Advertisement
9. AFTER USE
9.1
Drain Tank
9.1.1
Disconnect the power supply and relieve the system
pressure by squeezing the spray gun trigger.
9.1.2
Use a suitable container to drain excess agent into, place it
beneath the drain hole.
9.1.3
Remove the drain cap to drain into container. Ensure all
personal protective equipment is used.
9.1.4
When the tank is fully drained, replace drain cap and tighten.
9.2
Unused chemicals
9.2.1
If unused agents are to be kept for future use store in the
original container or a similarly suitable one. Also ensure
such container is suitably labelled.
9.2.2
When remaining agents need to be disposed of, refer to the
manufactures label and local authority guidelines.
9.3
Flush Sprayer
9.3.1
Refer to agents manufacturer for flushing procedure and
recommendation on a cleaning solution.
9.4
Decontaminate
9.4.1
After handling chemicals and other agents, remove all
clothing and wash separate to other clothing.
9.4.2
Wash all exposed skin thoroughly with soap and water.
10. STORAGE
10.1
preparing for Storage
10.1.1 Add an antifreeze (not automotive) into the tank.
10.1.2 Turn on the pump and squeeze the gun trigger until the
antifreeze sprays briefly. Store the gun in the lance clips and
disconnect the power.
10.2
Removing form Storage
10.2.1 Drain the antifreeze into a suitable container.
10.2.2 Fill the sprayer tank with fresh clean water, connect the
power, use the spray gun and flush the system. be sure to
have a container to collect the flushed antifreeze.
10.2.3 Dispose of antifreeze along with local authority guidelines.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMpORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
iNFORMATiON: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
11. TROUBLESHOOTiNG
SYMPTOMS
Pump will not
start.
low pressure.
Low flow.
Poor spray
distribution.
Pump
operates while
not spraying.
12. SpRAY cALiBRATiON
Follow the below tables to determine the correct speed that the ATV
should travel.
12.1
12.1.1 Use the table that corresponds with the agents
12.1.2 Find the application rate that is closest to the agents
Litres per Hectare
Application Rate
Speed (km/h)
Litres per 100Sq.m.
Application Rate
Speed (km/h)
Litres per 10Sq.m.
Application Rate
Speed (km/h)
12.2
12.2.1 Use this table to set the speed of the ATV.
Speed (km/h)
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk business Park,
bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
REASON
1. Poor electrical
connection.
2. Short in wires
3. low
voltage.
1. Worn spray gun
nozzle.
2. Worn boom
nozzle.
1. clogged intake
tube.
2. clogged suction
strainer.
3. low voltage.
1. clogged intake
tube.
2. clogged suction
strainer.
3. Worn spray gun
nozzle
1. leak in the
system
Table 1
manufacturer's suggested application rate (litres per hectare,
litres per 100 sq.m or litres per 10 sq.m).
manufacturer's recommendations.
800
400
267
1
2
8.0
4.0
1
2
0.80
0.40
0.26
1
2
Table 2
Time Required in Seconds to Travel a Distance of:
10m
1
36
2
18
3
12
4
9
5
7
6
6
7
5
01284 757500
01284 703534
REMEDY
1. Ensure good connections.
2. check conditions of wires.
3. check the battery voltage.
1. Replace spray gun nozzle.
2. Replace boom nozzle.
1. Remove obstruction to
intake tube.
2. clean suction strainer.
3. check the battery voltage.
1. Remove obstruction to
intake tube.
2. clean suction strainer.
3. Replace spray gun nozzle.
1. Find leak and tighten hose
clamps or fittings.
Replace spray gun.
200
160
133
144
3
4
5
6
2.6
2.0
1.6
1.3
1.1
3
4
5
6
0.20
0.16
0.13
0.11
3
4
5
6
50m
100m
180
360
90
180
60
120
45
90
35
70
30
60
25
50
www.sealey.co.uk
Web
sales@sealey.co.uk
email
SS60, SS98
Issue: 1 - 23/11/11
7
7
7
Advertisement
