Sealey MC135 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINgS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAgE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE kEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNINg! Do not use if the lift will foul on the exhaust or other vulnerable

parts. Remove lower fairing or obstructing trims before use and ensure the bike
is adequately strapped onto the lift before operating.
Maintain the lift in good condition (use an authorised service agent).

replace or repair damaged parts. Use genuine parts only. Unauthorised parts may

be dangerous and will invalidate the warranty.
use a qualified person to lubricate and maintain the lift. DO NOT use brake fluid to

top up hydraulic unit.
Locate the lift in a suitable work area, keep area clean and tidy and free from

unrelated materials, and ensure that there is adequate lighting. Also ensure that the
floor is level and strong enough (preferably concrete) to take the weight of the lift
and the bike. DO NOT operate the lift on tarmacadam, as the surface may be
unstable.
Keep the lift clean for best and safest performance.

the maximum bike weight is 135kg. DO NOT exceed this rated capacity.

remove ill fitting clothing. remove ties, rings and other loose jewellery, and contain

long hair.
Maintain correct balance and footing, do not over-reach. Ensure the floor is not

slippery and wear non-slip shoes.
Ensure the bike is adequately secured to the lifting platform.

Before lifting check that there are no overhead obstructions.

When platform has been raised to the working height ensure the platform safety rod

is engaged to prevent accidental lowering.
Keep children and unauthorised persons away from the work area.

the lowering speed will vary according to the weight of the load and the release

valve setting.
DO NOT use the lift for a task it is not designed to perform.

DO NOT operate the lift if damaged.

DO NOT exceed the rated capacity of the lift.

DO NOT operate the lift when you are tired or under the influence of alcohol, drugs

or intoxicating medication.
DO NOT allow untrained persons to operate the lift.

DO NOT make any modifications to the lift and DO NOT adjust or tamper with the

safety valve.
Before lowering the lift ensure that there are no obstructions underneath the

platform and that all persons are standing clear.
Before storing in safe area, ensure all parts are clean and free of grease and oil.

store lift in the lowest position and in a childproof location.

2. SPECIFICATION
All-steel scissor type construction with foot operation and integral hydraulic pump.
unique foot design and safety pins allow use with off-road bikes. features four locking
heights. support platform with rubber top protects paintwork on bike.
Specification
capacity . . . . . . . . . . . . . . . . . . . . . . . 135kg
Minimum height . . . . . . . . . . . . . . . . 355mm
Maximum height . . . . . . . . . . . . . . . . 895mm
3. ASSEMBLY
3.1. Assembly
3.1.1. Insert lift pedal fig.1A into jack socket and secure using bolt fig.1B.
NOTE! Lift shown in raised position for clarity. The pedal should be fitted with the lift in
the lowered position.
3.1.2 fit the anchor point brackets x 2 to the platform as fig.2, ensure that you use
four nuts per bracket, one either side of the platform. choose one of the two
available positions that will best align with the foot pegs of your off-road bike.
3.2. Before first use
3.2.1. Before using the lift, purge the hydraulic circuit, to eliminate any air in the
system, by fully pressing the release valve pedal and pumping the lift pedal 15
to 20 times.
3.2.2. test the lift, unladen, by raising it to full height and then lowering it.
Depress release valve pedal slowly to control the rate of descent.
InstructIons for:
MOTORCYCLE LIFT 135kg
MoDEL no:
Original Language Version
MC135
fig.1
A
fig.2
B
Mc135 Issue: 2 - 15/10/09