Sealey AP28104BR Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Wear
Refer to
instruction protective
manual gloves
1. SAFETY
1.1 GENERAL SAFETY
 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations
are adhered to when using this product.
 WARNING! Use caution when handling and assembling the metal components. The metal may
have sharp edges or corners, the use of protective gloves is recommended.
 DO NOT open more than one drawer at a time.
 DO NOT step on the drawers.
 DO NOT let children play with the rollcab or topchest.
 Ensure all drawers are fully closed and the self locking catch is activated, before moving the toolbox.
 Secure the brakes when rollcab is in the desired position.
 Keep the work area clean, uncluttered and ensure there is adequate lighting.
 Keep the mounting frame clean and tidy in accordance with good workshop practice.
 DO NOT use in damp work areas.
 WARNING! The warnings, cautions and instructions referred to in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood that
common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2. INTRODUCTION
Retro styled tool chests with modern day functionality. Features drawers with ball bearing
slides and red anodised 'lift & latch' drawer pulls preventing inadvertent opening.
Heavy duty chrome plated side handles on chest and stainless handle on rollcab for easy
manoeuvrability. Topchest is further enhanced with chrome plated supports on the clam shell
lid for easy opening, providing additional storage. Rollcab features stylish heavy duty castors,
two with brakes. All drawers are fitted with castors and lock on one key turn.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AP28104BR . . . . . . . . . . . . . .AP28204BR
Overall Dimensions (W x D x H):. . . . . . . . 700 x 450 x 495mm . . . . . . . . 730 x 460 x 825mm
Medium drawer (x 4): . . . . . . . . . . . . . . . . . 570 x 400 x 60mm . . . . . . . . . . . . . . . . . . . . . n/a
Clam Shell Top: . . . . . . . . . . . . . . . . . . . . . . 590 x 430 x 80mm . . . . . . . . . . . . . . . . . . . . n/a
Large drawer (x1): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . n/a . . . . . . . . 570 x 400 x 105mm
Large drawer (x3): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . n/a . . . . . . . . 570 x 400 x 135mm
4. ASSEMBLY
4.1. Roll Cab Handle Installation.
Position the handle over the holes in the roll cab, attach using the M6 x 12mm hex bolts
and tighten securely (fig.1). Assembling the handle first will make it easier to handle the
the roll cab.
4.2. Castor Installation.
4.2.1. Lay the roll cab carefully on its back, protecting it with a soft mat placed on the floor.
4.2.2. Position the two rigid castors at the end opposite the handle.
4.2.3. Insert the M8 x 20mm hex bolts through the washers, then through the castors and into
the base of the roll cab, tightening securely.
4.2.4. Repeat with the two swivel castors on the opposite (handle) end.
4.3. Roll Cab and Top Chest Connection.
4.3.1. Place the top chest onto the roll cab.
4.3.2. Snap the connectors into the square holes on the back of the top chest (fig.3).
4.3.3. Fasten the connectors with the screws provided.
© Jack Sealey Limited
INSTRUCTIONS FOR:
TOPCHEST 4 DRAWER RETRO, ROLLCAB 4 DRAWER RETRO -
BLACK WITH RED ANODISED DRAWER PULLS
AP28104BR, AP28204BR
MODEL No's:
Original Language Version
Shown with
Mid-box
Model no:
AP28102BR
fig.1
fig.2
fig.3
AP28104BR, AP28204BR Issue: 1 - 18/05/16