Advertisement
Available languages
Available languages
Gasket
• Water tight conduit connections are required when
1. 7 50
1.372
using knock-outs on mounting box.
1. 7 50
1.372
4.300
• For irregular surfaces (block, brick, etc), caulk the wall
4.300
plate or mounting box to surface interface with
generic non-hardening sealant (not provided) across
the top, and both sides (Figure 4)
3
WIRING
• Reinstall Button PE, Motion sensor, or Transformer if
previously removed (Figure 3).
• Position fixture in vicinity of mounting box or plate.
• Make electrical connections in accordance with the
National Electrical Code and any applicable local code
requirements.
• Connect supply leads using wire nuts and fixture wiring
with quick connects.
• Use two provided screws to install housing to box or
plate. For ADA Compliant wall plate installations, use
shorter set of screws and tighten screws until fixture is
Button PE
Option
Button PE
less than 4" from the wall.
Option
• Insert two provided plugs into housing cover screw holes.
4
MAINTENANCE/CLEANING
• To maintain light output, occasional cleaning of the
outer lens surface may be needed.
• Use a mild, non-abrasive soap or detergent, of neutral
pH (pH 6 to 8) containing no chlorinated or aromatic
Button PE
hydrocarbons.
Option
Button PE
• Wash using a soft cloth. Rinse with clean, cold water
Option
and wipe dry.
4.300
5
STORAGE
4.300
• Packaged units should NOT be stored unprotected
Gasket
outdoors in corrugated boxes (cardboard boxes).
• Store packaged units in a covered dry area not
Motion Sensor
exceeding -40°C (-40°F) to 50°C (122°F) such as a
Motion Sensor
Option
Option
roofed area or covered with a secured tarp to keep
water off the corrugated (cardboard) packaging.
8.267
6
OCCUPANCY SENSOR (OPTIONAL)
• The occupancy sensor ships with a default program.
Remote Programmer part number: (Sold Separately
as 197634).
• Photoelectric control is integrated through the motion
sensor, and is offered as standard.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation,
operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's purposes, the
matter should be referred to GE.
1/2 " Conduit
Knock Out
3 Places
45°
45°
4.800
4.800
7.366
3.853
1.375
1.750
1.375
1.750
Gasket
All trademarks are the property of their respective owners. Information provided is subject to
change without notice. All values are design or typical values when measured under laboratory
conditions. Current, powered by GE is a business of the General Electric Company.
Gasket
© 2017 GE.
www.currentbyge.com
4.800
1.000
Housing
0.190 TYP
Housing
0.190 TYP
1.690
0.970
1.690
0.970
1.750
1.750
Figure 1: Wall Plate Install
Figure 2: Mounting Box Install
Incoming
Supply
0.190
0.190
45°
0.970 1.688
45°
0.970 1.688
1.750
Figure 3: Button PE Wiring
1.750
1. 7 50
4.300
Figure 4: Plate / Mounting Box Installed
GEH6060 (Rev 0 /
/1 ) English
Button PE
Wall Plate
Housing
Gasket
Housing
Gasket
Housing
Housing Gasket
Housing
Housing Gasket
Mounting Box
Mounting Box
White
Black
RED
White
Black
LED
Driver
Gasket
45°
1.372
4.800
Wall Plate
Wall
Gasket
Wall
Gasket
Wall Gasket
Wall Gasket
Knockout
Plug
Knockout
Plug
PE
0.190 TYP
1.690
0.970
1.750
Housing
H
Advertisement
