Sealey Power Tools SA36.V2 Instructions

Item Part No. Description
1 SA36.V2-01 Clamp
2 SA36.V2-02 Set Screw
3 SA36.V2-03 Punch Die
4 SA36.V2-04 Guide Bushing
5 SA36.V2-05 Cup Spring
6 SA36.V2-06 Punch
7 SA36.V2-07 Screw
8 SA36.V2-08 Cover Plate
9 SA36.V2-09 Anvil
10 SA36.V2-10 Oil Seal
11 SA36.V2-11 Support Ring
12 SA36.V2-12 O-ring
13 SA36.V2-13 Oil Plug
14 SA36.V2-14 O-ring
15 SA36.V2-15 Hydraulic Cylinder
16 SA36.V2-16 Air Cylinder
17 SA36.V2-17 Plastic Wrap
18 SA36.V2-18 Valve Body
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
Issue: 1
Date Issue: 290802
Item Part No. Description
19 SA36.V2-19 Air Inlet
20 SA36.V2-20 Throttle Lever
21 SA36.V2-21 Spring Pin
22 SA36.V2-22 O-ring
23 SA36.V2-23 Push Rod
24 SA36.V2-24 Spring
25 SA36.V2-25 Valve
26 SA36.V2-26 Spring
27 SA36.V2-27 O-ring
28 SA36.V2-28 Screw
29 SA36.V2-29 O-ring
30 SA36.V2-30 Support Ring
31 SA36.V2-31 Hydraulic Piston
32 SA36.V2-32 O-ring
33 SA36.V2-33 Support Ring
34 SA36.V2-34 Spring
35 SA36.V2-35 Piston
36 SA36.V2-36 O-ring
E-mail: sales@sealey.co.uk
01284 703534
Web: www.sealey.co.uk
INSTRUCTIONS FOR
AIR PUNCH/FLANGE TOOL
SA36.V2
Model:
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
Follow all workshop Health & Safety rules, regulations and conditions when using this tool.
!
WARNING! Disconnect from air supply before servicing.
F
Maintain tool in good condition and replace any damaged or worn parts. Use genuine parts only.
!
Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
F
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use
!
and ensure that all connections are secure.
WARNING! Always wear approved eye and face protection when operating the tool.
F
Wear ear defenders and gloves if necessary.
!
Keep hands and body clear of the workpiece when operating the tool.
!
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
!
Secure unstable workpiece with a clamp, vice or other adequate holding device.
!
Keep children and non-essential persons away from the work area.
!
DO NOT get the tool wet or use in damp or wet locations.
%
DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
%
DO NOT use the tool for a task it is not designed to perform.
%
WARNING! DO NOT use the tool if damaged or faulty. Contact your local service agent.
F
p
DO NOT use the tool unless you have been instructed in its use by a qualified person.
%
DO NOT carry the tool by the air hose, or yank the hose from the air supply.
%
% DO NOT direct air from the air hose at yourself or others.
% DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.
! When not in use, disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATION
2.1. Introduction
Suitable for heavy bodyshop use. Aluminium alloy body with steel punch and die. Puts a 10mm flange
onto car-panel-thickness sheet for lap jointing and puts 6mm holes in panels for mig spot-welding.
2.2. Specification
Operating Pressure . . . .90psi (6.2 bar)
Air Inlet . . . . . . . . . . . . . . . . . 1/4”BSP
Weight . . . . . . . . . . . . . . . . . . . . 1.3kg
Vibration . . . . . . . . . . . . . . . . .<2.5m/s
2
Noise . . . . . . . . . . . . . . . . . .81.7dB(A)
Spare Punch . . . . . . . . . . . . .SA36/36
Spare Die . . . . . . . . . . . . . . . SA36/40
SA36.V2 - 1 -290802