Mitsubishi Electric LGH-50RVS-E Installation Instructions Manual page 24

No.45
Supply fan monitor threshold
The threshold fan speed of supply fan monitor output can be
selected.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
N/A 45
- -
- -
No.46
Exhaust fan monitor threshold
The threshold fan speed of exhaust fan monitor output can be
selected.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
N/A 46
- -
- -
Automatic ventilation mode setting 1)
No.52
Outdoor and indoor temperature gap
Set one of conditions for By-pass mode in auto ventilation operation,
temperature gap between indoor and outdoor.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
N/A 52
- -
- -
- -
- -
Automatic ventilation mode setting 2)
No.53
The lowest outdoor temperature
Set one of conditions for By-pass mode in auto ventilation operation,
minimum outdoor temperature which comes in indoor directly.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
- -
- -
- -
N/A 53
- -
- -
- -
- -
- -
- -
- -
- -
Setting Supply fan monitor
check threshold
0
Fan speed 1 or higher
(Factory setting)
1 Fan speed 2 or higher
2 Fan speed 3 or higher
3 Fan speed 4
Setting Exhaust fan monitor
check threshold
0
Fan speed 1 or higher
(Factory setting)
1 Fan speed 2 or higher
2 Fan speed 3 or higher
3 Fan speed 4
Setting Gap between Indoor
check temp. and Outdoor temp.
0
0K (0˚C) or more
(Factory setting)
1 1K (1˚C) or more
2 2K (2˚C) or more
3 3K (3˚C) or more
4 4K (4˚C) or more
5 5K (5˚C) or more
6 6K (6˚C) or more
7 7K (7˚C) or more
Setting
Outdoor temperature
check
0 10˚C or more
1 11˚C or more
2 12˚C or more
3 13˚C or more
4 14˚C or more
5 15˚C or more
6
16˚C or more
(Factory setting)
7 17˚C or more
8 18˚C or more
9 19˚C or more
10 20˚C or more
11 21˚C or more
12 22˚C or more
13 23˚C or more
14 24˚C or more
15 25˚C or more
Automatic ventilation mode setting 3)
No.54
The lowest indoor temperature setting
Set one of conditions for By-pass mode in auto ventilation operation,
minimum indoor temperature.
This function is N/A from Lossnay unit DIP-SW.
When Lossnay is interlocked to Mr. Slim or City Multi indoor unit, the
target temperature of the indoor unit is the lowest indoor temperature
for By-pass mode
DIP-SW
Setting
check
SW No. Setting
- -
- -
- -
- -
- -
- -
- -
- -
N/A
- -
- -
- -
- -
- -
- -
- -
- -
User can set conditions to go into By-pass mode in automatic
ventilation mode by function
Setting examples are shown below.
Example 1*
By-pass/Heat recovery ventilation map in automatic ventilation
mode
40
Heat recovery ventilation area
38
36
34
32
30
28 Set by function
26
24
Set by function
(Target temp. of air conditioner)
22
20
18
16
14
12
10
8
8 10 12 14
Function No. Setting Data
52 0 (0˚C)
53 0 (10˚C)
54 2 (17˚C)
Eng-24
PZ-62DR-E
Setting
Indoor temperature
check
Function No. Setting Data
0 15˚C or more
1
16˚C or more
(Factory setting)
2 17˚C or more
3 18˚C or more
4 19˚C or more
5 20˚C or more
6 21˚C or more
7 22˚C or more
54
8 23˚C or more
9 24˚C or more
10 25˚C or more
11 26˚C or more
12 27˚C or more
13 28˚C or more
14 29˚C or more
15 30˚C or more
, , and
No. 52 No. 53 No. 54
No. 52
No. 54
By-pass ventilation area
Set by function
16 18 20 22 24 26 28 30 32 34 36 38 40
Indoor temperature (˚C)
.
No. 53