Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG APP10
Summary of Contents for AEG APP10
- Page 1 APP10...
- Page 2 mportant! It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product. Subject to technical modifications.
- Page 3 APP10...
- Page 4 OIL RESERVOIR BAR BOLT CHAIN BRANCH HOOK CHAIN TENSIONING SCREW...
- Page 5 ATTACHMENT SHAFT...
-
Page 6: Operating The Product
OPERATING THE PRODUCT 3-4 mm ADJUSTING THE CHAIN REPLACING THE CHAIN AND BAR FITTING AND REMOVING THE SCABBARD... -
Page 7: Installing The Attachment
INSTALLING THE ATTACHMENT STORING THE PRODUCT CLEANING THE PRODUCT... - Page 8 FITTING AND REMOVING THE SCABBARD...
- Page 9 INSTALLING THE ATTACHMENT NOTE: Always ensure that the inner shafts are fully seated together. If they are not, the chain does not spin and may cause damage to the inner shafts. click...
- Page 11 OPERATING THE PRODUCT ≤60˚ WARNING: DANGER! Risk electrocution! Do not operate within 10 ≥15m (50’) m of overhead electrical power lines. Position the product at an angle of 60° or less, depending on the specific situation. Keep bystanders at least 15 m away. WARNING: Do not cut from a ladder.
- Page 12 click...
- Page 13 click click...
- Page 14 NOTE: Make a shallow first cut (1/4 of the limb diameter) on the underside of the limb close to the main limb or trunk. Make a second cut from the top side of the limb outboard from the first cut. Lastly, make a final cut close to trunk.
- Page 15 3-4 mm ADJUSTING THE CHAIN NOTE: The chain tension is correct when the gap is 3–4 mm. Check the chain tension regularly, as the chain stretches when it heats up. 3-4 mm...
- Page 16 REPLACING THE CHAIN AND BAR NOTE: Refer to the Replacement Parts section on page 23 for the correct chain and bar replacements.
- Page 17 NOTE: Dispose the used chain and bar correctly. NOTE: Prepare the chain and bar. Make sure that the chain follows the correct direction as shown.
- Page 18 3-4 mm...
- Page 19 CLEANING THE PRODUCT NOTE: Clean all foreign material from the product using a soft brush or cloth. WARNING: Keep the product away from corrosive agents, such as garden chemicals and de-icing salts.
- Page 20 to p STORING THE PRODUCT NOTE: Store the product in a cool, dry, and well-ventilated place that is inaccessible to children. Keep the product away from corrosive agents, such as garden chemicals and de-icing salts. Do not store the product outdoors.
- Page 21 NOTE: Empty the chain oil tank after use to prevent leakage.
-
Page 22: Technical Data
Low speed ............................................................6.0 m/s max Iden such Bar length ............................................................10" (254 mm) Cutting capacity 58V AEG power head ....................................................... 8" (200 mm) 18V AEG power head ........................................................4" (100 mm) drive Min. branch diameter ........................................................1/4" (6 mm) Max. branch diameter (with 58V AEG power head ....................................................... - Page 23 FOR ASSEMBLING WITH ELECTRIC-DRIVEN POWER HEAD AND BATTERY-DRIVEN POWER HEAD The pruner attachment is approved for use only with the AEG 58V battery- WARNING! Read all safety warnings, instructions, illustrations and driven power heads of ALT58B and ALT58BT and the 18V battery-driven specifications provided with this power tool.
- Page 24 ■ ■ Prevent unintentional starting. Ensure the switch is in the off-position Do not use a battery pack or tool that is damaged or modified. before connecting to power source and/or battery pack, picking up or Damaged or modified batteries may exhibit unpredictable behaviour carrying the tool.
-
Page 25: Personal Protective Equipment
fied. suitable for outdoor use and has a current capacity sufficient to supply towards the operator. Either of these reactions may cause you to lose iour your product. Check the extension cable before every use for damage. control of the product, which could result in serious personal injury. Do Always uncoil the extension cable during use because coiled cables can not rely exclusively upon the safety devices built into the product. -
Page 26: Operation
WARNING! Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. Have the product serviced recommends the use of AEG bar and chain lubricant, which is available It ha by an authorised service centre only. When servicing, use only original from an AEG authorised service centre. -
Page 27: Know Your Product
ould tightness to ensure that the product is in safe working condition. Any part KNOW YOUR PRODUCT that is damaged should be properly repaired or replaced by an authorised See pages 4–5. service centre. ainst ■ Oil reservoir cap Maintenance schedule ■... - Page 28 Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC, 3149, Australia Techtronic Industries N.Z. Limited AEG is a registered trade mark used under Unit C, 70 Business Parade South, license from AB Electrolux (publ). Highbrook, Auckland 2013, New Zealand ©...