBE T5000 -27.8 IC5002 DC/DC CONVERTER TRANSFORMER IC5002 PNA4823M02S0 D5000 C5010 REMOTE MC2840 C5004 C5005 CONTROL 4700p 0.022 RECEIVER...
  • Page 40: Printed Wiring Boards - Key Section

    HBD-TZ215/TZ715 5-18. PRINTED WIRING BOARDS - KEY Section - • See page 27 for Circuit Boards Location. • : Uses unleaded solder. (Page 29) (Page 38) MAIN BOARD BOARD CN5006 CN2101 USB KEY BOARD KZ-USB BOARD S5114 REC TO USB...
  • Page 41: Schematic Diagram - Key Section

    HBD-TZ215/TZ715 5-19. SCHEMATIC DIAGRAM - KEY Section - KZ-USB BOARD ET5001 USB KEY BOARD CL5110 S5113 (CHASSIS) ROTARY ENCODER CL5200 MASTER VOLUME CL5205 R5125 CN5201 CL5107 CL5201 VBUS CL5109 CN5200 CL5202 MAIN CL5203 C5200 R5126 BOARD R5127 R5128 R5129 CL5204 4.7k...
  • Page 42: Printed Wiring Board - Power Board

    HBD-TZ215/TZ715 5-20. PRINTED WIRING BOARD - POWER Board - • See page 27 for Circuit Boards Location. • : Uses unleaded solder. POWER BOARD (CHASSIS) CL005 CL009 JW939 CL056 C924 CL052 R908 CL004 CL051 D907 C903 JW945 D910 C918 CL053...
  • Page 43: Schematic Diagram - Power Board

    HBD-TZ215/TZ715 5-21. SCHEMATIC DIAGRAM - POWER Board - • See page 44 for IC Block Diagrams. CL020 CL011 CL010 EB908 POWER BOARD (CHASSIS) F901 C963 C964 CN901 T5AH 250V (TZ215: E3, E12/TZ715) 470p 470p D901 C920 T6.3AH 250V (TZ215: E32)
  • Page 44 HBD-TZ215/TZ715 • IC Block Diagrams IC507 MM1665AHBE IC509 SI-3010KM-TLS IC510 MM1663DHBE – MAIN Board – IC307 TC7WH157FK IC400 MM1508XNRE 8 7 6 5 6 IN1 THERMAL 11 7 BIAS SHUTDOWN 11 6 SELECT 4 IN2 EN G DRIVER – DRIVER...
  • Page 45 HBD-TZ215/TZ715 IC1105, 1107 MM3404A33URE IC3006 MM3404A18URE CE 1 BIAS VOLTAGE – REFERENCE CURRENT LIMIT VOUT GND 2 IC3000, 3002, 3004 CXD9965TN GVDD_B GVDD_A UNDER /OTW VOLTAGE 43 BST_A PROTECTION INTERNAL PULLUP 42 NC RESISTORS TO VREG POWER VREG PROTECTION PVDD_A...
  • Page 46 HBD-TZ215/TZ715 IC1707 RP173N501B-TR-FE IC1708 RP173N331B-TR-FE 5 VOUT CURRENT REVERSE VREF LIMIT DETECTOR 4 NC IC3001, 3003, 3005 CXD9788AR CLOCK CLOCK GENERATOR GENERATOR 36 XFSIIN (SECONDARY) (PRIMARY) XVSS 35 DVDD VSUBC 34 TEST 33 BFVSS VSSR OUTR2 32 BFVDD VDDR DATA FILTER &...
  • Page 47 HBD-TZ215/TZ715 – FL Board – IC5000 MM3404A33URE CE 1 BIAS VOLTAGE – REFERENCE CURRENT LIMIT VOUT GND 2 IC5001 HT16515 LED0 LED1 4-BIT LATCH LED2 LED3 GRID 12-BIT SHIFT DRIVER REGISTER KEY DATA MEMORY 33 SEG19/GRID10 (2 x 16) 32 SEG18/GRID11...
  • Page 48 HBD-TZ215/TZ715 – POWER Board – IC901 STR-F6168-LF1352 CURRENT MIRROR DELAY LATCH DELAY OVER BOTTOM CURRENT PROTECT SKIP LOGIC LOGIC OVER OVER OVER VOLTAGE THERMAL OVER LOAD CURRENT FEED CURRENT PROTECT SHUT DOWN PROTECT PROTECT BACK PROTECT INTERNAL BIAS SWITCHING UNDER VOLTAGE...
  • Page 49 HBD-TZ215/TZ715 • IC Pin Function Description MAIN BOARD IC1101 CXD9927R-B (CD/DVD RF AMP, FOCUS/TRACKING ERROR AMP, DVD SYSTEM CONTROL, DSP, DIR/USB/HDMI CONTROL) Pin No. Pin Name Description — RF offset cancellation capacitor connecting terminal RFGC RF AGC loop capacitor connecting terminal...
  • Page 50 HBD-TZ215/TZ715 Pin No. Pin Name Description 63, 64 HA18, HA19 Flash ROM address bus A18, A19 output DVDD3 — Power supply (+3.3V) Flash ROM write signal output 67 to 74 HA16 to HA9 Flash ROM address bus A16 to A9 output...
  • Page 51 HBD-TZ215/TZ715 Pin No. Pin Name Description REGRST REG reset signal output for Focus/Tracking/Sledding motor driver MUTE Mute signal output for Spindle motor DDC_DA HDMI DDC line data input/output DVDD18 — Power supply (+1.8V) DDC_CLK HDMI DDC line clock input/output HTPLG...
  • Page 52 HBD-TZ215/TZ715 Pin No. Pin Name Description APLLVSS — Ground ADACVSS2 — Ground ADACVSS1 — Ground DIR_CE — Not used. (Open) ASDATA3 — Not used. (Open) ASDATA2 Audio digital signal output to D-AMP AVCM — Ext capacitor connected terminal ASDATA1 Audio digital signal output to D-AMP...
  • Page 53 HBD-TZ215/TZ715 MAIN BOARD IC503 R5F364AEDFA (SYSTEM CONTROL) Pin No. Pin Name Description DAMP_SCDT/DIR_DIN DAMP processor data output DAMP_SHIFT/ DAMP processor clock output DIR_CLK FL_STB FL driver chip select signal output SIRCS_IN Sircs signal input FL_DATA/LED_DATA FL and LED driver data output...
  • Page 54 HBD-TZ215/TZ715 Pin No. Pin Name Description DAMP INIT D-AMP processor reset signal output SOFT_MUTE D-AMP processor soft muting signal output DAMP_LATCH1 D-AMP processor latch-1 (Front L/R) signal output DAMP_LATCH2 D-AMP processor latch-2 (Surround L/R) signal output DAMP_LATCH3 D-AMP processor latch-3 (Center/Subwoofer) signal output —...
  • Page 55: Exploded Views

    HBD-TZ215/TZ715 SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • Color Indication of Appearance Parts Ex- The components identifi ed by mark 0 they may have some difference from the ample: or dotted line with mark 0 are critical for original one.
  • Page 56: Front Panel Section

    HBD-TZ215/TZ715 6-2. FRONT PANEL SECTION not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-296-216-01 ESCUTCHEON (KZ-A) (TZ215) 4-161-827-01 WINDOW (KZ) 4-296-216-11 ESCUTCHEON (KZ-A) (TZ715) 4-161-828-01 BASE, FRONT (KZ)
  • Page 57: Front Boards Section

    HBD-TZ215/TZ715 6-3. FRONT BOARDS SECTION (E32) not supplied TU401 chassis section not supplied not supplied not supplied not supplied (KZ-USB board) Note: If the wire (fl at type) was replaced, refer to “2-15. HOW TO BEND WIRE (FLAT TYPE)” on the page 17.
  • Page 58: Chassis Section

    HBD-TZ215/TZ715 6-4. CHASSIS SECTION not supplied not supplied (TZ215: E32) not supplied not supplied DVD mechanism deck section (CDM85MB-DVBU102) F901 not supplied not supplied supplied not supplied not supplied not supplied Note: If the wire (fl at type) was replaced, refer to “2-15. HOW TO BEND WIRE (FLAT TYPE)”...
  • Page 59: Dvd Mechanism Deck Section (Cdm85Mb-Dvbu102)

    HBD-TZ215/TZ715 6-5. DVD MECHANISM DECK SECTION (CDM85MB-DVBU102) not supplied not supplied not supplied MS-203 board loading motor (M001) not supplied (E12) not supplied supplied Note: If the wire (fl at type) was replaced, refer to “2-15. HOW TO BEND WIRE (FLAT TYPE)” on the page 17.
  • Page 60: Electrical Parts List

    HBD-TZ215/TZ715 SECTION 7 KEY-SW ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- the parts list may be different from the uF: μF ber, please include the board name. parts specifi ed in the diagrams or the com- •...
  • Page 61 HBD-TZ215/TZ715 KEY-SW KZ-USB MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S5204 1-786-650-21 SWITCH, TACTILE (FUNCTION) C514 1-107-826-11 CERAMIC CHIP 0.1uF ************************************************************ C515 1-107-826-11 CERAMIC CHIP 0.1uF KZ-USB BOARD C516 1-165-908-11 CERAMIC CHIP 1uF ************...
  • Page 62 HBD-TZ215/TZ715 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1135 1-164-677-11 CERAMIC CHIP 0.033uF C1516 1-162-964-11 CERAMIC CHIP 0.001uF C1136 1-162-970-11 CERAMIC CHIP 0.01uF C1518 1-107-826-11 CERAMIC CHIP 0.1uF C1137 1-107-826-11 CERAMIC CHIP 0.1uF C1520...
  • Page 63 HBD-TZ215/TZ715 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3036 1-107-826-11 CERAMIC CHIP 0.1uF C3110 1-112-246-11 ELECT 100uF C3037 1-107-826-11 CERAMIC CHIP 0.1uF C3111 1-107-826-11 CERAMIC CHIP 0.1uF C3038 1-107-826-11 CERAMIC CHIP 0.1uF C3112 1-115-339-11 CERAMIC CHIP 0.1uF...
  • Page 64 HBD-TZ215/TZ715 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D2101 6-503-018-01 DIODE DZ2J08200L IC3003 6-705-979-01 IC CXD9788AR D2102 6-501-592-01 DIODE EDZCTE616.8B IC3004 6-713-634-01 IC CXD9965TN IC3005 6-705-979-01 IC CXD9788AR D2103 6-501-592-01 DIODE EDZCTE616.8B D4002 6-502-961-01...
  • Page 65 HBD-TZ215/TZ715 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R415 1-216-837-11 METAL CHIP 1/10W R609 1-216-833-11 METAL CHIP 1/10W R416 1-216-845-11 METAL CHIP 100K 1/10W R614 1-216-809-11 METAL CHIP 1/10W R615 1-216-821-11 METAL CHIP 1/10W...
  • Page 66 HBD-TZ215/TZ715 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1536 1-218-863-11 METAL CHIP 4.7K 0.5% 1/10W R3029 1-216-864-11 SHORT CHIP R1537 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W R3030 1-216-845-11 METAL CHIP 100K 1/10W R1538 1-218-863-11 METAL CHIP 4.7K...
  • Page 67 HBD-TZ215/TZ715 MAIN MS-203 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R3100 1-216-837-11 METAL CHIP 1/10W MS-203 BOARD R3101 1-216-833-11 METAL CHIP 1/10W ************ R3102 1-216-817-11 METAL CHIP 1/10W < CONNECTOR > R3103 1-216-805-11 METAL CHIP...
  • Page 68 HBD-TZ215/TZ715 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C973 1-114-325-11 CERAMIC CHIP 0.1uF < COIL > C975 1-114-325-11 CERAMIC CHIP 0.1uF C976 1-126-933-11 ELECT 100uF L931 1-457-878-65 INDUCTOR 2.2uH 0 C981 1-162-968-11 CERAMIC CHIP 0.0047uF...
  • Page 69 HBD-TZ215/TZ715 POWER P-SW USB-KEY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R946 1-216-827-11 METAL CHIP 3.3K 1/10W R5127 1-216-829-11 METAL CHIP 4.7K 1/10W R949 1-216-827-11 METAL CHIP 3.3K 1/10W R5128 1-216-829-11 METAL CHIP 4.7K 1/10W...
  • Page 70 HBD-TZ215/TZ715 REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2011.08...

This manual is also suitable for:

Hbd-tz715

Table of Contents