Sealey BT102.V2 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. safety
▲ danger! Be AWAre, leAd-Acid BAtteries GenerAte eXPlosiVe GAses durinG normAl BAtterY oPerAtion. for
tHis reAson, it is VerY imPortAnt to reAd And folloW tHese instructions cArefullY, eAcH time You use tHe
BAtterY tester.
follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend
to use in the vicinity of the battery. remember to review warning marks on all products and on engines.
1.1. Personal PreCaUtions
ensure that there is another person within hearing range and close enough to come to your aid, should a problem arise when working
9
near a lead-acid battery.
Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.
9
Have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
9
Wash immediately with soap and water if battery acid contacts skin or clothing. if acid enters eye, flush eye immediately with cool, clean
9
running water for at least 15 minutes and seek immediate medical attention.
remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current
9
which is high enough to weld such items to the vehicle and cause severe burns.
ensure that hands, clothing are clear of fan blades and other moving or hot parts of engine. remove ties and contain long hair.
9
do not smoke or allow a spark or flame in the vicinity of the battery or engine.
8
1.2. general safety instrUCtions
familiarise yourself with the application, limitations and potential hazards of the tester. Also refer to the vehicle manufacturer's hand
9
book. if in AnY douBt consult A QuAlified electriciAn.
ensure that the tester is in good condition before use. if in any doubt do not use the unit and contact a qualified electrician.
9
only use recommended attachments and parts. to use unapproved items may be dangerous and will invalidate your warranty.
9
Keep tools and other items away from the engine and ensure that you can see the battery and working parts of engine clear.
9
determine the system voltage before using the tester.
9
if the tester receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
if the battery terminals are corroded or dirty, clean them before using the tester.
9
Keep children and unauthorised persons away from the work area.
9
do not disassemble the tester for any reason. the tester must only be checked by qualified service personnel.
8
Warning! to prevent the risk of sparking, short circuit and possible explosion do not drop metal tools in the battery area, or allow
‰
them to touch the battery terminals.
do not cross-connect tester to battery. ensure positive (red) clamp is to positive terminal and negative (BlAcK) clamp is to negative
8
terminal.
do not use the tester outdoors, or in damp, or wet locations and do not use in the vicinity of flammable liquids or gases.
8
ensure there is effective ventilation to prevent a build-up of explosive gases.
9
do not use the tester for a task for which it is not designed.
8
When not in use, store the tester carefully in a safe, dry, childproof location.
9
2. introdUCtion
compact design digital tester suitable for professional use. utilises low current draw technology to evaluate condition of sli, VrlA, AGm and
Gel batteries and charging systems. Just key in the battery rating from the top of the battery. simple, fast and accurate evaluation of battery
condition. results displayed on led control panel. no internal battery and will test batteries with a residual charge of just 7V. can also be used
to evaluate the condition of the alternator and charging circuitry of the vehicle.
3. sPeCifiCation
model no ....................................................................................Bt102.V2
rated Battery Voltage ............12V Battery 12V charging/starting systems
rating systems .....................................................sAe, din, en, iec, cA
test range..................................................200-1200 ccA* (sAe), 7-15V
minimum Power requirement...............................................................7V
note...............................................................*ccA - cold cranking Amps
© Jack sealey limited
instructions for
digital battery & alternator
tester 12V
model no:
Warning
Wear protective
gloves
corrosive
substance
Original Language Version
bt102.V2
Warning: Keep away
from sources of
explosive
ignition
material
use in well Keep in dry area
ventilated areas protect from rain
Bt102.V2 | issue 1 24/01/17