Sealey SA59.V2 Instructions

Item Part No Description Qty
1 SA59.V2.01 Motor Housing
2 SA59.V2.02 End Cap
3 SA59.V2.03 End Cap Gasket
4 SA59.V2.04 Screw
5 SA59.V2.05 Spring Washer
6 SA59.V2.06 Anvil Bushing
7 SA59.V2.07 Oil Seal
8 SA59.V2.08 Clutch Housing
9 SA59.V2.09 O-Ring
10 SA59.V2.10 Protecting Rubber
11 SA59.V2.11 Muffle Cover
14 SA59.V2.14 Oil Plug
15 SA59.V2.15 Trigger
16 SA59.V2.16 Screw
17 SA59.V2.17 Spring Pin
18 SA59.V2.18 Throttle Bushing
19 SA59.V2.19 Throttle Pin
20 SA59.V2.20 Steel Ball
21 SA59.V2.21 Spring
22 SA59.V2.22 Hose Fitting
23 SA59.V2.23 Dust Cover
24 SA59.V2.24 Valve Sleeve
25 SA59.V2.25 O-Ring
26 SA59.V2.26 Reverse Valve
27 SA59.V2.27 Air Regulator
28 SA59.V2.28 O-Ring
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions, call us on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
Issue :
Date: 260602
Item Part No Description Qty
1 29 SA59.V2.29 Spring Pin 1
1 30 SA59.V2.30 Pin 1
1 31 SA59.V2.31 Spring 1
8 32 SA59.V2.32 Screw 1
8 33 SA59.V2.33 Bearing 1
1 34 SA59.V2.34 Oil Seal 2
1 35 SA59.V2.35 Frong End Plate 1
1 36 SA59.V2.36 O-Ring 1
1 37 SA59.V2.37 Spring Pin 1
1 38 SA59.V2.38 Cylinder 1
1 39 SA59.V2.39 Rotor 1
1 40 SA59.V2.40 Rotor Blade 6
1 41 SA59.V2.41 Rear End Plate 1
1 42 SA59.V2.42 Bearing 1
1 43 SA59.V2.43 Spring Pin 1
1 45 SA59.V2.45 Hammer Cage 1
1 46 SA59.V2.46 Drive Cam Base 1
1 47 SA59.V2.47 Steel Ball 1
1 48 SA59.V2.48 Drive Cam 1
1 49 SA59.V2.49 Hammer Bar 2
1 50 SA59.V2.50 Spring 1
1 51 SA59.V2.51 Anvil 1
1 52 SA59.V2.52 Anvil Washer 1
1 53 SA59.V2.53 O-Ring 1
1 54 SA59.V2.54 Anvil Collar 1
1
E-mail: sales@sealey.co.uk
01284 703534
Web Address: www.sealey.co.uk
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
! Follow all workshop safety rules, regulations, and conditions when using wrench.
F WARNING! Disconnect from air supply before changing accessories or servicing.
! Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
F WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
! Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
1
! Only use impact sockets which are specifically designed for use with an impact wrench.
! Wear approved safety eye/face shield, ear defenders, and hand protection.
F WARNING! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems we recommend you wear suitable respiratory protection.
! Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
! Keep children and non essential persons away from the working area.
% DO NOT use the wrench for a task it is not designed to perform.
F WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
p
% DO NOT use wrench unless you have been instructed in its use by a qualified person.
% DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
% DO NOT operate wrench if you are tired, under the influence of alcohol, drugs or intoxicating medication.
% DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
% DO NOT direct air from the air hose at yourself or others.
! When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATIONS
Tough professional air impact gun fitted with a
smooth performing,
Features an adjustable air/torque control and
reversible action plus spring balance anchorage
point. Fitted with standard 3/4” square drive anvil.
Suitable for general garage use.
Drive size . . . . . . . . . . . . . . . . . . . . . . . . . .3/4”
Working/Max torque . . . . . . . . . . .900/1000ft/lb
Ultimate torque . . . . . . . . . . . . . . . . . . 1050ft/lb
Air consumption . . . . . . . . . . . . . . . . . . .18cfm
Operating pressure . . . . . . . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . . . . . . . .1/4” BSP
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5kg
INSTRUCTIONS FOR
3/4” SQUARE DRIVE
SA59.V2
AIR IMPACT WRENCH
Model:
power-pin type clutch.
SA59.V2 - 1 - 260602