Sealey VS0204A Quick Manual

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: pleAse ReAD These INsTRucTIONs cAReFullY. NOTe The sAFe OpeRATIONAl ReQuIRemeNTs, WARNINGs & cAuTIONs. use The pRODucT
cORRecTlY AND WITh cARe FOR The puRpOse FOR WhIch IT Is INTeNDeD. FAIluRe TO DO sO mAY cAuse DAmAGe AND/OR peRsONAl INJuRY AND WIll
INvAlIDATe The WARRANTY. keep These INsTRucTIONs sAFe FOR FuTuRe use.
Refer to
Wear eye
instructions protection
1. sAFeTY
 Keep this product in good working order and condition, take immediate action to repair or replace damaged parts.
 Use approved parts only. Unapproved parts may be dangerous and will invalidate the warranty.
 Keep children and unauthorised persons away from the work area.
 Keep work area clean and tidy and free from unrelated materials.
 Ensure the work area has adequate lighting.
 DO NOT use the kit to perform a task for which it is not designed.
 DO NOT allow untrained persons to use the kit.
 DO NOT use when tired or under the influence of drugs, alcohol or intoxicating medication.
 After use, clean equipment and store in a cool, dry, childproof area.
 Dispose of waste liquids in accordance with local authority regulations.
 Always read and comply with the warnings on the brake fluid container.
 Wear eye protection and keep skin contact to a minimum. If brake fluid enters eyes rinse with plenty of water and seek medical advice. If
swallowed seek medical advice immediately.
 WARNING! Only use new Brake Fluid, used Brake Fluid or other fluids will contaminate the system and possible brake system failure may
result.
 WARNING! DO NOT pollute the environment by allowing uncontrolled discharge of fluids.
 WARNING! Brake fluid is flammable - keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.
 WARNING! Brake fluid will damage paintwork. Any spillage should be flushed with water immediately.
 WARNING! DO NOT allow the fluid capacity in the unit to fall below ½ litre during the bleeding process otherwise air may enter
the system.
2. INTRODucTION
One-man pressure brake and clutch bleeding system suitable for the professional workshop. low pressure tank (20-40psi) can be
pre-charged with compressed air - making the unit fully portable. large reservoir means reduced risk of running the system dry during
bleeding process or complete fluid change. Suitable for use on ABS systems. Features a long delivery hose for operation with a low level
ramp and long reach handle for easy mobility. Supplied with Ø45mm cap with 90° angled connector which is suitable for most European
models. For other applications order optional Brake Reservoir Cap 45mm Straight Connector - model no. VS0204SA, Universal Adaptor -
model no. VS820UA or Brake & Clutch Bleeder Cap Set - model no. VS0204B.
3. specIFIcATION
model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vs0204A
maximum Air Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-40psi
Air consumption:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5cfm
Inlet size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Tank capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.0 litres
Hose length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7mtr
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8kg
© Jack Sealey limited
bRAke & cluTch pNeumATIc
pRessuRe bleeDeR
vs0204A
mODEl NO:
Fig.1
Original Language Version
VS0204A Issue:2 (2) - 18/09/18