Sealey wpd133a Quick Start Manual

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
instruction
manual
1. SaFety
electrical SaFety
1.1.
warninG! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information: it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
do not pull or carry the appliance by the power cable.
8
do not pull the plug from the socket by the cable.
8
do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.1.5. only allow the minimal amount of pump cable to enter water or wet areas. the electrical cable is designed
for use in water and must not be substituted. if damaged contact a qualified electrician.
1.1.6. extension cable use. only use a cable designed for use with water equipment. contact your dealer or a qualified electrician
for advice. ensure water is kept clear of electrical mains power supply. do not touch switch or plug with wet hands.
1.1.7. only allow the minimal amount of pump cable to enter water or wet areas. the electrical cable is designed for use in water and must
not be substituted. if damaged contact a qualified electrician.
1.1.8. extension cable use. only use a cable designed for use with water equipment. contact your dealer or a qualified electrician
for advice. ensure water is kept clear of electrical mains power supply. do not touch switch or plug with wet hands.
1.2. General SaFety
warninG! Pump must be used in accordance with Health & safety, government, local authority, and water authority rules and
‰
regulations.
familiarise yourself with application and limitations, as well as the specific potential hazards peculiar to the pump.
9
warninG! disconnect the pump from the mains power before changing accessories, servicing or performing any maintenance.
‰
maintain the pump in good condition (use an authorised service agent). Keep the pump clean.
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
if pump is used to pump water from a well, drain or deep receptacle, take adequate precautions to stop persons or animals from
9
falling in.
use the moulded handle to lower or raise the pump. it may be necessary to attach a suitable rope or pulley to the handle.
9
if the bottom of the water container is covered with sludge, sand, gravel or mud etc, suspend the pump or place it on a raised base to
9
operate above the solid matter. this is not essential but will increase the efficiency and longevity of the pump.
in flood situations, the user is responsible for ensuring that appropriate back-up procedures, alarms etc are correctly installed in case of
9
pump failure.
in swimming pools, fish ponds, etc, ensure location is clear of people and animals, including removal of fish from pond.
9
note: this pump is not designed for continuous use in a fish pond or similar water feature or display, see section 4 "operating
instructions".
do not operate the pump if any parts are damaged or missing as this may cause failure and/or possible personal injury.
8
© Jack sealey limited
instructions for
SubmerSible dirty water pump
automatic 133ltr/min 230v
wpd133a
model no:
Original Language Version
replacement fuse
5 amp
rating:
WPD133A Issue 2 (H, F) 02/01/18