Sealey TP6908 Quick Start Manual

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SaFEty
WarninG! ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this
‰
equipment.
Familiarise yourself with the extractors application and limitations, as well as the specific potential hazards peculiar to this product.
9
Maintain the extractor in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. non authorised parts will invalidate the warranty.
9
Use only to extract engine or transmission oils, or similar non-Corrosive fluids. Unit may also be used for the transfer of water.
9
ensure safety eye protection and protective clothing are worn when using this product.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Maintain correct balance and footing. ensure the floor is not slippery and wear non slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
dispose of waste liquids in accordance with local authority regulations.
9
dO nOt store fluids in the TP6908 container. once used to extract fluid, it must be emptied into an approved receptacle as soon as
8
possible.
dO nOt over tip the extractor when emptying as this may cause fluid to enter the inner pump chamber. See fig.1
8
dO nOt use to extract hazardous or harmful chemicals, solvents, petrol, diesel, kerosene, alkaline
8
or acids. If by chance such fluids are used in the unit, it must be immediately drained and thoroughly
cleaned. Use with prohibited fluids will invalidate your warranty.
dO nOt dismantle, tamper or adapt the extractor for any purpose other than for which it is designed.
8
dO nOt use the unit if it has been dropped or mishandled, check the unit to ensure there is no
8
damage.
Keep the extractor clean and store in a safe dry location. dO nOt store in areas of high temperature, direct
9
sunlight, rain or snow.
2. intrOductiOn
18ltr Capacity device constructed from composite materials. largest capacity manual extractor on the market.
Uses manual pump to generate vacuum. Suitable for the extraction of all types of engine, transmission and
lubricating oil from cars, motorcycles, marine engines, stationary engines and industrial machinery. Also
suitable for low viscosity fluids such as water. Supplied with Ø5.8 and Ø6.7mm suction probes and Ø9.8mm
extension tube. Uses probes to extract engine oil through the dipstick tube. Unit can be tipped passed 90° for
easier emptying. Fitted with three castor wheels enabling easy manoeuvrability when the unit is full.
3. SPEciFicatiOn
Model no: ..................................................................TP6908
Capacity: ......................................................................... 18ltr
extension Tube: ....................................................... Ø9.8mm
Suction Probes: ...............................................Ø5.8, Ø6.7mm
4. OPEratiOn
4.1. Oil ExtractiOn
4.1.1. Ensure the vehicle is on level ground and run the engine for approximately 5 minutes to warm the oil
and allow any contaminants within the oil to thoroughly mix and turn the engine off.
4.1.2. Remove the vehicle's oil dipstick.
4.1.3. Select and insert the appropriate diameter probe (fig.2) into the dipstick hole until it reaches the
bottom of the sump.
4.1.4. Connect the main suction tube (fig.3) to both the pump inlet and required probe (fig.2).
4.1.5. Raise the handle to its highest limit and pump it fully several times to create a vacuum which will
automatically begin to extract the oil/fluid. observe the oil/fluid as it rises up the chamber and
stop pumping when the fluid is 6"(150mmm) from the top. The unit will continue to fill and will
automatically shut off when the internal float valve operates. dO nOt continue to pump after the unit
has shut off as this may result in liquid entering the inner pump chamber. If this should occur refer to
© Jack Sealey limited
Vacuum Oil & Fluid ExtractOr manual
18ltr
Model no:
Wear protective Wear safety
gloves footwear
Original Language Version
tP6908
Wear protective
clothing
TP6908 Issue 1 11/12/18