Related Manuals for Siemens Albatros RVS46 Series
Summary of Contents for Siemens Albatros RVS46 Series
- Page 1 RVS46.. AVS75.. AVS37.. Albatros QAA75.. Zone controller QAA78.. User Manual QAA55.. Edition 3.0 CE1U2353en 2014-07-30 Building Technologies...
- Page 2 2/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
-
Page 3: Table Of Contents
Planning ......................22 Mounting method ................... 22 Connections ....................22 Dimensions and drilling plan ................23 Wireless components ..................24 3.8.1 Radio module AVS71.390 ................24 Planning ......................24 Mounting method ................... 24 3/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30... - Page 4 Adjusting the room temperature setpoint ............55 Adjusting the nominal DHW setpoint ............. 55 Displaying information ..................55 Setting principle ..................... 56 Example: “Setting the time of day“Error! No bookmark name given....56 4/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
- Page 5 Buffer storage tank / primary controller ............76 Remote control ....................76 Cooling circuit ....................77 Operating mode ..................... 77 Setpoints ......................77 Release ......................77 Cooling curve ....................77 ECO ....................... 78 Summer compensation .................. 78 5/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
- Page 6 Building and room model ................103 Frost protection for the plant ................ 103 External requirements .................. 104 Air dehumidifier .................... 104 Sensor state ....................105 Parameter reset ................... 105 Plant diagram ....................105 6/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
- Page 7 Extension module AVS75.390 ..............125 Operator unit and room units AVS37... / QAA7x… / QAA55....... 126 Power supply AVS16.290 ................128 Radio module AVS71.390 ................129 Wireless outside sensor AVS13.399 ............130 7/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
- Page 8 Radio repeater AVS14.390 ................131 Sensor characteristics .................. 132 8.8.1 NTC 1 k ......................132 8.8.2 NTC 10 k ...................... 133 8.8.3 PT1000 ......................133 Revision history .................... 137 8/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
-
Page 9: Overview
The following products are described in separate pieces of documentation: QAC34 Outside sensor NTC 1 kΩ QAD36 Strap-on temperature sensor NTC 10 kΩ QAZ36 Immersion temperature sensor NTC 10 kΩ 9/138 Siemens User Manual CE1U2353en Building Technologies Product range overview 2014-07-30... -
Page 10: Product Range Overview
BSB-RF OCI611 OCI700 BSB-W Extension module Basic Unit mod. AVS75… RVSxx (max. 2) BSB : Boiler System Bus Basic Unit RVS... LPB : Local Process Bus 10/138 Siemens User Manual CE1U2353en Building Technologies Product range overview 2014-07-30... -
Page 11: Operating Options
(optionally with additional room unit) Basic unit RVS… Room unit QAA75… / 78… / QAA55.. Outside sensor AVS13… Operator unit AVS37.294 (clear-text) Operator unit AVS37.390 (basic) Radio module AVS71… 11/138 Siemens User Manual CE1U2353en Building Technologies Product range overview 2014-07-30... -
Page 12: Safety Notes
· When using the products, all requirements specified in the chapters on "Handling" and "Technical data" must be satisfied · The local regulations (for installation, etc.) must be complied with · Do not open the units. If not observed, warranty becomes void. 12/138 Siemens User Manual CE1U2353en Building Technologies Product liability... -
Page 13: Mounting And Installation
· Power cables must be clearly segregated from low-voltage cables (sensors) observing a distance of at least 100 mm · Boiler Mounting location · Control panel · Housing for wall mounting 13/138 Siemens User Manual CE1U2353en Building Technologies Regulations 2014-07-30... -
Page 14: Mounting Method
Dimensions and drilling plan Dimensions in mm RVS46.543 RVS46.530 2359Z10 Total height required Masse X: Connectors with tongues minimum 70 mm Connector without tongues minimum 60 mm 14/138 Siemens User Manual CE1U2353en Building Technologies Basic units RVS… 2014-07-30... -
Page 15: Rvs46.530 Connection Terminals
3.2.1 RVS46.530 connection terminals 060706A RVS46.530/109 000020 S060706000020 1PRVS46.530/109 3.2.2 RVS46.543 connection terminals 060404A RVS46.543/109 000020 S060404000020 1PRVS46.543/109 15/138 Siemens User Manual CE1U2353en Building Technologies Basic units RVS… 2014-07-30... -
Page 16: Terminal Markings
Digital / DC 0...10 V input AGP4S.02F/109 Ground Flow sensor heating circuit 1 AGP4S.02G/109 Ground Multifunctional sensor input 1 AGP4S.02F/109 Ground Multifunctional sensor input 2 AGP4S.02F/109 Ground RVS46.530 RVS46.543 16/138 Siemens User Manual CE1U2353en Building Technologies Basic units RVS… 2014-07-30... -
Page 17: Extension Module Avs75.390
X50 of the basic unit using the AVS83.490/109 connecting cable. The connectors are coded. 3.3.1 AVS75.390 connection terminals 050110A AVS75.390/109 000020 S050110000020 1PAVS75.390/109 = Modul 1 = Modul 2 17/138 Siemens User Manual CE1U2353en Building Technologies Extension module AVS75.390 2014-07-30... -
Page 18: Terminal Markings
Assignment of terminals The two parameters · Function extension module 1 (operating line 6020) · Function extension module 2 (operating mode 6021) define the usage of the respective module. 18/138 Siemens User Manual CE1U2353en Building Technologies Extension module AVS75.390 2014-07-30... -
Page 19: Operator Unit Avs37.294
The AVS37.294 operator unit must be connected to terminal X30 of the basic unit using the AVS82.491/109 connecting cable. The connectors are coded. Ground 42.4 Panel cutout (144) 0.5...3.0 19/138 Siemens User Manual CE1U2353en Building Technologies Operator unit AVS37.294 2014-07-30... -
Page 20: Operator Unit Avs37.390
3.5 Operator unit AVS37.390 Connections The AVS37.390 operator unit must be connected to terminal X30 of the basic unit using the AVS82.491/109 connecting cable. The connectors are coded. Dimensions Control panel, front 20/138 Siemens User Manual CE1U2353en Building Technologies Operator unit AVS37.390 2014-07-30... -
Page 21: Room Unit Qaa55
When the unit is removed from its base, power is cut off so that the unit is out of operation. Mounting method · The controller must not be exposed to dripping water Connections BSB data BSB ground Dimensions and drilling plan 21/138 Siemens User Manual CE1U2353en Building Technologies Room unit QAA55… 2014-07-30... -
Page 22: Room Unit Qaa75
When the unit is removed from its base, power is cut off so that the unit is out of operation. Mounting method Connections Terminal Designation QAA75.610 QAA75.611 BSB data BSB data BSB ground BSB ground Reserved Power supply DC 12 V 22/138 Siemens User Manual CE1U2353en Building Technologies Room unit QAA75… 2014-07-30... -
Page 23: Dimensions And Drilling Plan
Dimensions and drilling plan 2359Z12 23/138 Siemens User Manual CE1U2353en Building Technologies Room unit QAA75… 2014-07-30... -
Page 24: Wireless Components
Prior to connecting, the basic unit must be disconnected from power! Radio connection Establishment of the wireless connection is described in the following sections which cover the relevant radio-controlled units. Dimensions and drilling plan 24/138 Siemens User Manual CE1U2353en Building Technologies Wireless components 2014-07-30... -
Page 25: Room Unit Qaa78.610
(about 1.5 meters above the floor) · In the case of wall mounting, there must be sufficient clearance above the unit, enabling it to be fitted and removed Mounting with base 25/138 Siemens User Manual CE1U2353en Building Technologies Wireless components 2014-07-30... -
Page 26: Connection / Power Supply
On the room unit, as described above (points 2 through 4), select operating page “Radio“ and activate the test mode on setting line “Test mode“ (line 121). 26/138 Siemens User Manual CE1U2353en Building Technologies... -
Page 27: Dimensions And Drilling Plan
If the test was not successful, some other mounting location is to be selected or the AVS14.390 radio repeater can be used. Dimensions and drilling plan 2359Z12 27/138 Siemens User Manual CE1U2353en Building Technologies Wireless components 2014-07-30... -
Page 28: Wireless Outside Sensor Avs13.399
The outside sensor is to be connected to the radio transmitter via a 2-core cable, the connections are interchangeable. The room unit is powered by 2 pieces 1.5 V alkaline batteries type AAA (LR03). 28/138 Siemens User Manual CE1U2353en Building Technologies... -
Page 29: Radio Connection
7. After the test, press the button on the transmitter of the wireless outside sensor again briefly until the LED extinguishes. Dimensions and drilling plan 79,8 49,7 Ø 14,1 24,5 49,5 29/138 Siemens User Manual CE1U2353en Building Technologies Wireless components 2014-07-30... -
Page 30: Radio Repeater Avs14.390
12. When radio communication works, the LED on the radio module flashes briefly at 10-second intervals. 13. After the test, press the button on the radio repeater again briefly until the LED extinguishes. Dimensions and drilling plan 30/138 Siemens User Manual CE1U2353en Building Technologies Wireless components 2014-07-30... -
Page 31: Checking The Wireless Components
For detailed diagnostics of the plant, check operating pages “Diagnostics heat source" and “Diagnostics consumer”. 4.1 Basic units Checking the LED LED off: No power supply LED on Ready LED flashes Local fault 31/138 Siemens User Manual CE1U2353en Building Technologies Basic units 2014-07-30... -
Page 32: Handling
Confirmation of setting Quitting the setting verlassen Service socket (BSB) AVS37.294/109 Manual operation No function AVS37.394/109 AVS37.294/509 AVS37.294/209 No button No button AVS37.294/309 No function, Reset Cooling button 32/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30... -
Page 33: Display Options
· Heating mode with no time program · Protective functions active · Automatic summer / winter changeover (ECO functions) and 24-hour heating limit inactive in the case of continuous operation with Comfort setpoint 33/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. -
Page 34: Selection Of Cooling Mode
The programming allows for setting the reduced setpoint and the frost protection setpoint After each readjustment, wait at least 2 hours, allowing the room temperature to adapt. 34/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30... -
Page 35: Occupancy Button
AUTO Error 30:Flow sensor 1 Error Text3 Text4 30:Flow sensor 1 Text3 Text4 A list of possible displays is given on page 114. 35/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30... - Page 36 If released, the test will be aborted. The SLT test is shown on the display. The test may only be made by qualified staff since the boiler temperature will be raised above the maximum limits. 36/138 Siemens User Manual CE1U2353en Building Technologies QAA75..
-
Page 37: Programming
AUTO Turn the setting knob until the hours of the time of day are correct. Time of day and date To confirm, press OK. Hours / minutes 37/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30... -
Page 38: User Levels
Operator section You are now given a choice of user AUTO levels. Turn the setting knob until the required user level is reached. Enduser Text3 Commissioning Press OK. 38/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30... -
Page 39: Setting The Structure "End User
Time program heating circuit 1 Start of summer time Time program heating circuit 2 End of summer time Time program heating circuit P Holidays heating circuit 1 Diagnostics of consumers 39/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30... -
Page 40: Overview Of Settings
Missing ¦ Ready ¦ No recept’n ¦ Change batt Room unit 2 Missing ¦ Ready ¦ No recept’n ¦ Change batt Room unit P Missing ¦ Ready ¦ No recept’n ¦ Change batt 40/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30... - Page 41 Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa ¦Su 1. phase on 6:00 00:00 24:00 hh:mm 1. phase off 22:00 00:00 24:00 hh:mm 41/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 42 °C Heating curve slope 1.50 0.10 4.00 Heating curve displacement -4.5 °C Heating curve adaption Off ¦ On - - - / 8 Summer/winter heating limit °C 42/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 43 - - - / 1 Room influence - - - / 0.5 Room temp limitation °C Mixing valve cooling offset °C Actuator type 3-position 2-position ¦ 3-position 43/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 44 Actuator running time 1150 Floor curing function Off ¦ Functional heating ¦ Curing heating ¦ Functional/ curing heating¦ Curing/functional heating ¦ Manually 1151 Floor curing setp manual °C 44/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 45 Excess heat draw Always Off ¦ Heating mode ¦ Always 1470 With buffer storage tank No ¦ Yes 1472 With primary controller / system pump No ¦ Yes 45/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 46 Charg temp min DHW st tank °C 3831 Min run time collector pump - - - - - - / 1 3834 Collector start funct gradient Min/°C 46/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 47 2nd pump speed HC1 Q21 ¦ 2nd pump speed HC2 Q22 ¦ 2nd pump speed HCP Q23 ¦ Heat circuit pump HCP Q20 ¦ H2 pump Q18 ¦ System pump Q14 ¦ Scheduler 5 47/138 Siemens User Manual CE1U2353en Building Technologies QAA75..
- Page 48 HCP Q20 ¦ H2 pump Q18 ¦ System pump Q14 ¦ Scheduler 5 K13 ¦ DHW mixing pump Q35 ¦ DHW iterm circ pump Q33 ¦ Heat request K27 ¦ Refrig 48/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 49 24 h/day 24h/day ¦ Time progr. heating circuit ¦ Time program 5 6137 Air dehumidifier r.h. EIN 6138 Air dehumidifier r.h. SD 6200 Save sensors No ¦ Yes 49/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 50 Error code 5 6810 History 6 Error code 6 6812 History 7 Error code 7 6814 History 8 Error code 8 6816 History 9 Error code 9 50/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 51 -28.0 °C 8512 Collector temp 1 min -28.0 °C 8513 dT collector 1/DHW -168.0 °C 8519 Solar flow temp -28.0 °C 8520 Solar return temp -28.0 °C 51/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 52 Off ¦ On 8830 DHW temp 1 °C 8831 DHW temp setpoint °C 8832 DHW temp 2 °C 8835 DHW circulation temp °C 8836 DHW charging temp °C 52/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
- Page 53 9053 Relay output QX21 module 2 Off ¦ On 9054 Relay output QX22 module 2 Off ¦ On 9055 Relay output QX23 module 2 Off ¦ On 53/138 Siemens User Manual CE1U2353en Building Technologies QAA75.. / QAA78… / AVS37.. 2014-07-30...
-
Page 54: Avs37.390
Press the button to switch from heating mode on / off to DHW heating, and vice versa. The selection made is indicated by a bar which appears below the respective symbol. 54/138 Siemens User Manual CE1U2353en Building Technologies AVS37.390 2014-07-30... -
Page 55: Adjusting The Room Temperature Setpoint
Chimney sweep function To start the chimney sweep function , press the button for a moment (< 3 seconds). This function produces the operating state required to make emission measurements (flue gas). 55/138 Siemens User Manual CE1U2353en Building Technologies AVS37.390... -
Page 56: Setting Principle
(e.g. 50). Press OK to confirm. The display shows the hours flashing. Press the "+/-" button until the hours of the time of day are correct. Press OK to confirm. 56/138 Siemens User Manual CE1U2353en Building Technologies AVS37.390 2014-07-30... -
Page 57: User Levels
Press INFO for 3 seconds. You are on the user level “Heating engineer”. If the change to the “Heating engineer” level was successful, the display shows “ON” as a confirmation. 57/138 Siemens User Manual CE1U2353en Building Technologies AVS37.390 2014-07-30... -
Page 58: Overview Of Settings
0.10 4.00 °C 88 1021 F Heating curve displacement -4.5 °C 89 1030 E Summer/winter heating limit - - - / 8 °C 90 1041 F Flow temp setpoint max °C 58/138 Siemens User Manual CE1U2353en Building Technologies AVS37.390 2014-07-30... -
Page 59: Qaa55
Characteristics of automatic mode: Heating mode according to the time program Temperature setpoints according to the heating program "Comfort setpoint" "Reduced setpoint" Protective functions active Automatic summer / winter changeover (ECO functions) 59/138 Siemens User Manual CE1U2353en Building Technologies QAA55.. 2014-07-30... -
Page 60: Display Cooling Mode
When the rooms are occupied again, press again the occupancy button. · The occupancy button is only active in automatic operation · The current selection is active until the next switching action according to the timeswitch program takes place 60/138 Siemens User Manual CE1U2353en Building Technologies QAA55.. 2014-07-30... -
Page 61: Programming
Operating level changeover (occupancy button) OFF is displayed for 3 seconds when pressing a locked button when operating lock is active. The operating lock does not prevent entry to the service level. 61/138 Siemens User Manual CE1U2353en Building Technologies QAA55.. -
Page 62: The Settings In Detail
· Constant deactivation of programming lock. First, make the temporary deactivation, then go to operating line “Programming lock“ (operating line 27) and deactivate the programming lock 62/138 Siemens User Manual CE1U2353en Building Technologies Time of day and date... - Page 63 “Assignment room unit 1” and activated in the basic unit. Room unit 2 The operator unit only supports heating circuit 2. Operator unit / service unit The operator unit supports the heating circuits activated in the basic unit. 63/138 Siemens User Manual CE1U2353en Building Technologies Operator section 2014-07-30...
-
Page 64: Heating Circuit Assignment
Line no. Operating line Readjustment room sensor The temperature display can be readjusted. Device data Line no. Operating line Software version The display shows the current version of the room unit. 64/138 Siemens User Manual CE1U2353en Building Technologies Operator section 2014-07-30... -
Page 65: Radio
When preselecting groups of days like for instance Mo...Fr and Sa...Su that use the same switching times, setting of the switching programs is simplified. 65/138 Siemens User Manual CE1U2353en Building Technologies... -
Page 66: Switching Points
(operating line 1300). This setting is used to switch between the different operating modes. The functionality corresponds to operating mode selection with the operating mode button. For details, refer to section ”Operation“. 66/138 Siemens User Manual CE1U2353en Building Technologies Holidays... -
Page 67: Setpoints
Lowers the flow temperature, especially when outside temperatures are low. The programmed heating curve is based on a room setpoint of 20°C. If the room setpoint is adjusted, the heating curve automatically adapts to the new value. 67/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits... -
Page 68: Eco Functions
· The function is not active in operating mode ”Continuously Comfort temperature“ · The display shows ECO · To give consideration to the building’s thermal dynamics, the outside temperature will be attenuated Example: 68/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits 2014-07-30... -
Page 69: Flow Temperature Setpoint Limits
If the flow temperature setpoint demanded by the heating circuit reaches the relevant limit and the heat request increases or decreases, the flow temperature setpoint will be maintained at the maximum or minimum limit. 69/138 Siemens User Manual CE1U2353en Building Technologies... -
Page 70: Room Influence
For example, a slight increase of the room temperature causes an immediate drop of the following temperature. To activate the function, following must be considered: · A room sensor must be connected. 70/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits 2014-07-30... -
Page 71: Room Temp Limitation
A higher setting leads to shorter heating up times, a lower setting to longer heating up times. · Boost heating is possible with or without room sensor 71/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits... -
Page 72: Quick Setback
0 °C 15.8 -5 °C 12.5 -10 °C 10.3 -15 °C -20 °C Duration of quick setback in hours · Quick setback is possible with or without a room sensor 72/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits 2014-07-30... -
Page 73: Optimum Start / Stop Control
When the Reduced setpoint is raised, the rooms are prevented from cooling down to too low levels, thus shortening the heating up time when changing to the Comfort setpoint. 73/138 Siemens User Manual CE1U2353en Building Technologies... -
Page 74: Overtemp Prot Pump Circuit
The value set here is added to the request. Actuator running time Setting the running time of the actuator used with the mixing valve. 74/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits... -
Page 75: Floor Curing Function
· The function can be aborted by choosing Off. · Maximum limitation of the flow temperature remains active. [TVw] [Tag Fh + Bh Start day Functional heating Floor curing heating 75/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits 2014-07-30... -
Page 76: Excess Heat Draw
None ¦ Protection ¦ Reduced ¦ Comfort ¦ Automatic In the case of external changeover via inputs H1 / H2 / H3, the operating mode to be used can be selected. 76/138 Siemens User Manual CE1U2353en Building Technologies Heating circuits... -
Page 77: Cooling Circuit
Cooling is enabled in accordance with the heating circuit time program Time program 5 Cooling is enabled in accordance with time program 5. Cooling curve Line no. Operating line Flow setpoint at OT 25°C Flow setpoint at OT 35°C 77/138 Siemens User Manual CE1U2353en Building Technologies Cooling circuit 2014-07-30... -
Page 78: Eco
Start of summer Summer compensation starts to take effect at the outside temperature set here. If the compensation at OT outside temperature continues to rise, the comfort setpoint is raised in parallel. 78/138 Siemens User Manual CE1U2353en Building Technologies Cooling circuit... -
Page 79: Flow Temperature Setpoint Limits
Flow temperature setpoint for cooling (with low limit control) TVKw_unb Flow temperature setpoint for cooling (without low limit control) TAgem Composite outside temperature Room influence Line no. Operating line Room influence Compensation variants 79/138 Siemens User Manual CE1U2353en Building Technologies Cooling circuit 2014-07-30... -
Page 80: Room Temp Limitation
The cooling circuit pump is activated again as soon as the room temperature returns to a level above the current room temperature setpoint. While the “Room temperature limitation“ function is active, no cooling request is sent to the heat source. 80/138 Siemens User Manual CE1U2353en Building Technologies Cooling circuit... -
Page 81: Mixing Valve Control
The valve is used for control in heating and cooling mode. Open The valve is used for control in cooling mode and is open in heating mode. Dewpoint monitoring Line no. Operating line Dewpt monitor locking time 81/138 Siemens User Manual CE1U2353en Building Technologies Cooling circuit 2014-07-30... - Page 82 The humidity sensor must be assigned to an H.. input as "Relative room humidity 10V", and a room temperature sensor must also be available (assigned to the H.. input as "Room temperature 10V" or room unit). 82/138 Siemens User Manual CE1U2353en Building Technologies...
-
Page 83: Buffer Storage Tank / Primary Controller
DHW storage tank. TWWN TWWmax TWWR °C TWWR DHW reduced setpoint TWWN DHW nominal setpoint TWWmax DHW nominal setpoint maximum 83/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30... -
Page 84: Release
The mixing and pump heating circuit stay locked until DHW heating is finished. Shifting priority If the capacity of the heat source is not sufficient, the mixing and pump heating circuit will be restricted until DHW is heated up. 84/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30... -
Page 85: Legionella Function
If a sensor is installed in the DHW distribution pipe, the controller will monitor its actual value during the time the legionella function is performed. The adjusted setpoint must be maintained at the sensor during the adjusted “Dwelling time“. 85/138 Siemens User Manual CE1U2353en Building Technologies... -
Page 86: Hx Pumps
If the plant uses a buffer storage tank, it is to be set here whether, hydraulically, the primary controller or the system pump is installed upstream from the buffer storage tank. 86/138 Siemens User Manual CE1U2353en Building Technologies Hx pumps... -
Page 87: Solar
TKol < TKolFrost. · When the collector temperature returns to a level of 1°K above the frost protection temperature, the collector pump will be deactivated again: TKol > TKolFrost + 1. 87/138 Siemens User Manual CE1U2353en Building Technologies Solar... -
Page 88: Overtemperature Protection For The Collector
Pump capacity The flow rate in l/h of the pump used must be determined and serves for calculating the volume delivered. 88/138 Siemens User Manual CE1U2353en Building Technologies Solar 2014-07-30... -
Page 89: Dhw Storage Tank
This can be selected separately for each heating circuit (operating page heating circuit 1…). · If the collector is cold, the energy can be emitted to the environment via the Recooling collector collector’s surfaces. 89/138 Siemens User Manual CE1U2353en Building Technologies DHW storage tank 2014-07-30... -
Page 90: Electric Immersion Heater
The electric immersion heater is switched on and off according to DHW release. Example: Time program 4/DHW For the electric immersion heater, time program 4 / DHW of the local controller is taken into account. Example: 90/138 Siemens User Manual CE1U2353en Building Technologies DHW storage tank 2014-07-30... -
Page 91: Excess Heat Draw
6.13 Instantaneous DHW heater RVS46.543 only Mixing valve control Line no. Operating line 5544 Actuator running time Actuator running time Setting the running time of the actuator used with the mixing valve. 91/138 Siemens User Manual CE1U2353en Building Technologies Instantaneous DHW heater 2014-07-30... -
Page 92: Configuration
Use of mixing valve 1 Heating Cooling Heating and cooling HC/CC Y1/Y2 The setting is required when a QX… relay output (configuration) is used as a diverting cooling valve Y21. 92/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... -
Page 93: Dhw Sensor B3
H2 pump Q18 System pump Q14 Time program 5 K13 DHW mixing pump Q35 DHW interm circ pump Q33 Heat request K27 Refrig demand K28 Dehumidifier K29 Diverting valve, cooling Y21 93/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... - Page 94 Heating circuit pump HCP Q20 Pump heating circuit P will be activated. · Time program For heating circuit P, only time program 3/HCP is available. For more detailed information, refer to section "Time program". 94/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30...
-
Page 95: Input Sensor Bx
Draw off via 4-pipe system Input sensor BX Line no. Operating line 5930,5931 Sensor input BX1, 2, 3, 4 RVS46.543 only None DHW sensor B31 Collector sensor B6 DHW circulation sensor B39 95/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... -
Page 96: Input H1
The adjusted minimum flow temperature setpoint will be activated via terminals H1/2 (e.g. an air heater function for a warm air curtain) closes its contact. The setpoint must be set via operating line 5952. 96/138 Siemens User Manual CE1U2353en Building Technologies... - Page 97 The voltage signal present at input Hx is converted into a linearized relative humidity value. This is used for the dewpoint calculation and dewpoint protection functions of the cooling circuit and for control of the dehumidifier. 97/138 Siemens User Manual CE1U2353en Building Technologies...
- Page 98 Function value and Voltage value (F nd F Voltage value 2 · Example for "Heating demand 10V" and "Cooling demand 10V" Function value 2 Voltage value 1 Function value 1 Voltage value 2 Function value 2 98/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30...
- Page 99 · Example of room temperature 10V Voltage value 1 Function value 1 Voltage value 2 Function value 2 If the measured value is below 0.15V it is regarded as invalid and an error message is generated. 99/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30...
-
Page 100: Mixing Valve Groups Basic Unit
For this application, the respective settings of operating page “Cooling circuit 1” can be adapted. Heating circuit/cooling circuit 1 For this application, the respective settings of operating page “Heating circuit 1 and cooling circuit 1” can be adapted. 100/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... -
Page 101: Extension Module
Connections: QX21 QX22 QX23 BX21 BX22 Page Multifunction Heating circuit Solar DHW heating Primary controller DHW primary controller Instantaneous Flow DHW heater switch Cooling circuit * Freely selectable in QX…/ BX... 101/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... -
Page 102: Qx Extension Module
Room temperature 10V 6047 Contact type H2 6048 Function value, contact H2 6049 Voltage value 1, H2 6050 Function value 1, H2 6051 Voltage value 2, H2 6052 Function value 2, H2 102/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... -
Page 103: Types Of Sensor/Readjustment
Outside temperature Pump Graph (OT) ...-4 °C Continuously on -5…1.5 °C ON for 10 minutes at 6-hour intervals Cycle (takt) 1.5 °C... Continuously off takt TA °C 103/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... -
Page 104: External Requirements
The air dehumidifier is switch off again when room humidity drops below the set switching difference. Relative room humidity is measured via any Hx input with the functions Relative room humidity 10V. 104/138 Siemens User Manual CE1U2353en Building Technologies Configuration... -
Page 105: Sensor State
Solar with collector sensor and pump Check-No. storage tank DHW storage tank No DHW storage tank electric immersion heater Solar connection Charging pump Charging pump, solar connection Diverting valve Diverting valve, solar connection 105/138 Siemens User Manual CE1U2353en Building Technologies Configuration 2014-07-30... -
Page 106: Device Data
6.15 LPB system Address / power supply Line no. Operating line 6600 Device address 6601 Segment address 6604 Bus power supply function Automatically 6605 Bus power supply state 106/138 Siemens User Manual CE1U2353en Building Technologies LPB system 2014-07-30... -
Page 107: Central Functions
The range of the generation lock via H input is as follows: Manual source lock · Locally: Local action; the local source is locked. · Centrally: Central action; all sources of the cascade are locked. 107/138 Siemens User Manual CE1U2353en Building Technologies LPB system 2014-07-30... -
Page 108: Clock
· Master: The time of day on the controller can be readjusted The time of day on the controller is used for the system. The system time will be readjusted 108/138 Siemens User Manual CE1U2353en Building Technologies LPB system... -
Page 109: Faults
Locked released RVS46.543 only 7120 Economy mode Off ¦ On Economy function Locked Economy mode is not possible. Released Economy mode can be activated. Economy mode Switches economy mode on or off 109/138 Siemens User Manual CE1U2353en Building Technologies Faults 2014-07-30... -
Page 110: Manual Operation
During simulation, calculation of the 3 mentioned outside temperatures continues and the temperatures are available again when simulation is completed. The function is deactivated by setting -.- on this operating line, or automatically after a timeout of 1 hour. 110/138 Siemens User Manual CE1U2353en Building Technologies Maintenance / special mode... -
Page 111: Telephone Customer Service
When selecting a setting from the relay test, the relevant relay is energized, thus putting the connected component into operation. The correct functioning of the relays and wiring can thus be tested. 111/138 Siemens User Manual CE1U2353en Building Technologies Input / output test... -
Page 112: State
Protection mode, cooling Protection mode, cooling Frost protection plant active Frost protection active Cooling limit OT active Cooling limit OT active Room temp lim Flow limit reached Cooling mode off Cooling mode off 112/138 Siemens User Manual CE1U2353en Building Technologies State 2014-07-30... - Page 113 Max charg temp reached Charging DHW Charging DHW Charging buffer storage tank Charging buffer storage tank Radiation insufficient Min charg temp not reached Radiation insufficient Temp diff insufficient Radiation insufficient Radiation insufficient 113/138 Siemens User Manual CE1U2353en Building Technologies State 2014-07-30...
-
Page 114: Diagnostics, Heat Generation
Operating line 8610…8699 RVS46.543 only 6.21 Diagnostics, consumers For diagnostic purposes, the various setpoints, actual values, relay switching states and meter readings can be displayed. Line no. Operating line 8700…9099 114/138 Siemens User Manual CE1U2353en Building Technologies Diagnostics, heat generation 2014-07-30... -
Page 115: List Of Displays
Temperature limiter heating circuit 2 Error, cooling circuit Sensor error common message Sensor error common message Pressure supervision common message Flow sensor, solar sensor error Return sensor, solar sensor error 115/138 Siemens User Manual CE1U2353en Building Technologies List of displays 2014-07-30... -
Page 116: Maintenance Code
(dropped below lower pressure limit 3) 6.22.3 Special operation code Special Description operation code manual operation SLT test Chimney sweep function Simulation outside temperature Alternative energy operation Economy mode 116/138 Siemens User Manual CE1U2353en Building Technologies List of displays 2014-07-30... -
Page 117: Plant Diagrams
The basic diagrams are examples of plant that can be implemented with standard outputs requiring only a few settings. 7.1.1 Basic diagram RVS46.543 Standard diagram 7.1.2 Basic diagram RVS46.530 Standard diagram 117/138 Siemens User Manual CE1U2353en Building Technologies Basic diagrams 2014-07-30... -
Page 118: Extra Functions In General
DHW storage tank (DHW) RVS46.543 only DHW circulating pump DHW el imm heater 2. DHW sensor DHW tank with external heat exchanger, charging pump, intermediate circuit pump 118/138 Siemens User Manual CE1U2353en Building Technologies Extra functions in general 2014-07-30... -
Page 119: Heating/Cooling Circuit
Heating/cooling circuit Heating circuit pump HCP Diverting valve for cooling Heat converter System pump Q14 Extra functions H.. Pump Q15/18/19 119/138 Siemens User Manual CE1U2353en Building Technologies Extra functions in general 2014-07-30... -
Page 120: Extra Functions With Extension Module Avs75.390
6020 and 6021, and supplement the basic diagrams of the respective controllers. 2. Mixing valve heating circuit RG1/2 Cooling circuit 2-pipe 4-pipe Y1/Y2 Y23/Y24 Y1/Y2 Y23/24 Solar DHW heating 46.543 only 120/138 Siemens User Manual CE1U2353en Building Technologies Extra functions with extension module AVS75.390 2014-07-30... -
Page 121: Primary Controller
Primary controller Primary DHW controller 46.543 only Instantaneous DHW heater 46.543 only 121/138 Siemens User Manual CE1U2353en Building Technologies Extra functions with extension module AVS75.390 2014-07-30... -
Page 122: Legend Mains Voltage
DHW temperature outlet sensor Flow sensor primary controller Flow sensor cooling circuit DHW circulation sensor B39 Collector sensor Outside sensor Room unit 1 Room unit 2 Flow switch 122/138 Siemens User Manual CE1U2353en Building Technologies Extra functions with extension module AVS75.390 2014-07-30... -
Page 123: Technical Data
Max. switch-on current Max. total current (of all relays) AC 10 A Rated voltage range AC (24...230) V (for potentialfree outputs) External supply line protection Refer to section "Power supply" 123/138 Siemens User Manual CE1U2353en Building Technologies Basic units RVS… 2014-07-30... - Page 124 Storage to IEC721-3-1 class 1K3 temp. -20…65 °C Transport to IEC721-3-2 class 2K3 temp. -25…70°C Operation to IEC721-3-3 class 3K5 temp. 0...50 °C (noncondensing) Without packaging RVS46.543: 587 g Weight RVS46.530: 431 g 124/138 Siemens User Manual CE1U2353en Building Technologies Basic units RVS… 2014-07-30...
-
Page 125: Extension Module Avs75.390
2-wire connection, not interchangeable Interfaces Max. cable length Basic unit – peripheral device 200 m Max. total length 400 m (max. cable capacitance) 60 nF) Min. cross-sectional area 0.5 mm 125/138 Siemens User Manual CE1U2353en Building Technologies Extension module AVS75.390 2014-07-30... -
Page 126: Operator Unit And Room Units Avs37
Protection degree of housing IP20 for QAA7../ QAA55.. IP40 for AVS37.. (when mounted) according to EN 60529 Degree of pollution 2 according to EN 60730-1 126/138 Siemens User Manual CE1U2353en Building Technologies Operator / room units AVS37.., QAA7x, QAA55 2014-07-30... - Page 127 –20...70 °C Operation to IEC721-3-3 class 3K5 temperature 0...50 °C (noncondensing) Weight AVS37.294: 160 g Without packaging QAA75.61x: 170 g QAA78.610: 312 g QAA55.110: 115 g 127/138 Siemens User Manual CE1U2353en Building Technologies Operator / room units AVS37.., QAA7x, QAA55 2014-07-30...
-
Page 128: Power Supply Avs16.290
Storage to IEC721-3-1 class 1K3 temp. -20…65 °C Transport to IEC721-3-2 class 2K3 temp. -25…70°C Operation to IEC721-3-3 class 3K5 temp. 0...50 °C (noncondensing) Without packaging 310 g Weight 128/138 Siemens User Manual CE1U2353en Building Technologies Power supply AVS16.290 2014-07-30... -
Page 129: Radio Module Avs71.390
Storage to EN 60721-3-1 class 1K3, temp. -20…65 °C Transport to EN 60721-3-2 class 2K3, temp. -25…70°C Operation to EN 60721-3-3 class 3K5, temp. 0...50°C (non-condensing) Weight Without packaging 54 g 129/138 Siemens User Manual CE1U2353en Building Technologies Radio module AVS71.390 2014-07-30... -
Page 130: Wireless Outside Sensor Avs13.399
QAC34/101 Outside temperature acquisition Measuring range -50…70 °C Cable length max. 5 m Without packaging Radio transmitter 160 g Weight Outside sensor QAC34 73 g Cable 70 g 130/138 Siemens User Manual CE1U2353en Building Technologies Wireless outside sensor AVS13.399 2014-07-30... -
Page 131: Radio Repeater Avs14.390
-20…65 °C Transport to IEC721-3-2 class 2K3 temp. -25…70°C Operation to IEC721-3-3 class 3K5 temp. 0...50 °C (noncondensing) Weight Without packaging Radio repeater 112 g Power supply 195 g 131/138 Siemens User Manual CE1U2353en Building Technologies Radio repeater AVS14.390 2014-07-30... -
Page 132: Sensor Characteristics
21.0 1,170 -8.0 4,152 22.0 1,125 -7.0 3,958 23.0 1,081 -6.0 3,774 24.0 1,040 -5.0 3,600 25.0 1,000 -4.0 3,435 26.0 -3.0 3,279 27.0 -2.0 3,131 28.0 -1.0 2,990 29.0 132/138 Siemens User Manual CE1U2353en Building Technologies Sensor characteristics 2014-07-30... -
Page 133: Ntc 10 K
1591.9 1000.0 1309.0 1610.5 1019.5 1328.0 1629.1 1039.0 1347.1 1647.7 1058.5 1366.1 1666.3 1077.9 1385.1 1684.8 1097.3 1404.0 1703.3 1116.7 1422.9 1721.7 1136.1 1441.8 1740.2 1155.4 1460.7 1758.6 1174.7 1479.5 133/138 Siemens User Manual CE1U2353en Building Technologies Sensor characteristics 2014-07-30... - Page 134 Holiday program ............66 Default settings ............66 Holidays Default values ............66 end ..............66 Device address ............106 start ..............66 Device data .............106 Device version ............64 Input / output test ............ 111 134/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
- Page 135 Time of day ............... 62 Pure weather compensation ........70 Time programs ............65 Transfer boost ............89 Quick setback ............72 Type of charging ............89 Types of compensation ..........70 135/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
- Page 136 Weekday ..............62 Weather compensation ..........80 Wintertime ..............62 Weather compensation only ........80 With buffer storage tank ........76, 91 Weather compensation with room influence ..70, 80 With prim contr/system pump ........91 136/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30...
-
Page 137: Revision History
Hide: Ctrl Shift (Num) - Or select the same functionality with the following Winword menu: Menu: [Tools] - [Options] Command: [Highlight] The revision history is not visible in the print file (PDF). 137/138 Siemens User Manual CE1U2353en Building Technologies 2014-07-30... - Page 138 Siemens Switzerland Ltd © 2005-2014 Siemens Building Technologies Ltd. Building Technologies Group Subject to change Gubelstrasse 22 CH -6301 Zug Tel. +41 41-724 24 24 Fax +41 41-724 35 22 www.sbt.siemens.com 138/138 Siemens User Manual CE1U2353de Building Technologies 2014-07-30...