Replacing The Battery; Unit Conversion Button; Weighing - Silvercrest HG00496A Operation And Safety Notes

battery compartment cover
compartment until you hear it lock into place.
13
5. Tighten the screw by using a scewdriver
(see Fig. B).

Replacing the battery

Q
1. Switch off the kitchen scale
down the On / Off / Zero button
2. Loosen the screw located at the back of the
kitchen scale
by using a screwdriver. Open
2
the battery compartment
3. Remove the exhausted batteries from the battery
embedding case
11
the black battery locking tab
automatically released from the battery embed-
ding case . Ensure that you do not exert too
11
much force on the battery metal contact
otherwise it could be damaged by over-bending
as the battery is lifted. Remove the battery from
the battery embedding case
4. Insert a new battery into the battery embedding
case . Make sure you fit the battery the right
11
way round (polarity). The "+"- side must face
upwards. The battery must be pressed inside
the battery embedding case
5. Close the battery compartment
the screw by using a screwdriver.

Unit conversion button

Q
T he g / lb:oz unit conversion button
units of weight can be found on the bottom of
the kitchen scale
2
button the units of measure change between
metric (g, ml) and imperial (lb:oz, fl'oz).
Note:
– If the units of weight are set to metric (g) then the
units of volume will be automatically shown as ml.
– If the units of weight are set to imperial (lb:oz)
then the units of volume will be automatically
shown as fl'oz.
– The standard unit of weight is g.
20 GB/IE
onto the battery
8
. Press and hold
2
for 3 seconds.
5
as described above.
13
by pressing and pulling
. The battery is
12
,
10
.
11
.
11
and tighten
13
for the
9
. By simply pressing the

Weighing

Q
Note: Starting with or without the weighing bowl
the kitchen scale always starts from 0 g /
2
0:0.0 lb:oz / if the On / Off / Zero button
16 19
is pressed.
If you place the weighing bowl
scale after it has been switched on, then the dis-
2
play will show the weight of the weighing bowl
Press the On / Off / Zero button
display to 0 g / 0:0.0 lb:oz
shows on the LC display
P lace the kitchen scale on a solid, flat surface.
P ress the On / Off / Zero button
on the kitchen scale
W ait until the LC display
on 0 g , 0:0.0 lb:oz
16
, which will be the mode the kitchen scale
18
was in when it was last switched off.
P ress the mode setting button
kitchen scale to the normal weighing mode
I f necessary select the units of weight in ad-
vance by pressing the g / lb:oz unit conversion
button on the bottom of the kitchen scale
9
before you start weighing.
For re-calibrating the kitchen scale
you have selected the units of weight press and
hold down the On / Off / Zero button
seconds to switch off the kitchen scale
S tand the kitchen scale
surface. Place the weighing bowl
weighing platform
P ress the On / Off / Zero button
the kitchen scale in the normal weighing mode.
W ait until all the segments of the LC display
have illuminated and the kitchen scale
stabilized at 0 g
16
P lace the substance to be weighed into the
weighing bowl to start the weighing process.
1
The LC display shows the weight of the sub-
4
stance in the weighing bowl
unit of weight (see Fig. D).
on the kitchen
1
once to reset the
5
/ , "T" (TARE)
16 19
.
4
to switch
5
(see Fig. C).
2
stops and stabilizes
4
or 0 ml or 0.0 fl'oz
19 17
to set the
3
, when
2
for 3
5
.
2
on a hard, flat table
2
on the
1
.
6
to switch on
5
has
2
, 0:0.0 lb:oz .
19
in the selected
1
,
1
5
.
1
25
.
22
4