Sealey PWH616 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Charger
instructions Indoor use only
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
WARNING! This helmet is not suitable for use with laser welding or CUTTING or for overhead welding applications.
Ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. The helmet will not
9
offer protection against misuse of workshop tools, equipment, or accessories.
Maintain the helmet in good condition and protect cartridge from liquid and dirt contact. Regularly replace the protective lens and
9
replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Ensure the front cover window is securely in place before use.
9
Fit the helmet and adjust the head band so the helmet will sit as low and near to your face as possible.
9
Use helmet only in temperatures ranging from -5°C to 55°C.
9
Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery.
9
Maintain correct balance and footing.
9
Ensure the floor is clear from obstructions, not slippery and wear non-slip protective shoes.
9
Keep children and unauthorised persons away from the working area.
9
WARNING! The helmet will only protect the eyes and face from radiation and sparks. It will not protect against explosive devices or
‰
corrosive liquids.
DO NOT use helmet for any purpose for which it is not designed.
8
DO NOT use helmet unless you have been instructed in its use by a qualified person.
8
DO NOT open or tamper with the shade cartridge.
8
DO NOT get the helmet wet or use in damp or wet locations.
8
DO NOT leave work place with helmet in lowered position, as bright light source may darken cartridge unexpectedly.
8
© Jack Sealey Limited
WELDING HELMET WITH POWERED AIR
PURIFYING RESPIRATOR (PAPR)
PWH616
MODEL NO:
Original Language Version
Recommended fuse rating:
3 A
PWH616 Issue 1 04/12/20