Sealey POWER PRODUCTS SA206 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PleASe reAD tHeSe INStruCtIoNS CAreFullY. Note tHe SAFe oPerAtIoNAl reQuIreMeNtS, WArNINgS & CAutIoNS.
uSe tHe ProDuCt CorreCtlY AND WItH CAre For tHe PurPoSe For WHICH It IS INteNDeD. FAIlure to Do So MAY CAuSe
DAMAge AND/or PerSoNAl INJurY AND WIll INVAlIDAte tHe WArrANtY. PleASe KeeP INStruCtIoNS SAFe For Future uSe.
SA206 SA206Fr & SA206FrAD
1. SAFetY INStruCtIoNS
WArNINg! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.

WArNINg! Disconnect the equipment from the air supply before changing accessories, servicing or performing any maintenance.

Keep the equipment clean and maintain it in good condition (use an authorised service agent).

replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

WArNINg! Ensure that the correct air pressure is maintained and not exceeded.

Keep air hoses away from heat, oil and sharp edges. check hoses for wear before each use and ensure that all connections are secure.

Do Not direct air from the air hose at yourself, others or animals.

Drain the compressor air tank daily. Water in the air line will damage your equipment.

When work is complete ensure that the air supply is turned off.

2. INtroDuCtIoN & SPeCIFICAtIoNS
suitable for industrial workshop air supply set-ups where high volume applications are required. regulator assemblies feature locking control
knob for pre-setting air pressure and large easy-to-read pressure gauge. filters available with manual or auto drain facility with female
1/8"BsP outlet. Lubricator includes oil/air mix control and sight glass. filter and lubricator are fitted with metal bowl cages for protection.
sA206, sA206fr, sA206frAD and sA206r supplied with mounting bracket.
Filter/lubricator/regulator - SA206
Max. inlet pressure . . . . . . . . . . . . . . . . . . . . 150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . . . 125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .105cfm
filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 micron
Lubricant . . . . . . . .sealey Air tool oil - Ato/500 or Ato/1000
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BsP
Filter/regulator - SA206Fr, SA206FrAD
Max. inlet pressure . . . . . . . . . . . . . . . . . . . . 150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . . . 125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .140cfm
filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 micron
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BsP
Auto drain . . . . . . . . . . . . . . . . . . . . . . . . . . sA206frAD only
regulator - SA206r
Max. inlet pressure . . . . . . . . . . . . . . . . . . . . 150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . . . 125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .210cfm
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BsP
InstructIons for:
AIr regulAtor, FIlter, luBrICAtor rANge
Models: SA206, SA206Fr, SA206F, SA206l, SA206r,
SA206FrAD, SA206FAD.
SA206l SA206F & SA206FAD
lubricator - SA206l
Max. inlet pressure . . . . . . . . . . . . . . . . . . . . 150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . . . 125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .175cfm
Lubricant . . . . . . . .sealey Air tool oil - Ato/500 or Ato/1000
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
Filter - SA206F, SA206FAD
Max. inlet pressure . . . . . . . . . . . . . . . . . . . . 150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . . . 125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .140cfm
filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 micron
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BsP
Auto drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . sA206fAD only
WArNINg! Filter and lubricator bowls are manufactured
from polycarbonate and must not be used at temperatures
over 125°F (52°C) or for pressures over 218psi (15 bar).
Polycarbonate can be damaged and may fail if exposed to
certain solvents either internally or externally - strong
alkalies, compressor oils containing aromatic hydrocarbons
or fire retardant oils, or the fumes of any of these.
Clean with warm water only.
sA206/206fr/206f/206L/206r/206fAD/206frAD
SA206r
Issue: 2 - 05/09/08