Advertisement
Available languages
Available languages
25
Specifications
General
Power
requirements:
AC
110-240 V
,
50/60 Hz
Power
consumption:
12W
Dimensions
(Approx.):
430x39x242mm(WxHxD)withoutfoot
Weight (Approx.):
2.2
kg
Operating
temperature:
5°Cto35°C(41°Fto95°F)
Operating humidity:
5 % to 90 %
Outputs
VIDEO OUT:
1
Vp-p
75
Ω,
sync
negative,
RCA
jack
x
1/
SCART
(TO TV)
AUDIO OUT:
2.0Vrms(1KHz,0dB),600Ω, RCAjack(L,R)x1/
SCART
(TO TV)
DIGITAL OUT
(COAXIAL):
0.5V(p-p),75Ω,RCAjackx1
System
Laser:
Semiconductor
laser,
wavelength
650
nm
Signal
system:
PA
L/NTSC
Frequency
response:
DVD(PCM96kHz):8Hzto44kHz
DVD(PCM48kHz):8Hzto22kHz
CD:8Hzto20kHz
Signal-to-noise
ratio:
More than 100 dB
(ANALOG
OUT
connectors
only)
Harmonic distortion: Less than 0.008%
Dynamic
range:
More than 90 dB
(DVD/CD)
Accessories
Video cable
(1),
Audio cable
(1),
Remote control
(1),
Batteries
(2)
Note:
Design
and
specifications
are
subject
to
change prior
notice.
Symptom
No power.
The power is
on,
but
the DVD
player
does
not
work.
No
picture.
No sound.
The DVD
player
does
not start
playback.
The
remote
control
does
not
work
properly.
Possible Cause
?
The power cord is disconnected.
?
No disc is inserted.
?
The TV is
not set to
receive DVD
signal
output.
?
The video cable is
not
connected
securely.
?
The
equipment
connected with the
audio cable is
not set to
receive DVD
signal
output.
?
The power of the
equipment
connected
with the audio cable is turned off.
?
The AUDIO
options
are
set to
the
wrong
position.
?A
n
unplayable
disc is inserted.
?
The
rating
level is
set.
?
The
remote
control is
not
pointed
at
the
remote
sensor on
the DVD
player.
?
The
remote
control is
too
far from the
DVD
player.
Correction
?
Plug
the power cord into the wall outlet
securely.
?
Insert
a
disc.
(Check
that the DVD
or
audio CD indicator in the
display
window is
lit.)
?
Select the
appropriate
video
input
mode
on
the TV.
?
Connect the video cable
securely.
?
Select the
correct
input
mode of the
audio receiver
so
you
can
listen
to
the
sound from the DVD
player.
?T
urn on
the
equipment
connected with
the audio cable.
?
Set the
Digital
Audio
Output
to
the
correct
position,
then
turn
on
the DVD
player again by pressing
POWER.
?
Insert
a
playable
disc.
(Check
the disc
type,
color
system,
and
regional code.)
?
Cancel the
rating
function
or
change
the
rating
level.
?
Point the
remote
control
at
the
remote
sensor
of the DVD
player.
?
Operate
the
remote
control closer
to
the DVD
player.
Troubleshooting
P/NO: 3834RD0018L
Advertisement
