Sealey CPG12V.v3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ ThESE INSTRuCTIONS CAREFuLLY. NOTE ThE SAFE OPERATIONAL REQuIREMENTS, WARNINgS & CAuTIONS. uSE ThE PRODuCT
CORRECTLY AND WITh CARE FOR ThE PuRPOSE FOR WhICh IT IS INTENDED. FAILuRE TO DO SO MAY CAuSE DAMAgE AND/OR PERSONAL INJuRY AND WILL
INVALIDATE ThE WARRANTY. KEEP ThESE INSTRuCTIONS SAFE FOR FuTuRE uSE.
Refer to Instruction
Manual
1. SAFETY
1.1. MAINS POWER ELECTRICAL SAFETY (In relation to the battery charger)
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure the risk of electric shock is minimised by the installation of appropriate
safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend
that a Residual Current Device (RCD) be used. It is particularly important to use an RCD with portable products that are plugged into a
supply that is not protected by an RCCB. If in any doubt consult a competent electrician. You may obtain a Residual Current Device by
contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a competent
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operator. If in any doubt about electrical safety, contact a competent electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.3.1 and 1.3.2
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Inspect power supply cables and plugs regularly for wear or damage and check all connections to ensure none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating below.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or
replaced by a competent electrician. When an ASTA/BS approved UK 3 pin plug is damaged, cut the
cable just above the plug and dispose of the plug safely.
Ensure that the double insulated charger is correctly connected via a three-pin plug, as follows:
a) Connect the Brown live wire to live terminal 'L'.
b) Connect the Blue neutral wire to the neutral terminal 'N'.
c) After wiring, check that there are no bare wires, that all wires have been connected correctly, that the
cable outer insulation extends past the cable clamp and that the clamp is tight.
Note that the earth pin remains unconnected.
1.1.10.If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted
is preferred since any appliance plugged into it will be protected. The cable core section is important and
should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this
product and for others which may be used in the other output sockets, we recommend the use of 2.5mm² section cable. If an extension reel
is to be used outdoors, ensure it is marked for outdoor use.
1.2. BATTERY ChARgER SAFETY INSTRuCTIONS
WARNINg! DO NOT attempt to charge any battery other than that supplied for the wrench. Other types of batteries may explode!

All mains electrical supply safety features must be followed as described in 1.3 above.

Disconnect the charger from the mains supply when not in use.

DO NOT charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).

DO NOT expose the charger to damp or wet conditions.

DO NOT pull or carry the charger by the power lead.

DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take the charger to an authorised

agent for repair or obtain a replacement.
DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.

DO NOT insert foreign objects or material into the hole reserved for the battery pack.

DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger. Allow

the unit to cool for 15 minutes before charging the next pack.
DO NOT attempt to connect two chargers together.

1.3. gENERAL SAFETY
WARNINg! Disengage the grease gun from the battery before changing accessories, servicing or performing and

maintenance.
Maintain gun in good condition (use an authorised service agent).

Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate

the warranty.
Wear appropriate protective clothing. When handling lubricants refer to manufacturer's instructions and conform to local

regulations.
© Jack Sealey Limited
INSTRUCTIoNS FoR:
CORDLESS gREASE guN 12V
CPg12V.V3
MoDEL No:
Wear Eye
Protection
Original Language Version
RECOMMENDED
FuSE RATINg: 5AMP
CPG12V.V3 Issue:2(I) 08/12/16