Table of Contents
Advertisement
Technical Information
Aspect Ratio: 4:3
Size 1
Size 2
Aspect Ratio: FULL/JUST(H-FILL/ZOOM)
Size 1
Size 2
See pages 24-25 for more information
Input signal that can be displayed
* Mark: Applicable input signal for Component (Y, P
horizontal frequency (kHz)
525 (480) / 60i
15.73
525 (480) /60p
31.47
750 (720) /60p
45.00
1,125 (1,080) /60i
33.75
1,125 (1,080) /60p
67.43
1,125 (1,080) /60p
67.50
1,125 (1,080) /24p
26.97
1,125 (1,080) /24p
27.00
640 × 400 @70
31.47
640 × 480 @60
31.47
Macintosh13" (640 × 480)
35.00
640 × 480 @75
37.50
852 × 480 @60
31.47
800 × 600 @60
37.88
800 × 600 @75
46.88
800 × 600 @85
53.67
Macintosh16" (832 × 624)
49.73
1,024 × 768 @60
48.36
1,024 × 768 @70
56.48
1,024 × 768 @75
60.02
1,024 × 768 @85
68.68
Macintosh 21" (1,152 × 870)
68.68
1,280 × 768 @60
47.70
1,280 × 1,024 @60
63.98
1,366 × 768 @60
48.36
Note
Signals other than above may not be displayed properly.
The above signals are reformatted for optimal viewing on your display.
PC Input Terminals Connection
Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency
of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
Some PC models cannot be connected to the set.
There is no need to use an adapter for computers with IBM PC/AT compatible D-sub 15P terminal.
The maximum resolution: 1,280 × 1,024
If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.
Signal Names for D-sub 15P Connector
Pin No.
Signal Name
11
12
13
14
15
6
7
8
9
10
1
2
3
4
5
NC (not connected)
46
GND (Ground)
Pin Layout for PC Input Terminal
(Continued)
H size
The width will be decreased on both sides to
reduce noise.
The width will be increased on both sides to
reduce noise.
, P
), HDMI and PC
B
R
vertical frequency (Hz)
COMPONENT
HDMI
*
59.94
*
59.94
*
59.94
*
59.94
59.94
60.00
23.98
24.00
70.08
59.94
66.67
75.00
59.94
60.32
75.00
85.08
74.55
60.00
70.07
75.03
85.00
75.06
60.00
60.02
60.00
Pin No.
Signal Name
Pin No.
Signal Name
R
GND (Ground)
NC (not connected)
G
GND (Ground)
B
GND (Ground)
NC (not connected)
GND (Ground)
Care and Cleaning
First, unplug the Power cord plug from the wall outlet.
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-
free cloth.
If the surface is particularly dirty, soak a soft, lint-free cloth in diluted mild liquid dish soap (1 part mild liquid dish soap diluted
by 100 times the amount of water) and then wring the cloth to remove excess liquid. Use this cloth to wipe the surface of the
display panel, then wipe it evenly with a dry cloth of the same type until the surface is dry.
Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid contact with volatile
substances such as insect sprays, solvents, and thinner; otherwise, the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in a weak mild liquid dish soap and then wring the cloth dry.
Use this cloth to wipe the cabinet and then wipe it dry with a dry cloth.
Do not allow any mild liquid dish soap to come into direct contact with the surface of the LCD TV.
If water droplets get inside the unit, operating problems may result.
Avoid contact with volatile substances such as insect sprays, solvents, and thinner; otherwise, the quality of the cabinet surface
may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made
from rubber or PVC.
PC
*
*
*
Cleaning
*
Wipe the surfaces with a soft, dry cloth. If the unit is particularly dirty, clean it using a cloth soaked with water to
*
which a small amount of mild liquid dish soap has been added and then wipe with a dry cloth.
*
Do not use products such as solvents, thinner, or household wax for cleaning, as they can damage the surface
*
coating. (If using a chemically-treated cloth, follow the instructions supplied with the cloth.)
*
Do not attach sticky tape or labels, as they can make the surface of the pedestal dirty. Do not allow long-term
*
contact with rubber, vinyl products, or the like. (Doing so will cause deterioration.)
*
*
*
*
*
Wipe the plug with a dry cloth at regular intervals. (Moisture and dust can lead to fire or electrical shock.)
*
*
*
*
*
*
*
*
*
*
*
NC
HD/SYNC
VD
NC
Display panel
Cabinet
Pedestal
Power cord plug
47
Advertisement
Table of Contents
